Upload
others
View
11
Download
1
Embed Size (px)
Citation preview
green energy so lu t ions
WP-GI Galvanic Isolation-transformer Transformer for safety and hull protection to prevent corrosion Commercial vehicles • Marine applications • Industrial systems
Datasheet
- Safety by galvanic isolation of AC power- Prevention of galvanic corrosion- Low noise, low weight toroidal transformer with vibration isolated mounting to eliminate noise- Softstarter integrated- Double the power by parallel function (WP-GI 7000)
WP-GI 3600 • WP-GI 7000The Whisperpower Isolation-transformer is used to create a safe AC net on board or on the vehicle. On boats,
the ground loop is broken with this Isolation-transformer, which prevents galvanic corrosion of the metal parts.
A separate galvanic isolator is not needed. A soft-starter is integrated and necessary to prevent input surge
currents on the AC input. The unit is built according CE, UL and ABYC guidelines. Easy and independent selection
of input and output voltage: 230V or 110V and 110V dual phase. In all operation modes, the full specified power
is available. The AC output is floating or can be polarized depending on local regulations. In case the ship is in
dry dock, a temporary connection of protective earth (PE) between primary and
secondary side can easily be made inside the connection compartment.
Optional:Option to mount ground fault circuit interrupter in connection compartment
Article nr. 60110100 WP-GI 3600 Galvanic Isolation-transformerArticle nr. 60110300 WP-GI 7000 – 2 units WP-GI 3600 for parallel useApplication Galvanic Isolation-transformer for safety and protection of galvanic corrosion
Transformer type 2 winding toroidal isolation transformer
Construction method Special vibration isolated mounting of transformer
Cooling method Temperature controlled gradually regulated forced air cooling above 60° transformer core
Winding Data WP-GI 3600 WP-GI 7000 Rated power 3.6kVA 7.0kVA
Rated voltage 230V / 110V 230V / 110V
Rated frequency 50Hz / 60Hz 50Hz / 60Hz
Nominal current 16A / 32A 30A / 60A
Inrush current Softstart included <4A per unit
Tappings Prim/sec. mid-point (110VAC)
Material winding Copper
Temperature rise class Class F 100 K
Insulation class Class H 180 C
Insulation level Class AC3
Impedance Secundary less than 3.0% at 3.6kVA
General No load consumption 21W per unit
Full load efficiency >95%
Ambient operating temperature -10°C .. +45°C, derating to 80°C
Storage temperature -25°C to 85°C
Operating humidity 95% max, non-condensing
Audible noise <40.0 dB(A); <50dB(A) with forced cooling
Local user interface None
Protections Overcurrent, short circuit Not included, external breaker(s) required according to local regulations
Temperature protection Automatic switch off if transformer core > 120°C
Overvoltage protection Softstart is protected for overvoltage using fuse
Earthscreen between windings Compliant to ABYC, can carry full fault current
Safety Standards IEC 60079, IEC 60726
Mechanical Protection degree IP21
Connections input/output 6mm2 max.
Cable gland entry 22mm
Dimensions (HxWxD) 510x330x150 per unit
Mounting holes M10
Weight 28.6 kg per unit
Enclosure construction Steel sheet metal
Surface finishing RAL9003 structure powder coating
Optional Article nr.: It is recommended to install a GFCI/RCD in the AC input line.
60110105 WP-GI Replacement cover with DIN-rail mount
50214640 Shore power circuit breaker 16A / 230V-1ph-3 wire
50214641 Shore power circuit breaker 25A / 230V-1ph-3 wire
50214642 Shore power circuit breaker 35A / 230V-1ph-3 wire
50214645 WP-Energy Meter 1P+N 65A DIN-rail mount
g reen energy so lu t ions
2609
2013
data
shee
tWP-
GI
WhisperPower BV Kelvinlaan 82, 9207 JB Drachten, The NetherlandsTel: +31 (0) 512 571 550, Fax: +31 (0) 512 571 [email protected], www.whisperpower.com
Galvanic Isolation-transformer
WP-GIWhisper Power Galvanic
Isolation-transformerTransformer for safety and hull protection to prevent corrosion
115
230VAC 230VAC
SHOREPE
N
L
PE
N
L
SHIP
115
115
115
ACin ACout
C
2 31 4
B
A
D
E
Material <not specified>Material:
NAME
16-2-2012J.R.
FINISH:
DRAWING:
TOLERANCE PRINCIPEISO 8015
21-9-2012
Weight: 12.26 gram
-
SHEET 1 OF 1SCALE:1:1
ARTICLE NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
STATUS:DATESIGNATURE
UNLESS OTHERWISE SPECIFIED:CHAMFER SHARP EDGESGENERAL TOLERANCENEN ISO 2768-mFORM AND PLACE TOLERANCES NEN-ISO 1101WELDING SYMBOL NEN EN 22553ROUGHNESS ACC. to NEN3634
CHK'D
DRAWN
Phoenix
PRINTED 21-9-2012
M.B.
SHEET FORMAT:PROJECTION : THIRD ANGLEUNITS : mm A4
C
23 14
B
A
D
E
Material <not specified>Material:
NAME
16-2-2012 J.R.
FINISH:
DRAWING:
TOLERANCE PRINCIPEISO 8015
21-9-2012
Weight: 12.26 gram
-
SHEET 1 OF 1 SCALE:1:1
ARTICLE NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
STATUS: DATE SIGNATURE
UNLESS OTHERWISE SPECIFIED:CHAMFER SHARP EDGESGENERAL TOLERANCENEN ISO 2768-mFORM AND PLACE TOLERANCES NEN-ISO 1101WELDING SYMBOL NEN EN 22553ROUGHNESS ACC. to NEN3634
CHK'D
DRAWN
Phoenix
PRINTED21-9-2012
M.B.
SHEET FORMAT:PROJECTION : THIRD ANGLEUNITS : mmA4
LNPE
LNPE
NC
Main Input Power Disconnect Circuit
Breaker with GroundFault Protection
Ground lug
Ground lug
2 x Galvanic Isolation-transformer
115
230VAC 230VAC
SHOREPE
N
L
PE
N
L
SHIP
115
115
115
115
230VAC 230VAC
SHOREPE
N
L
PE
N
L
SHIP
115
115
115
ACin
ACin
ACout
ACoutC
2 31 4
B
A
D
E
Material <not specified>Material:
NAME
16-2-2012J.R.
FINISH:
DRAWING:
TOLERANCE PRINCIPEISO 8015
21-9-2012
Weight: 12.26 gram
-
SHEET 1 OF 1SCALE:1:1
ARTICLE NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
STATUS:DATESIGNATURE
UNLESS OTHERWISE SPECIFIED:CHAMFER SHARP EDGESGENERAL TOLERANCENEN ISO 2768-mFORM AND PLACE TOLERANCES NEN-ISO 1101WELDING SYMBOL NEN EN 22553ROUGHNESS ACC. to NEN3634
CHK'D
DRAWN
Phoenix
PRINTED 21-9-2012
M.B.
SHEET FORMAT:PROJECTION : THIRD ANGLEUNITS : mm A4
C
2 31 4
B
A
D
E
Material <not specified>Material:
NAME
16-2-2012J.R.
FINISH:
DRAWING:
TOLERANCE PRINCIPEISO 8015
21-9-2012
Weight: 12.26 gram
-
SHEET 1 OF 1SCALE:1:1
ARTICLE NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
STATUS:DATESIGNATURE
UNLESS OTHERWISE SPECIFIED:CHAMFER SHARP EDGESGENERAL TOLERANCENEN ISO 2768-mFORM AND PLACE TOLERANCES NEN-ISO 1101WELDING SYMBOL NEN EN 22553ROUGHNESS ACC. to NEN3634
CHK'D
DRAWN
Phoenix
PRINTED 21-9-2012
M.B.
SHEET FORMAT:PROJECTION : THIRD ANGLEUNITS : mm A4
C
23 14
B
A
D
E
Material <not specified>Material:
NAME
16-2-2012 J.R.
FINISH:
DRAWING:
TOLERANCE PRINCIPEISO 8015
21-9-2012
Weight: 12.26 gram
-
SHEET 1 OF 1 SCALE:1:1
ARTICLE NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
STATUS: DATE SIGNATURE
UNLESS OTHERWISE SPECIFIED:CHAMFER SHARP EDGESGENERAL TOLERANCENEN ISO 2768-mFORM AND PLACE TOLERANCES NEN-ISO 1101WELDING SYMBOL NEN EN 22553ROUGHNESS ACC. to NEN3634
CHK'D
DRAWN
Phoenix
PRINTED21-9-2012
M.B.
SHEET FORMAT:PROJECTION : THIRD ANGLEUNITS : mmA4
C
23 14
B
A
D
E
Material <not specified>Material:
NAME
16-2-2012 J.R.
FINISH:
DRAWING:
TOLERANCE PRINCIPEISO 8015
21-9-2012
Weight: 12.26 gram
-
SHEET 1 OF 1 SCALE:1:1
ARTICLE NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
STATUS: DATE SIGNATURE
UNLESS OTHERWISE SPECIFIED:CHAMFER SHARP EDGESGENERAL TOLERANCENEN ISO 2768-mFORM AND PLACE TOLERANCES NEN-ISO 1101WELDING SYMBOL NEN EN 22553ROUGHNESS ACC. to NEN3634
CHK'D
DRAWN
Phoenix
PRINTED21-9-2012
M.B.
SHEET FORMAT:PROJECTION : THIRD ANGLEUNITS : mmA4
LNPE
LNPE
LNPE
LNPE
NC
NC
Main Input Power Disconnect Circuit
Breaker with GroundFault Protection
Main Input Power Disconnect Circuit
Breaker with GroundFault Protection
Single use (WP-GI 3600)
Parallel use (WP-GI 7000)