1

OWNER’S MANUAL500 Plus Series, 1000 Series, Model 706 Toilets

VACUFLUSH®

SANITATION SYSTEM

IMPORTANT NOTICE

VacuFlush® sanitation systems

must be installed according to

Dometic’s recommended procedures.

Do not attempt installation without

first contacting a SeaLand

Product certified dealer or

Dometic Corporation.

Dometic Corporation • Sanitation Systems13128 State Rt. 226, P.O. Box 38Big Prairie, OH 44611-0038 USA

SeaLand Product Hotline 1-800-321-9886(8:00 a.m. - 5:00 p.m. ET)

This manual must be read and understoodbefore adjustment, maintenance, or serviceis performed. Modification of this productcan result in property damage.

WARNING!

2

Dometic brings the technology, comfort and efficiency of VacuFlush Sanitation Systems in an easy-to-use and easy-to-maintain package.

• Freshwater Flush• Eliminates the unpleasant sulfide odors which plague saltwater systems.• Eliminates the need to draw flush water through the through-hull, seacock and vented loop.• Significantly extends life of system components by eliminating saltwater and impurities from

accumulating in the system over time.• Efficient Design

• Consumes a little over a pint of water per flush and allows boat owners to use a small waste tank.The VacuFlush system fills a ten-gallon (28.4 liter) tank in the same time that an electric toilet fills a40-gallon (113.6 liter) tank.

• Uses only 4-6 amps per flush on 12 VDC.• Delightful Operation

• Simple one-lever flush control. No complex instructions needed.• Comfortable adult-sized seat.• Large water surface maintains clean bowl.• Vitreous china bowl.

• Reliability is Built-In• USCG Certified Type III Marine Sanitation Device.• No impellers or macerators – vacuum pump motor can run dry without burning up. No dynamic seals.• Vacuum tank and vacuum generator design eliminates clogging problems associated with other

systems.• Dispose of Sewage Conveniently and Safely

• Toilet can be used without discharging sewage into sensitive waters.• Holding tank discharge is at a dockside pump or at sea with optional overboard discharge.• No portable toilet tanks to haul or dump.

• Backed by the Best in Service and Quality• The VacuFlush system is from the leader in marine sanitation.• Worldwide parts availability and technical backup.

PRODUCT FEATURES

TABLE OF CONTENTSPage Page

Product Features . . . . . . . . . . . . . . . . . . . . . . 2Marine Sanitation Regulations . . . . . . . . . . . . 3Important Information Before Operation . . . . 3Key System Components . . . . . . . . . . . . . 4 - 5System Start Up . . . . . . . . . . . . . . . . . . . . . . 5Proper Cleaning . . . . . . . . . . . . . . . . . . . . . . 5Winterizing . . . . . . . . . . . . . . . . . . . . . . . . . . 5Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 6Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . 6VacuFlush Maintenance Kit . . . . . . . . . . . . . . 7Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . 7Toilet Model Identification . . . . . . . . . . . . . . . 7

Pedestal and Pedal Cover Installation . . . . . . 7Deodorants and Special Tissue . . . . . . . . . . . 8Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 9Vacuum Tester . . . . . . . . . . . . . . . . . . . . . . . 9Service Tip . . . . . . . . . . . . . . . . . . . . . . . . . . 9Troubleshooting Guide . . . . . . . . . . . . . 10 - 12Parts Lists . . . . . . . . . . . . . . . . . . . . . . . 13 - 20Dimensional Specifications . . . . . . . . . . . . . 21Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . 22Parts Distributors . . . . . . . . . . . . . . . . . . . . . 23Manufacturer’s One-Year Limited Warranty 24

WARNING – HIGH VOLTAGE SYSTEM.Turn off electrical power before servicing.

WARNING – PUMP STARTS AUTOMATICALLY.Turn off electrical power before servicing.

Dometic reserves the right to change specifications without notice.

3

MARINE SANITATION REGULATIONS

IMPORTANT INFORMATION BEFORE OPERATION1. Fill freshwater tank and add deodorant to holding tank through toilet bowl.

(See System Start Up Section)2. Make sure all guests understand the operation of the VacuFlush system

and the instruction label is in plain sight and easy for guests to read.If this label is not included in this manual, please contact the SeaLandProduct Customer Service Department immediately.

3. Remember the vacuum pump starts automatically. Shut off the system before servicing and do not leave theboat with toilet system breaker on.

4. Never use drain openers, alcohol, solvents, etc. in the system.5. If the system does not function properly, refer to the Troubleshooting Section of this manual and repair as

necessary. If problem persists, contact your local SeaLand dealer or see the Parts Distributor section of thismanual.

1. To add water to the toilet beforeusing, raise flush lever until desiredwater level is reached. Generally, morewater is required only when flushingsolids.

2. To flush toilet, press flush leversharply down to the floor until contentsclear bowl. A sharp popping noise isnormal when the vacuum seal is bro-ken and flushing action begins. Be sureto hold lever down for three (3) sec-onds. If flush lever is accidentally re-leased before waste clears bowl, do notattempt to flush toilet again untilvacuum pump stops running. A smallamount of water should remain in thebowl after flushing.

3. Do not dispose of sanitary napkinsor other non-dissolving items in toilet,such as facial tissue or paper towels.These items can cause plugging of thesystem. Refer to the Deodorants andSpecial Tissue section in this manualfor more information.

All boats with fixed toilets in U.S. waters and in the waters of some other countries are required to be equippedwith an operable marine sanitation device (MSD). The VacuFlush system is a holding tank or Type III system asdefined by the U.S. Coast Guard.

Type III systems are designed to permit operation of the toilet without the direct discharge of untreated wasteafter every flush. This means onboard toilet facilities can be used when the boat is near swimmers, beaches orshellfish beds.

Type III systems can be discharged at marina dockside pump-out stations or, if in coastal waters, a minimum ofthree miles offshore. Overboard discharge capability must remain secured while within the three-milelimit. The overboard discharge pump is activated by a keyed switch located in the toilet compartment. This keyshould be removed at all times except when discharge pump is operating.

Federal legislation has provided grants to private marinas to install dockside pumps especially in coastal water.It is estimated that over 3,500 pump-out stations, in total, will be added due to this legislation.

Sewage from any source should not be discharged directly into our waters. If you are interested in learning moreabout this issue, please contact SeaLand at the phone number or address listed on the back page of this manual.Request Clean Water Notebook, Volumes 1 and 2.

NORMAL OPERATION

4

KEY SYSTEM COMPONENTS

Vacuum Toilet: The VacuFlush toilet operates in a way different from other marine toilets. VacuFlush systems usea small amount of water (a little more than a pint or .5 liter) per flush in addition to a simple vacuum. The toilet isconnected to a pressurized freshwater system. Fresh water is the key to an odor-free bathroom compartment.VacuFlush toilets are equipped with an integral vacuum breaker which prevents the possible contamination of thepotable water supply.

Vacuum Tank: The vacuum tank stores vacuum energy. System vacuum level is monitored by a vacuum switchlocated on the vacuum tank. When this switch senses a drop in vacuum in the system, it automatically signals thepump to energize and bring the vacuum to operating level. This process is normally completed in less than oneminute. In a properly operating system, the stored vacuum will slowly dissipate between flushes, permitting thevacuum pump to quickly renew the vacuum.

Vacuum Pump: The vacuum pump is an electric, straight-through bellows type. It is manufactured of long-lastingpolypropylene and draws only 4 to 6 amps of current at 12 VDC. This unique pump design is both an efficient air andliquid pump that handles solids without a problem. It has two duckbill valves on each side of the pump chamber toprevent backflow of waste and vacuum.

Vacuum Generator: The vacuum generator combines the vacuum tank and vacuum pump in one unit.It greatly reduces installation time and eliminates the hose run between the tank and pump. Its compact size makesit especially well-suited to smaller crafts.

Holding Tanks: Holding tanks from Dometic are made of super-strong, 3/8" (9.5mm) thick polyethylene — 50%thicker than most other holding tanks. Each unit has a solid, one-piece construction with no seams for unmatcheddurability. Tanks come in several capacities and shapes. Contact Dometic for details. A deodorant additive isrequired to keep the holding tank odor-free. See Deodorants and Special Tissue section for further information.

TankWatch® Level Indicator: The TankWatch unit utilizes micro-float switches which activate an indicator panel.The inspection cap in the holding tank contains the micro-float switch units. The adjustable probe assemblies areflexible polybutylene tubing and are designed to flex when tank contents move.

In-Line Vent Filter: Our SaniGardTM vent filter has special odor-removing filter materials to help keep your boatsmelling clean and pleasant. Heavier-than-air malodors accumulate in the holding tank. The SaniGard vent filter hasa special type of activated filter media to remove these odors before they offend. Each cartridge is good for an entireseason, and is easily replaced for a fresh start. Replacement cartridges are available from your local marine dealer.

Dockside Discharge Deck Fitting: The holding tank is connected to a deck discharge fitting. This fitting, in turn, canbe connected to a dockside pump which may have a rubber, cone-shaped nozzle or a cam lock fitting. Refer toAccessories section for further information on the NozAll™ fitting which makes using a dockside pump easy andconvenient.

Discharge Pump: Our T-series SaniPumpTM discharge pump can run dry without harm and draws just 6 amps at 12VDC. The discharge pump has a flow rate of just over 5.25 gallons per minute (11.4 liters per minute). Emptying anonboard tank usually takes four to six minutes. The T-pump is connected to a through-hull fitting. Check the sectionon Marine Sanitation Regulations for information on areas where discharge is allowed.

5

SYSTEM START UP1. Turn on inlet water supply.2. Turn on electrical power to system.3. Flush water into system by depressing flush lever until water starts flowing to the vacuum pump, approxi-

mately 15 seconds. The vacuum pump will run for approximately 60 to 90 seconds until system reachesoperating vacuum level and then will shut off.

WINTERIZING

At the end of each season, the SeaLand toilet should be winterized forstorage, by either draining or using potable water-safe antifreeze in thesystem.To drain:1. Thoroughly flush system with fresh water.2. Empty holding tank.3. Shut off water supply to toilet(s), and remove inlet waterline (Fig. C).

Do not remove brass cap on bottom of valve.4. Press flush lever until all water is drained from toilet(s).To use antifreeze:1. Drain potable water tank.2. Add freshwater antifreeze to potable water tank.3. Flush potable water antifreeze and water mixture through toilet(s) and into the waste holding tank. Each

installation is different, so amounts may vary. User discretion is required to assure adequate protection.4. Empty holding tank.NOTE: Use nontoxic antifreeze designated for potable water systems. (See vehicle owner’s manual.)CAUTION: Never use automotive-type antifreeze in freshwater systems.

The SeaLand toilet should be cleaned regularly for maximum sanitation andoperational efficiency. You can clean it just as you would a household toilet.Do not use caustic chemicals, such as drain-opening types, as theywill damage the seals.BOWL CLEANING: For stubborn stains, use SeaLand® Bowl and SealCleaner (Fig. A). It’s manufactured especially for use with SeaLand toilets.In certain locations where water is hard, a build-up of lime may dull the toiletbowl finish. Restore the shine with this SeaLand cleaner. If you cannot findit in your area, contact SeaLand for your nearest dealer. If the cleaner is notavailable, you can also use Bar Keepers Friend® cleanser. It is not neces-sary to vigorously scrub with either product. Please follow label instruc-tions.SEAL CLEANING: After an extended time, mineral deposits from hardwater can build up under the edge of the rubber bowl seal, resulting in aslow leakdown of water from the bowl. To prevent this mineral build-up,periodically clean under the bowl seal with SeaLand Bowl and Seal Cleaner(Fig. B).1. Shut off water supply.2. Apply cleaner onto the seal cleaning tool (supplied with new toilet), open

the flush ball by pressing on flush lever, and scrub under the seal. Makesure to push bristles between bottom of seal and top of flush ballsurface to scrub all parts of seal that come into contact with flush ball.

3. Close ball and wait 2-3 minutes.4. Open flush ball. Use brush and water to rinse away cleanser and loosened deposits.

PROPER CLEANING

Fig. A

Fig. B

Fig. C

6

MAINTENANCEMaintenance intervals and normal parts replacement vary widely depending on numerous factors such as: typeof vessel, frequency of system use, quality of flushing water, etc. The chart below is intended strictly as ageneral guideline. Owner discretion and consideration of actual usage must be the first basis for determiningproper maintenance levels.

SPARE PARTSTo calculate total spare parts required, determine number and type of toilets and pumps.

*See Base Assembly - Page 10.

Maintenance ProcedureFollow cleaning procedures (page 5).Tighten all clamps, including base clamp ring.*Check all wire connections.Check & tighten water valve mounting screws.Clean filter screen in water valve.Check pump and in-line valves.Check toilet seals.Check vacuum breaker.Check water valve.

Part Number—————

385310076 (2)385316140385316906385314349

Approximate Maintenance LevelMonthlyAnnuallyAnnuallyAnnuallyAnnually

2-3 years or as needed3-5 years or as needed3-5 years or as needed3-5 years or as needed

Type of SystemToilet Series& Quantity

Pump Series& Quantity

ToiletSealKit

ToiletWaterValve

Kit

S PumpDuckbillValve Kit

M PumpDuckbillValve Kit

ToiletVacuumBreaker

VacuumTank

VacuumSwitch

ToiletRing/

ClampKit

ToiletBall/ShaftCartridge

Kit

On Board Spare Parts Calculation Chart: (Per System)

500+12

123456

1000

12

123456

S1212

M *

111111111111

1 each1 each1 each1 each1 each1 each1 each2 each2 each2 each1 each1 each1 each2 each2 each2 each

1 each1 each1 each1 each1 each1 each1 each2 each2 each2 each1 each1 each1 each2 each2 each2 each

2 each2 each2 each2 each

4 each4 each4 each4 each4 each4 each4 each4 each4 each4 each4 each4 each

1 each

1 each

1 each1 each2 each2 each2 each

1 each1 each2 each2 each2 each

1 each1 each1 each2 each

1 each1 each1 each2 each

1 each1 each1 each2 each

1 each1 each1 each2 each

1 each

1 each

1 each1 each1 each1 each2 each

1 each1 each1 each1 each2 each

Per Vessel: Vacuum Tester – 530002 (1 each) & Owner’s Manual – (1 each)

1 each1 each1 each2 each

1 each1 each1 each2 each

VacuumGenerator

SwitchKit

1 each1 each1 each2 each

1 each1 each1 each2 each

Low-ProfileVacuum

GeneratorSwitch Kit

* M series pump parts information is contained in a separate M-Pump Owner’s Manual.

7

VACUFLUSH MAINTENANCE KITThe VacuFlush Maintenance Kit contains replace-ment parts used in routine maintenance of Vacu-Flush toilets. A “must” for those who cruise to re-mote locations. The kit includes vacuum tester,water valve, seal kit, duckbill valves (4) and anowner’s manual in a convenient storage container.

ORDERING PARTSDometic is ready to assist you in the event service is required. Before calling, please have the following informa-tion available. Your cooperation in having this information ready is appreciated and allows us to better meet yourneeds. Please refer to the Parts Distributor list on Page 23.

1. Toilet Model Number (See following section.)2. Serial Number3. Part Number, Description and Quantity (See Parts information.)

TOILET MODEL IDENTIFICATION

The above label is located on the toilet base and will show the model number and serial number. If label is notavailable, please refer to the Dimensional Specifications section for toilet model identification.

PEDESTAL AND PEDAL COVER INSTALLATION

1. With the pedestal cover open, place the back halfagainst the side of the base opposite the flush lever.Rotate the pedestal cover counterclockwise around theback of the base, then move the front half into place.

2. Tall base unit only, secure with mounting screw.For short base units, simply snap cover closed.

3. Slide pedal cover onto foot pedal rod.4. Attach pedal cover side plate and secure with

two (2) mounting screws. For short base units,secure front screw, then press foot pedal downcompletely to secure second screw.

1

3 4

2

VacuFlushMaintenance Kit(item number 310228)

DOMETIC CORPORATIONP.O. BOX 38, 13128 STATE RT 226 (800) 321-9886BIG PRAIRIE, OH 44611 USA

MODEL NO. 000SERIAL NUMBER

000000

8

DEODORANTS AND SPECIAL TISSUEYour VacuFlush sanitation system requires the regular addition of a deodorant product to reduce malodors andto help break down holding tank contents. Several factors should be considered in selecting a deodorantproduct.

Liquid or Granulated: Liquid products obviously work more quickly by readily going into solution. Granulatedpowder formulations, on the other hand, have the advantage of requiring less storage space and are less likelyto leak if the package is inadvertently damaged.

Formaldehyde versus Non-Formaldehyde: Dometic manufactures both types of deodorants. Generallyspeaking, formaldehyde formulas control odor very effectively at all temperatures and with all degrees of waterhardness. SeaLand Environment-Friendly brand, which is formaldehyde free, is similarly effective.

Environmental Hazards: If you would like further information on the impact of holding tank deodorants, call orwrite Dometic at the number and address listed on the back page of this manual. Request a copy of CleanWater Notebook, Volume 5, which provides complete information in this regard.

How Much Deodorant and How to Add It: The deodorant is added directly into the toilet bowl, then flushedinto the holding tank. Follow bottle or package instructions. Conditions of extremely warm weather, longerwaste holding time and larger tank capacities may require more deodorant treatment. Also, to maintain opti-mum efficiency in odor control, the waste holding tank should be cleaned thoroughly at least once or more eachseason depending on use.

Why Not Use Household Toilet Paper in Your SeaLand Toilet. Household tissues often contain adhesiveswhich bond together the paper fibers from which the tissue is made. The adhesives prevent the tissue frombreaking apart, and their use in “ultra-low flow” systems can cause system clogging. SeaLand tissue is espe-cially designed for use in low water toilet systems. Its rapid dissolving properties minimize the amount ofresidual paper in the holding tank and allow deodorizers to work more efficiently.

SeaLand versus Other Brands: Dometic constantly strives to provide our system owners with effectiveproducts that have minimal environmental impact and good value. Many other deodorant products do notmeasure up to our standards of performance and value.

SeaLand® GranulatedDeodorant

Six 2-oz. pouches

Part No.379626002

SeaLand® LiquidDeodorant

Two 8-oz. bottles Part No.

379224008

SeaLand®

Cleaner16-oz. bottle

Part No.379314016

SeaLand® LiquidDeodorant -

Environment Friendly32-oz. bottle

Part No.379114032

SeaLand®

Rapid-DissolvingToilet Tissue

Four 400-sheet rolls Part No.

379441204

9

ACCESSORIESNozAllTM Pumpout Adapter: The NozAll pumpout adapterprovides an airtight seal between your boat’s deck wastefitting and the pumpout station nozzle. Just screw yourpersonal NozAll adapter into your deck fitting, and be as-sured of an airtight connection for pumping out holding tankcontents. Each item contains a glass-filled nylon NozAlladapter, gasket and vinyl cap. Item number 343502 (1-1/2"-11.5 tpi), 343503 (1-1/4"-11.5tpi), or 343504 (1-1/4"-16tpi).

VacuFlush Status Panel: An ideal add-on to anyVacuFlush system. The Status Panel is mounted in thebathroom compartment. A green light indicates sufficientvacuum is available for the next flush. A red light indicatesthe vacuum level is building and the pump is running. Eachpanel has an integral circuit breaker which allows thesystem to be shut down at night. Order part number 500012(12VDC) or 500024 (24/32VDC).

Optional Vacuum Generator Shut-down Relay: Thisrelay can be added to automatically shut down power tothe VacuFlush toilet system to prevent overfilling of theonboard holding tank. Order part number 310289 (12 VDC)or 310290 (24 VDC).

VACUUM TESTER

Dometic has developed a simple tool to assist inidentifying the location of vacuum leaks. Thevacuum tester consists of a vacuum gauge and acone-shaped plug. Inserting the plug in the inlet ofthe vacuum tank or generator isolates the toilet fromthe system. In this way a troublesome leak caneasily be located in either system.

Order only the Vacuum Tester (Part Number530002) or as part of the complete system mainte-nance kit (Part Number 310228).

SERVICE TIPChecking for water leaks behind or under toilets or other appliances can make it difficult to locate the source.Dripping water at room temperature makes it difficult to feel wetness. Taking four or five sheets of toilet tissueand wiping all seams and waterline connections offers a simple means of locating the general area of the leak-age. Start at the top of the unit since gravity will cause a leak to run downward. When the tissue comes incontact with the leaking water, it will immediately change texture.

Vacuum Tester

VacuFlushStatus Panel

VacuStat™ Indicator Panel: A desirable accessory forVacuFlush sanitation systems, this panel continuouslymonitors the status of vacuum for proper toilet operation.Brushed metallic finish complements bathroom decor. Or-der part number 700012 (12 VDC) or 700024 (24 VDC).

*Deck Fitting

*Nozzle

*Not included.

NozAll™ Adapter

VacuStatIndicator Panel

10

BASE ASSEMBLY

REAR VIEW, VACUUM TOILET

TROUBLESHOOTING GUIDE

1. Water will not stay in bowl.

2. Plastic flush ball will notclose completely.

3. Flush ball will not open.

4. Water does not shut off intoilet (toilet overflows).

5. Water does not enter toiletbowl properly.

a. Loose clamp ring.b. Improper seal around flush ball due

to dirt or debris on underside of ballseal.

c. Worn or damaged seal.d. Worn or damaged flush ball.

a. Too much friction between flush balland ball seal.

b. Water valve screws are too tight.c. Defective spring cartridge.

a. Broken shaft.b. Shaft not fully engaged in the

spring cartridge.

a. Not enough clearance between camstrap and top of water valve cap.

b. Dirt lodged in water valve seal.

a. Insufficient water flow rate at toilet.

b. Water valve clogged.

c. Plugged rim wash holes in toilet.

a. Tighten clamp ring adjusting nut.b. Inspect flush ball and underside of

seal for foreign objects. Clean underseal if needed (cleaning toolavailable – p/n 600344236).

c. Replace seal.d. Replace flush ball.

a. Lubricate between flush ball andball seal with furniture polish orcooking spray.

b. Loosen screws slightly.c. Check spring tension by pushing

flush lever down, then release itsuddenly. If lever does not snapback into original position, replacespring cartridge.

a. Replace shaft.b. Put pressure on shaft from under

the flush ball (pushing into springcartridge) until it engages. You mayhave to rotate flush ball slightly untilshaft lines up with square inspring cartridge.

a. Adjust cam strap to have .02"(.5mm) minimum clearance with topof valve cap.

b. Disassemble and clean watervalve.

a. Check water flow rate at toilet. Rateshould be 2 gpm (7.6 lpm) at toilet.

b. Remove and clean screen locatedat inlet of water valve.

c. Clean holes. If still a problem,replace the toilet bowl.

Problem Possible Cause Service Instructions

VACUUMBREAKER WHITE CAP

HOSECONNECTION

VACUUM BREAKER/BOWL CONNECTION

11

TROUBLESHOOTING GUIDE

6. Lifting foot pedal does notadd water to the bowl.

7. Water leaking from watervalve.

8. Water leaking from rear oftoilet bowl.

9. Water is leaking from thebase/toilet connection.

10.Vacuum pump running toooften between flushes.(See Vacuum TesterInformation on page 9.)

11.Vacuum pump will notshut off.

12.Vacuum pump will not run.

a. Too much clearance between thecam strap and water valve.

a. Water valve body cracked due tofreeze damage.

b. Water line connection is loose or notseated properly.

c. Defective water valve.d. Stripped threads.

a. Worn or defective vacuum breaker.

b. Loose vacuum breaker.

c. Cracked or defective toilet bowl.

a. Clamp ring may be loose.

b. Ball seals may be worn or defective.

a. Water leaks out of bowl betweenflush ball and ball seal.

b. Vacuum line leak.

a. A vacuum leak exists.b. Insufficient vacuum (pump creates

less than 10 inches Hg).

c. Faulty vacuum switch (pump createsmore than 10 inches Hg).

d. Improper wiring.

e. Bellows not pumping.

a. No electrical power.

b. Loose or broken electrical wiring.

c. Improper electrical connections.

d. Faulty vacuum switch.

e. Faulty motor.f. Shut-down relay prevents pumping.

a. Adjust cam strap so clearance is.06 inches (1.5mm) maximum.

a. Replace water valve.

b. Insure that threads are not cross-threaded and tighten.

c. Replace water valve.d. Replace water valve.

a. Remove white cap from vacuumbreaker. Flush toilet. If water leaksduring flush, vacuum breakerneeds to be replaced.

b. Secure vacuum breakerconnection.

c. Replace toilet bowl.

a. Remove plastic base cover (onapplicable models) and tighten theclamp ring.

b. Replace ball seals.

a. Leave small amount of water inbowl. If water is sucked from bowl,see problems 1 and 2.

b. Tighten all connections at toilet,vacuum generator or vacuumholding tank (including hoseclamps and threaded spin nuts). Ifleaks persists, contact SeaLandProduct Customer Service.

a. See problem 9b.b. Isolate pump and use vacuum

gauge to check vacuum levels.Could be a plugged discharge lineor worn duckbill valves.

c. Replace vacuum switch.

d. Refer to wiring diagram to checkfor proper wiring.

e. Tighten set screw in eccentric tomotor shaft. Otherwise, check fordamage to bellows and motorshaft. Replace if necessary.

a. Check input power, circuit breakerand fuse.

b. Tighten or reconnect wires atvacuum pump and tank, vacuumgenerator, or vacuum holding tank.

c. Make certain wires at vacuumswitch are connected to the “B”terminals.

d. To check vacuum switch, shortacross “B” terminals with jumperwire.

e. Replace motor.f. Empty the holding tank.

Problem Possible Cause Service Instructions

TROUBLESHOOTING GUIDE

13.Vacuum pump is running tooslow, overheating, blowingfuses or circuit breaker.

14.Toilet will not flush.(No vacuum.)See problems 3 and 15if necessary.

15.Blockage between toilet andvacuum generator.

16.Pump emits odor.

a. Gear motor is worn or defective.

b. Plugged vent line or vent filter.

c. Blockage in discharge line.

d. Improper wire size.

e. Improper voltage.f. Vacuum pump bellows clogged

with tissue.

a. There is a blockage in the system.

b. Pump will not run.c. Duckbill valves in vacuum pump

are inverted due to blockeddischarge line or an attempt topump out against closed seacock.

a. Collapsed vacuum line.

b. Sharp bends or kinks in vacuumhose.

c. Improper operation of toilet.

d. Foreign objects were flushed downtoilet.

a. Loose or defective hoseconnection on pump.

b. Loose intake or discharge fittingson pump.

c. Worn, torn or punctured pumpbellows (vacuum generator) ordiaphragm (vacuum holding tank).

a. Check motor and replace ifnecessary.

b. Disassemble and clean out ventline. Replace vent filter ifnecessary.

c. Disassemble and clean dischargeline. Be certain that in-line valves(duckbill valves) and seacock arein proper position.

d. Wire size too small. Checkelectrical diagram for proper wiresize for voltage of pump used.

e. Check input power for low voltage.f. Remove and clean bellows

assembly. (When flushing toilet,using more water may alleviatethis problem.)

a. Open flush ball and check the 1-inch (25mm) orifice at the bottomof the base for blockage anddislodge it. Never use drain-opening or other householdplumbing chemicals.If blockage is not in base, it maybe found in these locations:• outlet of vacuum tank• inlet of vacuum generator• diptube of vacuum generator• inlet of vacuum pump

b. See problem 12.c. Replace duckbill valves, making

sure they point in the correctdirection.

a. Inspect vacuum line for collapsedcondition and replace line ifneeded.

b. Inspect vacuum hose for kinks orbends. If less than 8.5-inches(216mm) radius on any bend,reposition hose to achieveminimum 8.5-inch bend radius.

c. Make sure each person usingtoilet knows correct procedure.

d. DO NOT flush any non-dissolvingitems (i.e. sanitary napkins, facialtissue, wet strength tissue, papertowels, etc.) or excessive toilettissue down toilet. Rapid-dissolv-ing SeaLand brand toilet tissue isbest.

a. Tighten connections or replacehose and make new connections.

b. Tighten intake or discharge fittingson pump. Replace nipples oradapters if necessary.

c. Replace pump bellows ordiaphragm.

Problem Possible Cause Service Instructions

12

PARTS LISTMODEL 706

1

2

34*5

67891011

1213

1415

1617

Item Part No. Description385344436385344437385310676385310736385310048385316140385310132385310133385310064385318864600341549385310744385314349385310117385310118385318162600345377600340177385316906385310108385310109385236096385310696385310782

Seat Assembly, WhiteSeat Assembly, BoneChina Bowl, WhiteChina Bowl, BoneRing and Half Clamp KitTeflon® and Rubber Seal KitBase Kit, WhiteBase Kit, BoneMounting KitFunnel KitFloor Flange SealFlush Lever Kit (includes item 16)Water Valve KitPedal Cover Kit, WhitePedal Cover Kit, BoneBall, Shaft & Cartridge Kit (includes item 16)Supply Hose, WhiteSupply Hose, BoneVacuum Breaker KitPedestal Cover Kit, WhitePedestal Cover Kit, BoneSpring Cartridge AssemblyVacuum Breaker Cover, WhiteVacuum Breaker Cover, Bone

MODEL 1147 & 1148

1

2

34*5

6

78

9101112

13

14

Item

Seat Assembly, WhiteSeat Assembly, BoneChina Bowl, WhiteChina Bowl, BoneTeflon® & Rubber Seal KitBase RingBase Kit, Right-hand Discharge - WhiteBase Kit, Right-hand Discharge - BoneBase Kit, Rear Discharge - WhiteBase Kit, Rear Discharge - BoneMounting Kit, WhiteMounting Kit, BoneDischarge KitFlush Pedal Kit - White (includes item 10)Flush Pedal Kit - Bone (includes item 10)Water Valve KitSpring Cartridge KitBall, Shaft & Cartridge Kit (includes item 10)Ring & Half Clamp Kit, WhiteRing & Half Clamp Kit, BoneSupply Hose, WhiteSupply Hose, BoneVacuum Breaker Kit

Description

385340590385340591385310615385310616385310677600343534

385310686385310784385310679385310785385310680385310682385310786385314349385310683385310681385310025385310048600345377600340177385316906

Part No.

385340590385340591385310615385310616385310677600343534385310685385310783

385310679385310785385310680385310682385310786385314349385310683385310681385310025385310048600345377600340177385316906

1147 1148

* Includes items 3 through 12, 15 and 16.

* Includes items 3 through 12.

13

14

MODEL 506+ MODEL 508+

MODEL 547+ MODEL 548+

PARTS LIST

15

506+ 508+ 547+ 548+1

2

3456

78*9

10

111213

†14

15

16

ItemHushFlush Seat Assembly, WhiteHushFlush Seat Assembly, BoneHushFlush Seat Assembly, PlatinumHushFlush Seat Assembly, EbonyHushFlush Seat Assembly, TealChina Bowl Kit, WhiteChina Bowl Kit, BoneChina Bowl Kit, PlatinumChina Bowl Kit, EbonyChina Bowl Kit, TealRing & Half Clamp KitTeflon® & Rubber Seal KitMounting KitPedestal Cover Kit, WhitePedestal Cover Kit, BonePedestal Cover Kit, PlatinumPedestal Cover Kit, EbonyPedestal Cover Kit, TealFloor Flange SealFunnel KitBall/Shaft/Cartridge Kit, White/Bone/Plat.Ball/Shaft/Cartridge Kit, EbonyBall/Shaft/Cartridge Kit, TealPedal Cover Kit, WhitePedal Cover Kit, BonePedal Cover Kit, PlatinumPedal Cover Kit, EbonyPedal Cover Kit, TealWater Valve KitSpring Cartridge AssemblyFlush Lever Kit (includes item 13)Base Kit, WhiteBase Kit, BoneBase Kit, PlatinumBase Kit, EbonyBase Kit, TealSupply Hose, WhiteSupply Hose, BoneVacuum Breaker Kit

385343830385343832385343898385343902385343900385310739385310740385310741385310742385310743385310048385316140385310064385310108385310109385310110385310600385310603600341549385318864385318162385310177385310188385310117385310118385310119385310593385310596385314349385236096385310744385310943385310133385310134385310607385310610600345377600340177385316906

Description385343830385343832385343898385343902385343900385310739385310740385310741385310742385310743385310048385316140385316323385310111385310112385310113385310173385310203

NA385318741385318162385310177385310188385310114385310115385310116385310175385310193385314349385236096385310578385310126385310127385310128385310171385310213600345377600340177385316906

385343830385343832385343898385343902385343900385310739385310740385310741385310742385310743385310048385316140385316323385310674385310613385310745385310746385310747

NA385318741385318162385310177385310188385310114385310115385310116385310175385310193385314349385236096385310578385310665385310614385310748385310749385310750600345377600340177385316906

385343830385343832385343898385343902385343900385310739385310740385310741385310742385310743385310048385316140385316323385310136385310137385310138385310174385310223

NA385318741385318162385310177385310188385310114385310115385310116385310175385310193385314349385236096385310578385310129385310130385310131385310172385310218600345377600340177385316906

PARTS LIST

† Includes items 2 through 14.* Includes item 12.

16

MODEL 1006 MODEL 1008

MODEL 1047 MODEL 1048

PARTS LIST

17

1

2

34*5

67

89

101112

13

141516

ItemSeat Assembly, WhiteSeat Assembly, BoneSeat Assembly, EbonyChina Bowl Kit, WhiteChina Bowl Kit, BoneChina Bowl Kit, EbonyRing & Half Clamp KitTeflon® & Rubber Seal KitBase Kit, WhiteBase Kit, BoneBase Kit, EbonyMounting KitPedestal Cover Kit, WhitePedestal Cover Kit, BonePedestal Cover Kit, EbonyFunnel KitPedal Cover Kit, WhitePedal Cover Kit, BonePedal Cover Kit, EbonyWater Valve KitFlush Lever Kit (includes item 15)Ball/Shaft/Cartridge Kit, White/BoneBall/Shaft/Cartridge Kit, EbonySupply Hose, WhiteSupply Hose, BoneVacuum Breaker KitSpring Cartridge AssemblyFloor Flange Seal

Description385344436385344437385344438385310615385310616385310585385310048385316140385310132385310133385310607385310064385310108385310109385310600385318864385310117385310118385310593385314349385310579385318162385310177600345377600340177385316906385236096600341549

* Includes items 3 through 12 & 15.

1006 1008 1047 1048385344436385344437385344438385310615385310616385310585385310048385316140385310126385310127385310171385316323385310111385310112385310173385318741385310114385310115385310175385314349385310578385318162385310177600345377600340177385316906385236096

NA

385344436385344437385344438385310615385310616385310585385310048385316140385310129385310130385310172385316323385310136385310137385310174385318741385310114385310115385310175385314349385310578385318162385310177600345377600340177385316906385236096

NA

385344436385344437

385310615385310616

385310048385316140385310665385310614

385316323385310674385310613

385318741385310114385310115

385314349385310578385318162

600345377600340177385316906385236096

NA

PARTS LIST

18

NOTE: When reassembling pump, tighten screw (Item No. 7) , to 20 ±2 lbs., or until snug.Overtightening will cause holes to strip.

PARTS LIST

VACUUM GENERATOR

123456789

101112131415161718

600340237600343027600342804600341506600344087600342332600341503385310151600340664600343006600347807600342783600342779385310539600342782600342778385310540600347802

Pan Phillips Head Screw, #4 x 3/8", SSFlat Washer, .312" OD x .030 Thick, SSMotor/Switch CoverPump Top ClosureFlat Washer, #10 x 5/8" OD, SSHex Washer Head Screw, #10-32 x ½", SSHex Washer Head Screw, #10-12 x 7/8", SSO-Ring KitBushingShoulder Screw, ½ x .687 x 3/8-16Bellows Clamp3-3/4" Diameter Worm Gear ClampO-Ring, 3" ID x 3 ¼" ODDiptube Assembly Kit (includes item 13)2 ½" Diameter Worm Gear ClampO-Ring, 2" ID x 2-1/4" ODVacuum Switch Kit (includes items 15, 16)Duckbill Valve

19202122232425262728293031

31A32NSNS

600342789600342467600346795385310635600342932385310542600347800600347801600341504385230980600344470600347788385310245385310246600342798385310774385310775

1 ½" NPT Close Nipple¼-20 x ¾" Hex Head Screw, SSFlat Washer, .625" OD x .281" ID x .050Inlet Elbow Kit (includes item 23)1 ½" Uniseal®Vacuum Generator TankValve NippleValve AdapterPump BodyBellows Assembly (includes item 9)Pump Eccentric¼-28 x 5/16" Set Screw, ½ Dog Point12 VDC Motor Kit24 VDC Motor KitMounting SpindleKit, VG Pump Assembly, 12VDCKit, VG Pump Assembly, 24VDC

Item Part No. Description Item Part No. Description

19

PARTS LISTLOW-PROFILEVACUUM GENERATOR

Pan Phillips Head Screw, #4 x 3/8", SSPump CoverTop ClosureHex Washer Head Screw, #10-12 x 7/8", SSHex Washer Head Screw, #10-32 x ½", SSO-Ring Replacement KitBushingShoulder Screw, ½" x .687 x 3/8-16Bellows ClampValve NippleDuckbill ValveValve AdapterPump BodyPump FittingO-RingDiptube Kit – Low-Profile VGUniseal® 1½"Pan Phillips Head Screw, #4 x 1/4"

Part No.123456789101112131415161718

Item Description600340237385640239600341506600341503600342332385310151600340664600343006600347807600347800600347802600347801600341504600344676600343936600344675600342932600343621

Part No.Item Description192021222324

25262728

2929A

600343027600343913385310626600342798385310755385310635385310690385310787385230980600344470600347788385310756385310245385310757385310246600343053600343053

Washer, #6 x 3/8"Vacuum Switch CoverVacuum Switch KitMounting SpindlesLow-Profile Vacuum TankInlet Elbow AssemblyStraight Inlet (Optional)45° Inlet (Optional)Bellows AssemblyPump EccentricSet Screw, 1/4-28 x 5/16", ½ Dog Point12 VDC Motor w/ Deutsch Connection12 VDC Motor24 VDC Motor w/ Deutsch Connection24 VDC MotorRelay, SPDT 12 VDC 40/30 Amp, VF4Relay, SPDT 12 VDC 40/30 Amp, VF4

20

PARTS LIST

VACUUM PUMP, S-SERIES12345678910111213141516

16A17-

600340237385640239600341506600342332385310151600340664600343006600347807600347800385347802600347801600341504385230980600347788600344470385310245385310246600341503385310249

Cover Screw, #4 x 3/8" Pan Hd SSPump CoverTop ClosureHex Head Screw, #10-32 x ½" SSO-Ring Replacement KitBushing, BellowsHex Head Shoulder Screw, ½" x .687 x 3/8"-16Bellows ClampValve Nipple½" Duckbill Valve (2)Valve AdapterPump BodyBellows Assembly (incl. item 6)Set Screw, ¼ -28 x 5/16", ½" Dog PointEccentricMotor, 12VDCMotor, 24VDCHex Washer Head Screw #10-12 x 7/8", SSNot ShownPump Assembly Less Motor(Includes items 3, 5, 6, 8 through 13)

Item Part No. Description

NOTE: S-Series pump valve adapter and nipple (items 9 and 11)have right-hand threads (clockwise to tighten, counterclockwiseto loosen).

VACUUMTANK 1

234567

307341513307341161600348037385318032600346835600348361385310017

Insert AdapterStreet ElbowVacuum Switch CoverVacuum Switch AssemblySnap Lock ClampMounting BracketVacuum Tank Kit(Includes 2 each Item 1 and 1 each Item 2)

Item Part No. Description

123456789

600347800600347802600347839600341015385640116385230082600348702385640113385640115

308238696

308300011

Valve Nipple1 ½" Duckbill ValveValve AdapterHex Head ScrewPilot CollarMale Valve Housing Assembly2" Duckbill ValveFemale Valve HousingThreaded Collar

Small In-line Check Valve(includes items 1 through 3)Large In-line Check Valve(includes items 4 through 9)

Item Part No. DescriptionSMALL IN-LINE CHECK VALVE

LARGE IN-LINE CHECK VALVE

21

DIMENSIONAL SPECIFICATIONS

Toilet dimensions may vary ± 3/8-inch (10mm).

*

* Width measurement includes flush pedal.

*

*

22

WIRING DIAGRAMS

VACUUM PUMP

VACUUM GENERATOR

23

PARTS DISTRIBUTORSThere is a strong, worldwide network to assist in servicing andmaintaining your sanitation system. For the Authorized ServiceCenter near you, please call from 8:00 a.m. to 5:00 p.m. (ET)Monday through Friday. You may also write us at DometicCorp., P.O. Box 38, Big Prairie Ohio 44611.Telephone: 1 800-321-9886 U.S.A. and Canada

330-496-3211 International

You may also contact or have your local dealer contact theParts Distributor nearest you for quick response to yourreplacement parts needs. They carry a complete inventoryfor the SeaLand product line.

Fax: 330-496-3097 U.S.A. and Canada330-496-3220 International

U.S.A. - Southwest(AZ, CO, NV, UT, CA-south)Ardemco Marine Specialties778 West 17th StreetCosta Mesa, CA 92627Tel: 949-722-7672

800-253-0115Fax: 949-642-9582E-mail: ardemco@earthlink.netContact: Rick GlasserU.S.A. – Upper Midwest(IA, MN, NE, ND, SD, WI)PowerHouse Marine518 LoganLa Crosse, WI 54603Tel: 608-784-9580

888-752-4539Fax: 608-784-8422E-mail:dave@powerhousemarine.comContact: Dave TuckerU.S.A. – Northern CaliforniaFox Marine2250 Zanker Road, Unit DSan Jose, CA 95131Tel: 408-451-9055

800-826-2873E-mail: foxmarco@pacbell.netContact: Charlie Barker

INTERNATIONALDISTRIBUTORSArgentinaTrimer S.A.Del Arca 55, B1646 AASan FernandoPCIA, De Buenos AiresTel: 5411 4580 0444Fax: 5411 4580 0440E-mail: trimer@trimer.com.arContact: Carlos Friedlanderor Pablo VillarAustraliaDometic Pty Ltd6 Treforest DriveClayton, Victoria 3168PO Box 1140Clayton South, Victoria 3169Tel: (03) 9545 5655Fax: (03) 9545 5966Email:dometic@dometic.com.auContact: Petra BachAustriaOcean MarineSee GermanyBelgiumAuerhaan B.V.See The NetherlandsCanada - EastEastern Marine Systems, Inc.12-A Leslie StreetToronto, Ontario M4M 3H7Tel: 416-465-1668

888-764-1111Fax: 416-465-2098E-mail: info@eastmar.comContact: Paul Gales

Canada - WestWestern Marine Company1494 Powell StreetVancouver, BC V5L 5B5Tel: 604-253-7721

800-663-0600Fax: 604-253-2656

800-663-6790E-mail: sales@

westernmarine.comContact: Bill FalkCaribbeanBudget MarineP.O. Box 43425B Waterfront RoadCole Bay, PhilipsburgSt. MaartenNetherlands AntillesTel: 599 5 43134Fax: 599 5 44409Contact: Jackie LeechDenmarkDometic Origo ABSee SwedenFinlandNautikulma OyLantinen Pitkakatu 3320100 TurkuTel: 358 2 250 3444Fax: 358 2 251 8470E-mail: nautikulma@kolumbus.fiContact: Teppo SiltalaFranceKent Marine Equipment3 rue de la Dutee - BP 20744815 Saint-HerblainTel: 33 2 40 92 15 84Fax: 33 2 40 92 13 16Contact: Luc TavoliniGermanyOcean MarineWendenstrasse 42920537 HamburgTel: 49 (0) 40 219 1042Fax: 49 (0) 40 219 1114E-mail: info@ocean-marine.deContact: Thorsten LentzGreeceAmaltheia13 Papaflessa Str.143 43 N. HalkidonaAthens-GreeceTel: 30 (210) 25 88 985Fax: 30 (210) 25 88 986E-mail: amalmar@otenet.grContact: Dimitris KyriazesHong KongFuncle Ltd.G/F, 81D, Pak Shek TerraceClearwater Bay RoadSai KungTel: 852 2335 0482Fax: 852 2335 0580Contact: Alan Reid

ItalySVAMA Nautica s.r.l.Via Del Lavaro 25/A248015 Montaletto Di Cervia(Ravenna)Tel: 390 544 965689Fax: 390 544 965734E-mail: svama-nautica@

svama-nautica.comContact: Claudio CasadioJapanTominaga & Co., Ltd.2-6-8 NishitenmaKita-ku, Osaka 530Tel: 81 (06) 365 5010Fax: 81 (06) 365 6294E-mail: nishi@mail.tomco.jpContact: A. TatsumiLuxembourgAuerhaan B.V.See The NetherlandsThe NetherlandsAuerhaan B.V.P.O. Box 22, 8200 AA LelystadPlatinastraat 158211 AR, LelystadTel: 31 (0) 320-286171Fax: 31 (0) 320-286170E-mail: accessoires@

auerhaan.nlContact: Bert van LoenenNetherlands AntillesBudget MarineP.O. Box 43425B Waterfront RoadCole Bay, PhilipsburgSt. MaartenTel: 599 5 43134Fax: 599 5 44409Contact: Jackie LeechNew ZealandLusty & Blundell Ltd.38 Tawa DriveAlbany, AucklandTel: 64 (09) 415 8303Fax: 64 (09) 415 8304Contact: Mike HarrisNorwayDometic Origo ABSee SwedenPhilippinesSolid Sales Philippines31 Horseshoe DriveBanawa Hills, Cebu City 6000Tel: 63 32 255 3002Fax: 63 32 255 3001E-mail: ssphils@

cebu.pw.net.phContact: Andy Y. Lim

Sardenia and SicilySVAMA NauticaSee ItalySingaporeMarina Yacht Services Pte.Ltd.No. 10 Tuas West Drive#01-01 to 04 Raffles MarinaSingapore 638404Tel: 65 862 4320Fax: 65 862 4431Contact: Johnny LimSpain, Balearic & CanaryIslandsDahlberg Sociedad AnonimaNicolau de Pacs, 3207006 Palma de MallorcaTel: 34 971 774751Fax: 34 971 771458E-mail: sealand@

dahlberg-sa.comContact: Rosa DahlbergSwedenDometic Origo ABSöndrumsvägen 35SE-302 39 Halmstad, SwedenTel: 46 (0) 35 17 57 00Fax: 46 (0) 35 17 57 10E-mail: info@origo-sweden.comContact: Johan EdlundSwitzerlandOcean MarineSee GermanyTaiwanMercury Marine SupplyNo 488Ming Chuan 2nd RoadChyan Jenn District806 KaohsiungTel: 886 (07) 331 7293Fax: 886 (07) 332 4232E-mail: mms46654@

ms16.hinet.netContact: Mercury LiuTurkeyMarina Deniz AraclariFener Kalamis CAD. No:75Fenerbahce 81030IstanbulTel: 90 (0) 216 338 14 41Fax: 90 (0) 216 337 44 92E-mail: aylan@superonline.comContact: Isik AylanUnited KingdomLee SanitationFenny ComptonWharf Road, WarwickshireCV47 2FETel: 44 (0) 1295 770000Fax: 44 (0) 1295 770022E-mail: sales@leesan.comContact: Chris Coburn

U.S.A.MASTER SANITATIONDISTRIBUTORSU.S.A. – North Central(IL, IN, KY, MI, OH)Midwest Marine Supply24300 Jefferson Ave.St. Clair Shores, MI 48080Tel: 586-778-8950

800-860-1540Fax: 586-778-6108E-mail:midwestmarine@yahoo.comContact: Bob KennedyU.S.A. - Northeast(CT, DE, DC, MA, MD, ME, NH,NJ, NY, PA, RI, VA, VT, WV)Northeast Marine Sanitation69 Florida StreetFarmingdale, NY 11735Tel: 631-752-7606

800-352-4323Fax: 631-752-7615

888-283-7606E-mail: northeast@northeastsanitation.comContact: Mike StaritoU.S.A. - Northwest(AK, ID, MT, OR, WA, WY)Marine Sanitation, Inc.1900 N. Northlake Way, Suite 121Seattle, WA 98103Tel: 206-633-1110

800-624-9111Fax: 206-633-0317E-mail: marinesan@

mindspring.comContact: Ric KolbU.S.A. - South Central(AR, KS, LA, MO, MS, NM, OK,TX)AER SupplyP.O. Box 3492301 Nasa Road #1Seabrook, TX 77586Tel: 281-474-3276

800-767-7606Fax: 281-474-2714E-mail: rsmiller@aersupply.comContact: Richard MillerU.S.A. - Southeast(AL, FL, GA, NC, PR, SC, TN, VI)Environmental Marine111 S.W. 23rd Street, Suite AFort Lauderdale, FL 33315Tel: 954-522-2626

800-522-2656Fax: 954-522-5152E-mail:info@environmentalmarine.comContact: John or Jill Hopkins

24

MANUFACTURER’S ONE-YEAR LIMITED WARRANTYDometic Corporation warrants, to the original purchaser only, that this product, if used for personal, family or household-like purposes, and if installed according to Dometic’s recommended procedures, is free from defects in material andworkmanship for a period of one year from the date of purchase.

If this Dometic product is placed in commercial or business use, it will be warranted, to the original purchaser only, to befree of defects in material and workmanship for a period of ninety (90) days from the date of purchase.

Dometic reserves the right to replace or repair any part of this product that proves, upon inspection by Dometic, to bedefective in material or workmanship. All labor and transportation costs or charges incidental to warranty service are to beborne by the purchaser-user.

EXCLUSIONSIN NO EVENT SHALL DOMETIC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, FOR DAMAGESRESULTING FROM IMPROPER INSTALLATION OR IMPROPER OPERATION, OR FOR DAMAGES CAUSED BYNEGLECT, ABUSE, ALTERATION, USE OF UNAUTHORIZED COMPONENTS, OR IMPROPER WINTERIZATION. ALLIMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANYPARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OF ONE YEAR FROM DATE OF PURCHASE.

IMPLIED WARRANTIESNo person is authorized to change, add to, or create any warranty or obligation other than that set forth herein.

Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year fromthe date of purchase for products used for personal, family or household purposes, and ninety (90) days from the date ofpurchase for products placed in commercial or business use.

OTHER RIGHTSSome states do not allow limitations on the duration of an implied warranty and some states do not allow exclusions orlimitations regarding incidental or consequential damages; so, the above limitations may not apply to you. This warrantygives you specific legal rights, and you may have other rights which may vary from state to state.

To obtain warranty service, first contact your local dealer from whom you purchased this product.

® Registered; ™ Trademark of Dometic Corporation® Bar Keepers Friend is a registered trademark of SerVaas Laboratories.

® Teflon is a registered trademark of DuPont Co.® Uniseal is a registered trademark of Injection Plastics, Inc.

© Dometic Corporation600340066 8/03

Dometic Corporation • Sanitation Systems13128 State Rt. 226, P.O. Box 38Big Prairie, OH 44611-0038 USA

330-496-32111-800-321-9886 • Fax: 330-496-3097