7

Click here to load reader

Build a Low Cost & Simple Magnetic Pulser - Share the Wealth

Embed Size (px)

Citation preview

Page 1: Build a Low Cost & Simple Magnetic Pulser - Share the Wealth

Share The Wealth by Chris GuptaSelf-Sufficiency Is The Key To Empowerment And Freedom

August 19, 2003

Build a Low cost & simple Magnetic Pulser

Categories

Electromedicine (http://www.newmediaexplorer.org/chris/electromedicine.htm)

Practical Health (http://www.newmediaexplorer.org/chris/practical_health.htm)

Finally, at long last here is an extensive update (of the 2003-08-19 original) that many have

been requesting. Some additions are:

- Basic 220/240 Volt AC Circuit.

- A Simple auto pulsing Circuit.

- 12 V DC Operation

- High Power vs low power - discussion

- Polarity of Coil.

- Various other embellishments and updates - that should address many questions in the

comments

- Pictures of the Original Device.

- Sites of interest.

The full Beck protocol must be followed for the pulser to be effective.... Additionally the Blood

electrifier should be modified with an extra battery as this has been found to be better with due

to variations in skin thicknesses.

You can access the full Beck protocol via:

Build Your Own, For Almost Free, Electromedical Research Devices(http://www.newmediaexplorer.org/chris/2006/10

/25/build_your_own_for_almost_free_electromedical_research_devices.htm) . Please read related links

in this post also.

"...The sicker a person is the more nutrients are needed in optimum doses to help the bodies

reparative mechanisms..." (http://www.newmediaexplorer.org/chris/2003/07/04/stale_food_vs_fresh_food_a_banned_book.htm)

Stop all processed foods (this includes all vegetable oils (unrefined cold pressed oils such

as organic Fax, olive (uncooked only) for salads, coconut and palm for cooking are the only

exceptions) and most milk products, unless raw, rest are all adulterated. No breads unless

cultured and made from stone ground grains! - Best to reduce carbohydrates and especially salt

(but increase raw and cooked organic vegetables) and no artificial sweeteners. If you want a

little sweetener go to totally unprocessed ones such as little unpasteurized honey and cane

sugar. Take a little lugols iodine (http://www.newmediaexplorer.org/chris/2007/01

/31/consequences_of_iodine_deficiency.htm) say a drop or two a day - don't overdo it.

Also note: dehydrated patients may not respond well to any type of therapy! Nearly all water

has toxins in it! (http://www.newmediaexplorer.org/chris/2008/01

/28/water_toxicity_hydrofluorosilicic_acid.htm) Best to use distilled to which a little magnesium(http://www.newmediaexplorer.org/chris/2005/09

/15/magnesium_chloride_in_acute_and_chronic_diseases.htm) has been added. Better to make herbal

teas and/or drink fresh vegetable fruit juices

WARNING: This is an experimental device and uses 110/220/240 Volt AC mains

voltage, build at your own peril. If not comfortable, have a someone familiar with

electronics like a TV repairman build it for you.

Magnetic Pulser: Dr Bob Beck PROTOCOL - short 8 minute video: (http://www.youtube.com/watch?v=rMeFHp36WNo)

Build a Low cost & simple Magnetic Pulser - Share The Wealth http://www.newmediaexplorer.org/chris/2003/08/19/build_a_low_cost_...

1 of 7 2/2/2011 1:36 PM

Page 2: Build a Low Cost & Simple Magnetic Pulser - Share the Wealth

()

Well finally, I have got all the wrinkles out my prototype SCR Thumpy. And this circuit has

definitely got the power. You can actually feel an electric current pulse when used in the neck

area - uncanny! This is subtle however. I hasten to add that power is not the be all and end all,

indeed, it is quite possible to design very effective low power pulsers with exceptionally fast

pulse rise times that can surpass the performance of even the most powerful pulser. Unlike the

high power pulsers these minimize dangers from electromagnetic radiation. So be warned and

don't get carried away with the lure of high power! It has been long known amongst alternate

energy and electromedicine researchers that very high speed pulses have the ability to tap into

some form of radiant energy that is generally not recognized by mainstream science. Devices

with very weak but high speed pulses in nanosecond range have been build and efficaciously

used by NASA engineers. This is a well known phenomena and I have worked it out

mathematically to my satisfaction. More on this at a later date. One theory is that such weak

high speed pulses are able to by pass the cell electromagnetic defences by their sheer speed

but certainly there are other issues a play such as tapping radiant energy... For a better

description on this please see Dr. Glen Gordon's video here. (http://video.google.com

/videoplay?docid=-5695988460216444662) Dr. Gordon was a candidate for a heart transplant but

managed to rebuild his own heart by just such a device.

See also: BIOELECTROMAGNETIC MEDICINE - THE BOOK (http://www.newmediaexplorer.org/chris/2004/09/16/bioelectromagnetic_medicine_the_book.htm)

Please note that this is not a permanent magnet but a pulsed magnet and as such the polarity

is not an issue, when the pulse collapses the magnetic field reverses. Hence one need not

worry about the magnetic polarity.

I still don't like the auto types as the body gets habituated to non random pulses the only

exceptions are possilbly the natural beat frequency of the Earth magnetic field (9.6 Hz) AND

the Schumann waves (7.83 Hz) - a random pulser circuit is still the goal but due to great

demand, much against my will, have now included a constant pulsing option for those who

requested it. For the sake of simplicity a neon lamp is used. Unfortunately neons are not very

stable and tend to vary as time goes by and may need to be replaced so use a socket for a

quick change. The pulsing rate can be changed and should be changed every so often

so the body does not get habituated, to that end I have added a switch to change the

pulse rates...

To calculate the output energy use the following:

Formula: W=(CE^2)/2

W=energy in joules: C = Capacitance in farads: E = Voltage across Capacitor in volts

Build a Low cost & simple Magnetic Pulser - Share The Wealth http://www.newmediaexplorer.org/chris/2003/08/19/build_a_low_cost_...

2 of 7 2/2/2011 1:36 PM

Page 3: Build a Low Cost & Simple Magnetic Pulser - Share the Wealth

# capacitors #Joules

5* 29

6 35

7 41

*Present circuit.

More on Capacitor Charge Calculations is here. (http://hyperphysics.phy-astr.gsu.edu/Hbase/electric/capchg.html#c2)

Any SCR with PEAK current of at least 600 to 1000 amps should work. The one shown is 20

amp continuous with the appropriate peak rating. The lamps act as current limiters and protect

the SCR against a short circuit. The circuit can be further simplified as discussed in point 3

below.

I have build several of these and my experience has been:

1) The capacitors develop a memory and don't fully discharge its better to use a number of

them in parallel. This reduces the internal resistance and provides a better result and less

memory loss. The caps must be designed for flash applications. They need not all be the same

value but must be the minimum voltage rating stated.

2) In the original Beck based designs the flash tube heats and develops some resistance so you

need to have enough time between flashes for them to cool down. This has been eliminated in

my circuit, however, you still need some time for the capacitors to charge up. The larger the

capacitor bank the longer it will take to charge up. Those planning to incorporate the automatic

version must be mindful of this and adjust the timer circuit to compensate this effect.

3) Using a high current SCR (forces the caps to fully discharge by providing a longer connection

than the strobe) and parallel caps from disposable cameras I can now consistently get 12 - 18

inch jumps with #14 fender washers. You can cycle them very fast (though not recommended).

All for less than $30 to $50 Cdn. The most expensive part is the coil which can cost as much a

$20 unless you build it yourself! One can further reduce the cost if at a latter date you don't

want to upgrade to auto pulsing. This can be accomplished by removing the 10k resistor and

the SCR and by simply wiring the a push to close switch in line to the coil. Don't recommend

this unless you just can't get an SCR or really need to reduce cost. MAKE SURE THE PUSH

BUTTON SWITCH CAN HANDLE THE CURRENT AND IS MECHANICALLY ROBUST!

More info regarding other coils options etc. is available at:

http://www.keelynet.com/biology/thumind.htm (http://www.keelynet.com/biology/thumind.htm)

Coil winding instructions from Dr. Beck's paper are:

"Junk VHS videocassette reels are cheap, plentiful and adequate for this application. Remove 5

screws from shell, remove reels and discard tape. Be SURE alternative spools (if used) are

non-conductive or system will not work. Avoid shorter length VHS tape reels which may have

center hubs larger than 1" dia. and won't hold sufficient wire. Drill 1/4" holes through hub and

through center of flange(s). Make two 4" discs from 1/4" thick plastic or fiberboard, drill 1/4"

center holes and another 1/4" hole off-center so coil's inside lead wire can be pulled through.

These 'stiffeners' will sandwich reel's flanges so they won't warp or split as wire pressure builds

up while winding progresses. A 2" (or longer) 1/4-20 machine nut and bolt with washers

through centers will clamp flange stiffeners and reel and also provide a shaft to hold in a

variable speed drill motor or similar winding device if used. Then remove bolt and stiffeners.

Specifications: Completely fill tape spool with #14 or 16 enameled copper magnet wire (130 to

160 turns) wound onto the 1" dia. hub and 3-1/2" OD spool with a gap width for wire of 5/8".

Scrape enamel insulation 1/2" from ends and tin. Pull inside end of magnet wire through hub

and stiffener and to outside. ~130 turns (about About 1-1/2 lbs should fill spool. Remove bolt,

stiffeners, and finished coil. Now solder ends of 3 ft of heavy two-wire extension cord to each

side of coil. Finished coil weighs ~1 LB 3 oz, has ~0.935 millihenry inductance, 0.34 ohm

resistance, and takes ~20 minutes to hand wind or ~3 minutes with drill motor. An excellent

alternative is an AMS brand air-core crossover inductor for home audio, #16 gauge, 2.5mH,

2-1/2" dia., $17.90 (http://www.madisound.com/catalog/product_info.php?products_id=988) from

Build a Low cost & simple Magnetic Pulser - Share The Wealth http://www.newmediaexplorer.org/chris/2003/08/19/build_a_low_cost_...

3 of 7 2/2/2011 1:36 PM

Page 4: Build a Low Cost & Simple Magnetic Pulser - Share the Wealth

Madisound speaker components.

Those interested in using a 12 V DC source use a cheap 75 watt car inverter

(http://www.amazon.com/Watt-Power-Inverter-110V-Automobile/dp/B001MK75KA) I bought one on

sale for just $7 Cdn! Simply remove one of the bulbs. This of course is easier if at least one

bulb is in a socket.

I have also attached a file for the free CircuitMaker Student Version (http://my.ece.ucsb.edu

/bobsclass/2C/Simulation/circuit_maker.htm) electronics software for those interested in modifying

the simple circuit that I have developed.

Build a Low cost & simple Magnetic Pulser - Share The Wealth http://www.newmediaexplorer.org/chris/2003/08/19/build_a_low_cost_...

4 of 7 2/2/2011 1:36 PM

Page 5: Build a Low Cost & Simple Magnetic Pulser - Share the Wealth

pulserworking20090209.ckt (http://www.newmediaexplorer.org/chris/pulserworking20090209.ckt)

Please share your experience so all can benefit. Thanks

Chris Gupta

Sites of interest:

- Here are a few articles on Pulsed Electro-Magnetic Field (PEMF) Therapy.(http://www.dansenhancerpages.com/moreinfoenhancerarticles.html)

- Steffan Heydon' Home-Made Bob Beck Electromagnetic Pulser based on this basic design.(http://www.twotowers.com/beck/beck_emp.html)

- Bil Green's M-Pulse 5000 with lots of supporting info. (http://magpulser.com/)

(http://www.newmediaexplorer.org/chris/MVC-015F.JPG)

Build a Low cost & simple Magnetic Pulser - Share The Wealth http://www.newmediaexplorer.org/chris/2003/08/19/build_a_low_cost_...

5 of 7 2/2/2011 1:36 PM

Page 6: Build a Low Cost & Simple Magnetic Pulser - Share the Wealth

(http://www.newmediaexplorer.org/chris/MVC-014F.JPG)

(http://www.newmediaexplorer.org/chris/MVC-016F.JPG)

Build a Low cost & simple Magnetic Pulser - Share The Wealth http://www.newmediaexplorer.org/chris/2003/08/19/build_a_low_cost_...

6 of 7 2/2/2011 1:36 PM

Page 7: Build a Low Cost & Simple Magnetic Pulser - Share the Wealth

posted by Chris Gupta on Tuesday August 19 2003

updated on Thursday February 19 2009

URL of this article:

http://www.newmediaexplorer.org/chris/2003/08

/19/build_a_low_cost_simple_magnetic_pulser.htm

Related Articles

Mobile Phones Increase Tumor Risk, Study Says (http://www.newmediaexplorer.org/chris/2004/11/03/mobile_phones_increase_tumor_risk_study_says.htm)

Further to the post: Em Fields On Brain Tumor Incidence - Chemicals And Cell Phones Chris

Gupta ---------------------- Mobile Phones Increase Tumor Risk, Study Says Thu Oct 14, 1:38

AM ET STOCKHOLM (Reuters) - Ten or more years of mobile phone use increases the risk of

developing acoustic neuroma, a benign tumor on the auditory nerve, according to a study

released on Wednesday by Sweden's Karolinska Institute. The risk was... [read more(http://www.newmediaexplorer.org/chris/2004/11

/03/mobile_phones_increase_tumor_risk_study_says.htm) ]

November 03, 2004 - Chris Gupta

Em Fields On Brain Tumor Incidence - Chemicals And Cell Phones(http://www.newmediaexplorer.org/chris/2004/10/20/em_fields_on_brain_tumor_incidence_chemicals_and_cell_phones.htm)

..."In a series of studies, Hardell and colleagues have examined the relationship between the

side of the head habitually used in operation of cellular and cordless phones and a possible

relationship to the site of brain tumors ([Hardell et al., 2003]). The risk for ipsilateral (same

side) use significantly increased the risk for astrocytoma for all types of phones, but use of the

phone on the opposite side of the... [read more (http://www.newmediaexplorer.org/chris/2004/10

/20/em_fields_on_brain_tumor_incidence_chemicals_and_cell_phones.htm) ]

October 20, 2004 - Chris Gupta

BIOELECTROMAGNETIC MEDICINE - THE BOOK (http://www.newmediaexplorer.org/chris/2004/09/16/bioelectromagnetic_medicine_the_book.htm)

...""In the decade to come, it is safe to predict, bioelectromagnetics will assume a therapeutic

importance equal to, or greater than, that of pharmacology and surgery today. With proper

interdisciplinary effort, significant inroads can be made in controlling the ravages of cancer,

some forms of heart disease, arthritis, hormonal disorders, and neurological scourges such as

Alzheimer's disease, spinal cord injury, and multiple sclerosis. This prediction is not pie-in-

the-sky. Pilot studies... [read more (http://www.newmediaexplorer.org/chris/2004/09

/16/bioelectromagnetic_medicine_the_book.htm) ]

September 16, 2004 - Chris Gupta

344

Build a Low cost & simple Magnetic Pulser - Share The Wealth http://www.newmediaexplorer.org/chris/2003/08/19/build_a_low_cost_...

7 of 7 2/2/2011 1:36 PM