SIRIUSi-XHS-PWR · 2020. 9. 17. · Image 6: DewesoftX® settings Adding a new XHS device is done by clicking +, this will show the Add device window where you can find a Real-time

SIRIUSi-XHS-PWR TECHNICAL REFERENCE MANUAL SIRIUSi-XHS-PWR V20-1

DEVICE TECHNICAL REFERENCE MANUAL

Table of contents

1. About this document 4 1.1. Legend 4 1.2. Online versions 5

1.2.1. SIRIUS-XHS-PWR technical reference manual 5 1.2.2. DewesoftX® tutorials 5

2. Getting started 6 2.1. Software installation 6 2.2. Connecting SIRIUSi-XHS-PWR 7

2.2.1. Network settings 8 2.2.1.1. Troubleshooting 8

2.2.2. DewesoftX® Settings SIRIUSi-XHS-PWR 9 2.2.3. Channel Setup SIRIUSi-XHS-PWR 15

2.3. Simple Measurement 16 2.3.1. Help - Manual 16 2.3.2. Analogue channel setup 17 2.3.3. Sample rate 17 2.3.4. Measurement Mode 18 2.3.5. Analyse Mode 18

2.4. Advanced configuration 19 2.5. Firmware upgrade 20 2.6. Licensing 21 2.7. Troubleshooting 22

3. System overview 23 3.1. Main features 24

3.1.1. Hybrid ADC technology 25 3.1.2. Perfect synchronization 25 3.1.3. Perfect amplifiers for power measurements 25 3.1.4. E-mobility power device 26 3.1.5. Open interface protocols 26 3.1.6. Power analyzer 26 3.1.7. Data Acquisition Software Included for Free 27

3.2. Dimensions 27 3.3. System specifications 28

4. Module overview 29 4.1. Voltage measurement 29

4.1.1. Voltage measurement: Specifications 29 4.2. Current measurements 30

4.2.1. Current measurement: Specifications 30

5. Safety instructions 31

SIRIUSi-XHS PWR V20-1 2/36


5.1. General Safety Instructions 31 5.1.1. Environmental Considerations 31 5.1.2. Product End-of-Life Handling 31 5.1.3. General safety and hazard warnings for all Dewesoft systems 31

6. Notice 34 6.1. Warranty Information 34 6.2. Calibration 34 6.3. Support 34 6.4. Service/repair 34 6.5. Restricted Rights 34 6.6. Printing History 35 6.7. Copyright 35 6.8. Trademarks 35 6.9. Documentation version 36



1. About this document This is the Technical Reference Manual for SIRIUSi-XHS-PWR Version V20-1 SIRIUS-XHS-PWR (SIRIUS-XHS-1xHV-1xDCCT) is a high performance, high speed line of SIRIUS® real time data acquisition hardware used for the most demanded power measurements, specially designed for E-mobility applications. Each system also includes a professional license for our award-winning DewesoftX® data acquisition software. The manual is divided into several chapters. You will find:

● A detailed description of the SIRIUS-XHS-PWR hardware ● A description of the mechanical connections and variants of current ranges ● A comprehensive introduction to the configuration of the modules using DewesoftX® ● Detailed technical data: Specifications, etc.

1.1. Legend The following symbols and formats will be used throughout the document.

Important Gives you important information about a subject. Please read carefully!

Hint Gives you a hint or provides additional information about a subject.

Example Gives you an example to a specific subject.

Safety symbols in the manual:

Warning Calls attention to a procedure, practice, or condition that could cause the body injury or death

Caution Calls attention to a procedure, practice, or condition that could possibly cause damage to equipment or permanent loss of data.



1.2. Online versions

1.2.1. SIRIUS-XHS-PWR technical reference manual The most recent version of this manual can be downloaded from our homepage: https://download.dewesoft.com/list/manuals-brochures/hardware-manuals In the Hardware Manuals section click the download link for the SIRIUSi-XHS-PWR technical reference manual.

1.2.2. DewesoftX® tutorials The DewesoftX® tutorials document, provides basics and additional information and examples for working with DewesoftX® and certain parts of the program. The latest version of the DewesoftX® tutorials can be found here: https://download.dewesoft.com/list/manuals-brochures/software-manuals In the Software Manuals section click the download link of the DewesoftX® tutorials entry.

Important Read safety instructions first in chapter 5. Safety instructions.


https://download.dewesoft.com/list/manuals-brochures/hardware-manualshttps://download.dewesoft.com/list/manuals-brochures/software-manuals


2. Getting started This chapter will help you to install the software, connect your SIRIUSi-XHS system to the PC via ethernet and will show you how to configure DewesoftX®. To follow these steps, you need the following items:

● your brand new SIRIUSi-XHS-PWR system (included in the shipment) ● your network cable (included in the shipment) ● your PC with Windows 10 (older versions like Windows® 7 may also work)

2.1. Software installation For optimal working, we recommend that you install the latest version of Dewesoft. If you already have installed the older version Dewesoft is recommended that you find the newest version on the website under Support/Downloads/DewesoftX section. You can also check if a newer version is available in software.

Image 1: Check for update



2.2. Connecting SIRIUSi-XHS-PWR In this chapter, you can see the basic instructions for connecting SIRIUSi-XHS-PWR devices. Advanced connections are described in the following chapters.

STANDALONE UNIT

Image 2: Connection of SIRIUSi-XHS-PWR standalone device to PC

PoE and MULTIPLE UNITS

Image 3: Connection of multiple SIRIUSi-XHS-PWR units to PC using PoE



2.2.1. Network settings SIRIUSi-XHS-PWR is a network device with static IP. The ethernet port on your SBOX, data logger or PC should be configured in a way to match the IP address of the SIRIUSi-XHS-PWR unit.

Example SIRIUSi-XHS-PWR has the IP address 192.168.10.1 Your network adapter should be set to: - IP: 192.168.10.x, where x is number from 2-255 - Subnet mask: 255.255.255.0

2.2.1.1. Troubleshooting If Dewesoft doesn’t detect your devices you should try pinging them via command prompt. In command prompt write: ping IP replace IP with IP that is set on your device. The result should be something like this:

Image 4: ping IP in Command Prompt



2.2.2. DewesoftX® Settings SIRIUSi-XHS-PWR SIRIUSi-XHS-PWR devices have static IP. When adding a new device open DewesoftX® and go to Options->Settings as shown in Image 5. Click on the Options button at the top right, and then on the Settings item in the pop-up to open the DewesoftX® settings dialogue.

Image 5: Settings



Image 6: DewesoftX® settings

Adding a new XHS device is done by clicking +, this will show the Add device window where you can find a Real-time controller. Sirius-XHS is an RT device so you should add it by clicking + on RT Device. If you want to use two devices you should add two.



Image 7: Adding RT device

Support of RT-devices is still an Experimental feature. If you do not see this option when adding a device, the option needs to be enabled under Advanced -> Experimental settings.



Image 8: Enable experimental feature

After that you will see a new Sirius XHS or Dewesof RT connection in the device tree.



Image 9: Two RT devices

If the text by the device is disconnected, you should click on the device (Dewesoft RT Connection) , set the correct IP and refresh.



Image 10: Setting IP

If everything is set correctly both devices should be detected as Sirius-XHS devices.



Image 11: Devices overview

Before measurement you need to set synchronization. This is done by selecting Local system and selecting time source as External, External (Clock provider) as PTP and Dewesoft DAQ Devices (Clock slave) as PTP.

Image 12: Setting synchronization



2.2.3. Channel Setup SIRIUSi-XHS-PWR In the channel setup you can see a preview of the connected devices on the left side.

When you click on a connector in the image the corresponding channel in the Channel setup grid will automatically be selected. This also works the other way around: when you select a channel (or multiple channels) in the setup grid, the corresponding connectors in the image will be highlighted.

The sampling rate will be set for all connected SIRIUSi-XHS-PWR units: of course only up to the max. sampling rate of the individual units. In channel setup mode you can set the wanted sample rate, range etc. and select channels you want to measure.

Image 13: Channel setup

2.3. Simple Measurement This chapter describes measurement basics, how to configure SIRIUSi-XHS-PWR and gives some details on the measurement setup.

2.3.1. Help - Manual Note that this document is just a quick start guide. For detailed information about DewesoftX® consult the Manual. To open the manual press the F1 button or click on the Options button and then select Manual from the pop-up menu.



Image 14: Help - Manual

When DewesoftX® has started up, you will be in Measure mode and see the Setup files list. Click on Ch. setup (on the right of Setup files) to switch to the Channel setup mode.

Image 15: Setup files

2.3.2. Analogue channel setup In the analogue channel setup screen you can see all channels of your connected SIRIUSi-XHS-1xHV-HA units. Per default only the first channel will be set to Used. Unused channels will not show up in measure mode and can thus not be used for display, calculations or storing: thus, we will also set the other channels to the used. Then you can click into the selected region to toggle Used/Unused for all channels at once. The selected channels will also be highlighted in the small preview image of the device. When you press the Setup button of a channel (the column at the right edge of the channel table – not shown in this screen-shot), you can change all the settings of the channel amplifier. You can also change the sample rate of the SIRIUSi-XHS-1xHV-HA.

2.3.3. Sample rate One of the most important settings is the sample rate. The sample rate defines how many data points, SIRIUSi-XHS-PWR will transfer to DewesoftX®. Higher sample rate also means that more data needs to be transferred via ethernet to your computer.



The sampling speed mainly depends on your application. To display your signal in a time domain with a good time resolution, you should sample 10 to 20 times faster than the frequency of the signal that you want to measure, e.g. 1 kS/s for a 50 Hz sine-wave. If you have a lot of high frequency components, it may be necessary to sample 100 times faster, e.g. 5 kS/s for the 50 Hz sine-wave, or even more. If you display only the frequency domain (FFT analysis), a 2.5 times faster sampling would be sufficient (125 S/s for the 50 Hz sine-wave). The higher the sampling rate, the better the time resolution. But also the file size will increase.

Image 16: Sample rate

2.3.4. Measurement Mode A click on Measure (at the right side of Ch. setup in Image 11) will take you to the Recorder screen measure mode where you can already see live data.

Hint When switching to Measure mode the data will not be stored automatically.

In measure mode you can have several measurement screens. DewesoftX® will create 2 default screens: Recorder and Custom but you can also create new screens or change the widgets of the existing screens as you like. The most important sections of the Measure mode: Recorder widget displays all your measurement channels. You can use the channel-selector list to assign measurement channels to the instruments. Each instrument has different settings. To start storing the data to a file, press the Store button. When you are done, press the Stop button to stop recording. Now DewesoftX® has created a datafile with all the data that you have seen during the recording session. You can now click the Analysis button (on the left-top of the screen to the right of the Measure button) to go to Analysis mode.

2.3.5. Analyse Mode When you have just stopped a measurement, DewesoftX® will automatically open the last recorded data file in Review mode, so that you can start the analysis right away.



Image 17: Analyse mode

The Review mode is much like the measurement mode. You will see the same measurement screens, the channel-selector list and the properties of the currently selected instrument. Differences are: (1) you have additional tool-buttons (2) there is a Signal overview window which will show you the whole data of one selected channel of the data file Now you can use the cursors to analyse your data, zoom in and out of the data, click Offline math to add computations based on your data, etc. You can also change the design of your measurement screens, print reports based on your data and export the data to other file formats for further analysis.

2.4. Advanced configuration Note, that the DewesoftX® launcher has already done the hardware setup for you – you can check this in the Settings dialogue. Click the Settings button (1) – and then click the Settings Menu item (2).



Image 18: Open settings dialogue

2.5. Firmware upgrade ● Download the Dewesoft upgrade package (.dxu file) from the Dewesoft downloads page under

the section Drivers. ● Copy the file into the Firmwares folder of your Dewesoft installation (e.g.

D:\DewesoftX\System\X3\Firmwares). ● Connect the Dewesoft instrument to the PC and run Dewesoft X3. ● Go to settings under the Update tab:

Image 19: Firmware update

● If the firmware package isn’t selected, select it by pressing the button and find the folder with

the firmware file in it.


https://download.dewesoft.com/list/drivers/firmware


● Select the device you want to upgrade and start the firmware upgrade by pressing the “Upgrade” button.

2.6. Licensing SIRIUSi-XHS-1xHV-HA or any other Dewesoft device already comes with an embedded Dewesoft license. You can check the license details with all the available options in the Licensing tab (1) by pressing the three dotted button (6). However if the user decides to upgrade the license with an additional extension, Dewesoft will require a new license registration. The registration can be made online (2) or offline by importing an offline license (5) in case the system doesn’t have an internet connection. Offline license can be pre-registered on a different PC with the internet connection. If needed, the license can also be written on the actual device (5). Active and embedded licenses are seen under Active licenses tab (5). If the license is recognized as none active, it usually means that the wrong license was entered.

Image 20: Licensing

All licenses regarding SIRIUSi-XHS-PWR will only work when the SIRIUSi-XHS-PWR system is connected to your PC and the device has been activated in the hardware setup.



2.7. Troubleshooting If your SIRIUSi-XHS-PWR device is not found by DewesoftX®:

● If you did not restart Windows after the software installation, restart now ● Make sure that you have started DewesoftX® version X3 SP12 or higher ● Make sure that the external power supply is connected and okay ● Disconnect the network cable and reconnect it. If this does not work, try to connect the network

cable to another Ethernet port of your PC ● Try to restart DewesoftX® ● Try to restart the PC



3. System overview

SIRIUS-XHS

Sirius XHS is the first device ever with Hybrid ADC technology capable of doing both high bandwidth transient recording and very high dynamic alias-free acquisition - software-selectable per channel.

Modern interfaces and protocols allow open and flexible connectivity.

Image 21: SIRIUSi XHS 1xHV1xDCCT device



3.1. Main features

● HYBRID ADC TECHNOLOGY: offers everything you ever wanted out of a high-end data acquisition device; software selectable per channel:

○ HIGH SAMPLING RATE HIGH BANDWIDTH: 15 MS/sec sampling rate captures even the shortest transients;

○ HIGH DYNAMIC ALIAS-FREE: Alias free filtering allows perfect acquisition of signals with up to 160 dB dynamic, similar performance than our best Dual-core Sirius, better than 24 bit.

● PERFECT SYNCHRONIZATION: even though users can select some channels to be high bandwidth and some to be alias-free, filtering is made in the way that all signals are perfectly time aligned with zero phase shift.

● MODERN DATA INTERFACES: GLAN interface allows the distribution of devices with PTPv2 synchronization; the USB3 interface allows the fastest data transfers with a quick connection to the computer.

● OPEN PROTOCOLS: data is transferred to any host using open OPC UA industry-standard protocol; in parallel the data is available over XCP protocol, allowing connection to ECU calibration software packages.

● HIGH ISOLATION: High channel-to-channel and channel-to-ground isolation prevents damage to the systems from excessive voltage and avoids ground loops.

● EXTREME CONDITIONS: SIRIUSi-XHS-1xHV-1xHA comes in ruggedized chassis and can withstand the harshest environmental conditions operating in temperature range from -40 °C to +80 °C. All the units are dust- and waterproof with IP67 rating.

● ADDITIONAL SAFETY: SIRIUSi-XHS-1xHV-1xHA includes digital interlock safety solution on the chassis covers and on the cabling. Additionally, multiple temperature sensors are distributed inside the chassis to monitor the temperature and to initiate shutdown in case of overheating.

● SOFTWARE INCLUDED WITH FREE LIFETIME UPGRADES: The easy-to-use but rich in functionality, award-winning DEWESoft X3 software is included. All upgrades to the software are free forever with no hidden licensing costs.



3.1.1. Hybrid ADC technology User can select for each channel two modes of operation:

a) High bandwidth mode: with more than 3 MHz bandwidth and 15 Ms/sec sampling rate, XHS can perfectly acquire impulse, step and square signals without any ringing or overshoot. Such a mode is perfect for transient recording and power analysis. Such acquisition mode is typically in SAR ADCs.

b) Alias free mode: up to 1 Ms/sec data can be acquired with extremely high dynamic, similar to our dual 24 bit SIRIUS dual-core. The data is totally alias-free, so all higher frequencies are fully rejected. Such a mode is perfect for sound, vibration, and general data recording applications. Such acquisition mode is typically in Sigma-Delta ADCs.

Usually, you would need two totally separate devices for the above-mentioned applications. But on SIRIUS XHS you can select channel per channel, depending on the application, the appropriate mode of ADC operation.

3.1.2. Perfect synchronization If you mix channels from Sigma-Delta and SAR devices (high bandwidth and alias-free), then channels are delayed due to SIgma-delta filtering group delay. But with SIRIUS XHS, due to the nature of the chosen filter, both modes are perfectly aligned and synchronized. As on any Dewesoft devices, data can be synchronized to other data sources, such as vehicle bus interface, GPS, IMU, video, and others. Devices can be synchronized between each other using PTPv2 mechanism, IRIG or PPS signal. This also provides absolute time synchronization using in-house time servers or GPS.

3.1.3. Perfect amplifiers for power measurements SIRIUS XHS HV: Highly isolated CATII 1000 V, from 200 V to 2000 V range, >3 MHz bandwidth with down to 0.03% accuracy, this device is perfect for direct connection of high voltage signal. SIRIUS XHS HA: DCCT technology, up to 1000 A range, >500 kHz bandwidth, with down to 0.01% gain linearity, this device is perfect for direct connection to the in-vehicle high current lines.



3.1.4. E-mobility power device The SIRIUS XHS 1xHV,1xDCCT device is well suited for in-vehicle measurements. In-built patented DC-CT current transducer allows very precise current measurements even in most demanding applications such as very high current peaks as well as the leakage current measurement. The device is perfect to be installed in a vehicle directly in the power lines. Its IP67 protection allows the usage in harsh environments.

3.1.5. Open interface protocols

In today’s world of open toolchain and intercommunication, each device should be compliant with standard protocols. All protocols can be used at the same time. OPC UA: is the industry standard. Actually, it is more than a standard, it is a perfect framework where the device can be described and set up in any system, including SCADA, MES, ERP, mobile devices and others. XCP: Starting with version 1.4., XCP became a very powerful interface protocol in the automotive industry for data exchange. In the modern age of e-mobility, the required sampling rates are much higher than ever and 1 GBIT XCP interface allows data transfers with as high as 5 Ms/sec. CAN/CAN FD: Vehicle bus systems can be read through the CAN FD interface while the measured data can be also transmitted through this “golden” standard protocol.

3.1.6. Power analyzer

Dewesoft software will automatically calculate and store not only raw data from the voltage and current transducers but also all the power parameters: P, Q, S, D, Cos φ, power factor, P, Q, cos φ for each harmonic and other relevant power parameters. Each parameter can visually be displayed in a time recorder, digital or analog display. Using a computer graphics card as a multi-threaded calculation platform, the Dewesoft power module can calculate all those parameters up to a full speed of 15 Ms/sec.



3.1.7. Data Acquisition Software Included for Free

All Dewesoft data acquisition systems are bundled with award winning Dewesoft X Professional DAQ software. Dewesoft X is the world's most advanced and easy-to-use data acquisition and analysis software. Dewesoft X's flexibility and power will help you unleash the DAQ system to its full potential and gives you many advantages over other DAQ systems. Functionalities like plug-and-play, hardware auto-detection, smart TEDS sensors, advanced storing and data analysis features will take your measurement and analysis needs to a whole new level.

3.2. Dimensions TECHNICAL DRAWING

Image 22: Dimensions



3.3. System specifications

Power

Power supply

9 - 36 V DC PoE (RJ45) PWR IN (Lemo 1B 2-pin)

Power consumption Typ. 30 W

Environmental

Operating Temperature -40 to 70 °C

Storage Temperature -40 to 85 °C

IP rating IP67

Shock & Vibration TBD

Interfaces

Ethernet GbE (XCP, OPC UA) incl. IEEE1588v2 synchronization (PTP) (RJ45)

CAN CAN-FD, CAN 2.0 (DSUB9)

Sync Input / Output

Level (Input/Output) TTL compatible

Max. Output Current ±24 mA (±50 mA for 1 sec)

Max. Sync-cable length 100 m (Master/Slave), 200 m (IRIG)

Additional Specifications

Interlock YES (chassis covers + cables)



4. Module overview

4.1. Voltage measurement

KEY FEATURES

● Sampling rate: 15 MS/sec ● Input voltage ranges: ±2000 V ... ±20 V ● AAF: 1 MHz, 6th order ● Bandwidth: 3 MHz ● Input impedance: 10 MΩ ● Isolation: CATII 1000V

4.1.1. Voltage measurement: Specifications Inputs Voltage

ADC Type HybridADC - 24 bit alias free up to 1 MS/sec, 16 bit up to 15 MS/sec

Sampling Rate Simultaneous 15 MS/sec

Filtering AAF 1MHz (6th order Butterworth)

Analogue bandwidth > 3MHz

Voltage ranges ±2000 V, ±1000 V, ±400 V, ±200 V, ±100 V, ±40 V, ±20 V

Input Accuracy Signal frequency Accuracy

DC ±0.03% of reading ±0.02% of range ±0.04V

Up to 1kHz ±0.03% of reading ±0.02% of range

Up to 10 kHz ±0.1% of reading ±0.05% of range

Up to 100 kHz ±2% of reading ±0.1% of range

Up to 1000 kHz ±5% of reading ±0.5% of range

Voltage range ±2000 V Filter OFF Filter ON

Typ. Noise floor @ 15 MS/sec / 1 MS/sec / 10kHz 81 dB / 92dB / 103 dB 87 dB / 97 dB / 108 dB

Typ. CMR @ 50 Hz/1 kHz/10 kHz TBD

Channel Crosstalk @ 50 Hz/1 kHz TBD

Gain Drift Typical 10 ppm/K, max. 40 ppm/K

Offset Drift Typical 1 mV/K + 1 ppm of range/K, max 2 mV/K + 5 ppm of range/K

Gain Linearity


4.2. Current measurements

KEY FEATURES

● Zero-flux transducer ● Measurement of residual current in core ● High accuracy ● High bandwidth ● Low noise ● Temperature stability ● Low power consumption

4.2.1. Current measurement: Specifications

Inputs Current

ADC Type HybridADC - 24 bit alias free up to 1 MS/sec, 16 bit up to 15 MS/sec

Sampling Rate Simultaneous 15 MS/sec

Filtering AAF 1MHz (6th order Butterworth)

Current Ranges 1000 A 500 A 100 A

Sensitivity 4 mV/A 8 mV/A 40 mV/A

Recommended cable size 95 mm2 50 mm2 25 mm2

Recommended PG cable gland M32 M25 M16

Recommended grounding cable size 50 mm2 25 mm2 16 mm2

Offset Accuracy ± 50 mA

Gain linearity < 0.01%



5. Safety instructions Your safety is our primary concern! Please be safe!

5.1. General Safety Instructions

Warning

The following general safety precautions must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the product. Dewesoft d.o.o. assumes no liability for the customer’s failure to comply with these requirements. All accessories shown in this document are available as an option and will not be shipped as standard parts.

5.1.1. Environmental Considerations Information about the environmental impact of the product.

5.1.2. Product End-of-Life Handling Observe the following guidelines when recycling a Dewesoft system: System and Components Recycling Production of these components required the extraction and use of natural resources. The substances contained in the system could be harmful to your health and to the environment if the system is improperly handled at its end of life! Please recycle this product in an appropriate way to avoid an unnecessary pollution of the environment and to keep natural resources.

This symbol indicates that this system complies with the European Union’s requirements according to Directive 2002/96/EC on waste electrical and electronic equipment (WEEE). Please find further information about recycling on the Dewesoft web site www.dewesoft.com

Restriction of Hazardous Substances This product has been classified as Monitoring and Control equipment and is outside the scope of the 2002/95/EC RoHS Directive. However, we take care of our environment and the product is lead-free.

5.1.3. General safety and hazard warnings for all Dewesoft systems Safety of the operator and the unit depend on following these rules.


http://www.dewesoft.com/


● Use this system under the terms of the specifications only to avoid any possible danger. ● Read your manual before operating the system. ● Observe local laws when using the instrument. ● DO NOT touch internal wiring! ● DO NOT use higher supply voltage than specified! ● Use only original plugs and cables for harnessing. ● You may not connect higher voltages than rated to any connectors. ● The power cable and connector serve as Power-Breaker. The cable must not exceed 3 meters,

the disconnect function must be possible without tools. ● Maintenance must be executed by qualified staff only. ● During the use of the system, it might be possible to access other parts of a more

comprehensive system. Please read and follow the safety instructions provided in the manuals of all other components regarding warning and security advice for using the system.

● With this product, only use the power cable delivered or defined for the host country. ● DO NOT connect or disconnect sensors, probes or test leads, as these parts are connected to a

voltage supply unit. ● Ground the equipment: For Safety Class 1 equipment (equipment having a protective earth

terminal), a non-interruptible safety earth ground must be provided from the mains power source to the product input wiring terminals.

● Please note the characteristics and indicators on the system to avoid fire or electric shocks. Before connecting the system, please read the corresponding specifications in the product manual carefully.

● The inputs must not unless otherwise noted (CATx identification), be connected to the mains circuit of category II, III and IV.

● The power cord separates the system from the power supply. Do not block the power cord, since it has to be accessible for the users.

● DO NOT use the system if equipment covers or shields are removed. ● If you assume the system is damaged, get it examined by authorized personnel only. ● Adverse environmental conditions are Moisture or high humidity Dust, flammable gases, fumes

or dissolver Thunderstorm or thunderstorm conditions (except assembly PNA) Electrostatic fields, etc.

● The measurement category can be adjusted depending on module configuration. ● Any other use than described above may damage your system and is attended with dangers like

short-circuiting, fire or electric shocks. ● The whole system must not be changed, rebuilt or opened. ● DO NOT operate damaged equipment: Whenever it is possible that the safety protection

features built into this product have been impaired, either through physical damage, excessive moisture, or any other reason, REMOVE POWER and do not use the product until the safe operation can be verified by service-trained personnel. If necessary, return the product to Dewesoft sales and service office for service and repair to ensure that safety features are maintained.

● If you assume a more riskless use is not provided anymore, the system has to be rendered inoperative and should be protected against inadvertent operation. It is assumed that a more riskless operation is not possible anymore if the system is damaged obviously or causes strange noises. the system does not work anymore. the system has been exposed to long storage in adverse environmental. the system has been exposed to heavy shipment strain.

● Warranty void if damages caused by disregarding this manual. For consequential damages, NO liability will be assumed!



● Warranty void if damage to property or persons caused by improper use or disregarding the safety instructions.

● Unauthorized changing or rebuilding the system is prohibited due to safety and permission reasons (CE).

● Be careful with voltages >25 VAC or >35 VDC! These voltages are already high enough in order to get a perilous electric shock by touching the wiring.

● The product heats during operation. Make sure there is adequate ventilation. Ventilation slots must not be covered!

● Only fuses of the specified type and nominal current may be used. The use of patched fuses is prohibited.

● Prevent using metal bare wires! Risk of short circuit and fire hazard! ● DO NOT use the system before, during or shortly after a thunderstorm (risk of lightning and high

energy over-voltage). An advanced range of application under certain conditions is allowed with therefore designed products only. For details, please refer to the specifications.

● Make sure that your hands, shoes, clothes, the floor, the system or measuring leads, integrated circuits and so on, are dry.

● DO NOT use the system in rooms with flammable gases, fumes or dust or in adverse environmental conditions.

● Avoid operation in the immediate vicinity of high magnetic or electromagnetic fields, transmitting antennas or high-frequency generators, for exact values please refer to the enclosed specifications.

● Use measurement leads or measurement accessories aligned with the specification of the system only. Fire hazard in case of overload!

● Do not switch on the system after transporting it from a cold into a warm room and vice versa. The thereby created condensation may damage your system. Acclimatise the system unpowered to room temperature.

● Do not disassemble the system! There is a high risk of getting a perilous electric shock. Capacitors still might be charged, even if the system has been removed from the power supply.

● The electrical installations and equipment in industrial facilities must be observed by the security regulations and insurance institutions.

● The use of the measuring system in schools and other training facilities must be observed by skilled personnel.

● The measuring systems are not designed for use in humans and animals. ● Please contact a professional if you have doubts about the method of operation, safety or the

connection of the system. ● Please be careful with the product. Shocks, hits and dropping it from already- lower level may

damage your system. ● Please also consider the detailed technical reference manual as well as the security advice of the

connected systems. ● This product has left the factory in safety-related flawless and in proper condition. In order to

maintain this condition and guarantee safety use, the user has to consider the security advice and warnings in this manual.



6. Notice The information contained in this document is subject to change without notice. Note: Dewesoft d.o.o. shall not be liable for any errors contained in this document. Dewesoft MAKES NO WARRANTIES OF ANY KIND WITH REGARD TO THIS DOCUMENT, WHETHER EXPRESS OR IMPLIED. DEWESOFT SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Dewesoft shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any other legal theory, in connection with the furnishing of this document or the use of the information in this document.

6.1. Warranty Information The copy of the specific warranty terms applicable to your Dewesoft product and replacement parts can be obtained from your local sales and service office. To find a local dealer for your country, please visit https://dewesoft.com/support/distributers. 6.2. Calibration Every instrument needs to be calibrated at regular intervals. We recommend annual calibration. Before your Dewesoft data acquisition system is delivered, it is calibrated. Detailed calibration reports for your Dewesoft system can be requested. We retain them for at least one year, after system delivery. 6.3. Support Dewesoft has a team of people ready to assist you if you have any questions or any technical difficulties regarding the system. For any support please contact your local distributor first or Dewesoft directly. E-mail: [email protected] Address: Dewesoft d.o.o. Gabrsko 11a 1420 Trbovlje Slovenia Europe Tel.: +386 356 25 300 Web: http://www.dewesoft.com The telephone hotline is available Monday to Friday from 07:00 to 16:00 CET (GMT +1:00)

6.4. Service/repair The team of Dewesoft also performs any kinds of repairs to your system to assure a safe and proper operation in the future. For information regarding service and repairs please contact your local distributor first or Dewesoft directly on https://dewesoft.com/support/rma-service.

6.5. Restricted Rights Use Slovenian law for duplication or disclosure. Dewesoft d.o.o. Gabrsko 11a, 1420 Trbovlje, Slovenia / Europe.


https://dewesoft.com/support/distributersmailto:[email protected]://www.dewesoft.com/https://dewesoft.com/support/rma-service


6.6. Printing History Version 1.0.0 Released 2020 Last changed: 17/09/2020 at 07:00. 6.7. Copyright Copyright © 2015-2020 Dewesoft d.o.o. This document contains information which is protected by copyright. All rights are reserved. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. All trademarks and registered trademarks are acknowledged to be the property of their owners. 6.8. Trademarks We take pride in our products and we take care that all key products and technologies are registered as trademarks all over the world. The Dewesoft name is a registered trademark. Product families (KRYPTON, SIRIUS, DSI, DS-NET, IOLITE) and technologies (DualCoreADC, SuperCounter, GrandView) are registered trademarks as well. When used as the logo or as part of any graphic material, the registered trademark sign is used as a part of the logo. When used in text representing the company, product or technology name, the ® sign is not used. The Dewesoft triangle logo is a registered trademark but the ® sign is not used in the visual representation of the triangle logo.



6.9. Documentation version

Doc-Version Date [dd.mm.yyyy]

Notes

1.1.0 17.09.2020 Initial version


Documents

SIRIUSi-XHS-PWR · 2020. 9. 17. · Image 6: DewesoftX® settings Adding a new XHS device is done by clicking +, this will show the Add device window where you can find a Real-time