EN 300 440 Test Report - ООО "Гамма" · 2013-04-01 · EN 300 440 Test Report Product Name : Wireless Module Model No. : SIM5320E Applicant : Shanghai Simcom Ltd. Address

EN 300 440 Test Report

Product Name : Wireless Module

Model No. : SIM5320E

Applicant : Shanghai Simcom Ltd.

Address : Building A, SIM Technology Building, No. 633, Jinzhong

Road, Changning Disdrict, Shanghai P.R. China 200335

Date of Receipt : 08/06/2011

Test Date : 08/06/2011~16/06/2011

Issued Date : 16/06/2011

Report No. : 112S010R-RF-CE-P14V02

Report Version : V1.0

The test results relate only to the samples tested.The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF, NVLAP or any agency of the Government. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation.

Report No： 112S010R-RF-CE-P14V02

Page: 2 of 30

Test Report Cert i f icat ion Issued Date : 16/06/2011 Report No. : 112S010R-RF-CE-P14V02

Product Name : Wireless Module

Applicant : Shanghai Simcom Ltd.



Manufacturer : Shanghai Simcom Ltd.



Model No. : SIM5320E

EUT Voltage : 3.7V/3.4V/4.2V

Brand Name : SIMCom

Applicable Standard : ETSI EN 300 440-1 V1.6.1 (2010-08)

ETSI EN 300 440-2 V1.4.1 (2010-08)

Test Result : Complied

Performed Location : Suzhou EMC Laboratory

No.99 Hongye Rd., Suzhou Industrial Park Loufeng

Hi-Tech Development Zone., Suzhou, China

TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098

Documented By :

(Engineering ADM: Alice Ni)

Reviewed By :

(Senior Engineer: Robin Wu)

Approved By :

(Engineering Supervisor: Marlin Chen)


Page: 3 of 30

Laboratory Information

We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted(audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scope:

The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site : http://www.quietek.com/tw/ctg/cts/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don’t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : [email protected]

LinKou Testing Laboratory : No. 5-22, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : [email protected]

Suzhou (China) Testing Laboratory : No. 99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou,China. TEL : +86-512-6251-5088 / FAX : +86-512-6251-5098 E-Mail : [email protected]

Taiwan R.O.C. : BSMI, NCC, TAF

Germany : TUV Rheinland

Norway : Nemko, DNV

USA : FCC, NVLAP

Japan : VCCI


Page: 4 of 30

TABLE OF CONTENTS Description Page 1. General Information........................................................................................................6 1.1. EUT Description ..............................................................................................6 1.2. Mode of Operation...........................................................................................7 1.3. Tested System Details .....................................................................................8 1.4. Configuration of Tested System.......................................................................9 1.5. EUT Exercise Software....................................................................................9 2. Technical Test ............................................................................................................... 11 2.1. Summary of Test Result................................................................................. 11 2.2. Measurement Uncertainty..............................................................................12 2.3. Test Environment...........................................................................................13 3. Equivalent Isotropic Radiated Power (EIRP) ................................................................14 3.1. Test Equipment..............................................................................................14 3.2. Test Setup .....................................................................................................15 3.3. Limit...............................................................................................................16 3.4. Test Procedure ..............................................................................................16 3.5. Test Result.....................................................................................................16 4. Permitted Range of Operating Frequencies .................................................................17 4.1. Test Equipment..............................................................................................17 4.2. Test Setup .....................................................................................................17 4.3. Limit...............................................................................................................17 4.4. Test Procedure ..............................................................................................18 4.5. Test Result.....................................................................................................18 5. Transmitter Spurious Emissions ...................................................................................19 5.1. Test Equipment..............................................................................................19 5.2. Test Setup .....................................................................................................20 5.3. Limit...............................................................................................................21 5.4. Test Procedure ..............................................................................................21 5.5. Test Result.....................................................................................................21 6. Receiver Spurious Emissions .......................................................................................22 6.1. Test Equipment..............................................................................................22 6.2. Test Setup .....................................................................................................23 6.3. Limit...............................................................................................................24 6.4. Test Procedure ..............................................................................................24 6.5. Test Result.....................................................................................................25 6.6. Test Photograph ............................................................................................25 7. Duty Cycle ....................................................................................................................27 7.1. Test Equipment..............................................................................................27


Page: 5 of 30

7.2. Test Setup .....................................................................................................27 7.3. Limit...............................................................................................................28 7.4. Test Procedure ..............................................................................................28 7.5. Test Result.....................................................................................................28 8. Attachment ...................................................................................................................29 　 EUT Photograph............................................................................................29


Page: 6 of 30

1. General Information 1.1. EUT Description

Product Name Wireless Module

Brand Name SIMCom

Model No. SIM5320E

Working Voltage 3.7V/3.4V/4.2V

GPS Function YES

Tx Frequency Range GSM900: 880MHz to 915MHz DCS1800: 1710MHz to 1785MHz WCDMA: 1920MHz to 1980MHz (Band I)

Rx Frequency Range GSM900: 925MHz to 960MHz DCS1800: 1805MHz to 1880MHz WCDMA: 2110MHz to 2170MHz (Band I)

Channel Number GSM900: 173 DCS1800: 373 WCDMA: 277

Type of Modulation GMSK for GSM&GPRS 8PSK for EDGE QPSK for WCDMA

Channel Control Auto


Page: 7 of 30

1.2. Mode of Operation QuieTek has verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: Test Mode

Mode 1: GPS Receive


Page: 8 of 30

1.3. Tested System Details The types for all equipments, plus descriptions of all cables used in the tested system (including inserted cards) are:

Product Manufacturer Model No. Serial No. Power Cord

1 SG Agilent E4438C N/A N/A


Page: 9 of 30

1.4. Configuration of Tested System

Connection Diagram

Signal Cable Type Signal cable Description

A Coaxial Cable Shielded, >5m

EUT A

1


Page: 10 of 30

1.5. EUT Exercise Software

1 Setup the EUT and simulators as shown on above.

2 Turn on the power of equipment.

3 Make the EUT work under the “GPS” Mode.

4 Turn to Test.


Page: 11 of 30

2. Technical Test 2.1. Summary of Test Result

No deviations from the test standards Deviations from the test standards as below description:

Performed Test Item Normative References Test

Performed Deviation

Equivalent Isotropic Radiated

Power (EIRP)

ETSI EN 300 440-1 V1.6.1 (2010-08) N/A N/A

Permitted Range of Operating

Frequencies

ETSI EN 300 440-1 V1.6.1 (2010-08) N/A N/A

Transmitter Spurious Emissions ETSI EN 300 440-1 V1.6.1 (2010-08) N/A N/A

Receiver Spurious Emissions ETSI EN 300 440-1 V1.6.1 (2010-08) Yes No

Duty Cycle ETSI EN 300 440-1 V1.6.1 (2010-08) N/A N/A


Page: 12 of 30

2.2. Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the apparatus:

Parameter Uncertainty

RF Frequency ±1 x 10-7

RF Power (Conducted) ±0.7dB

Radiated Emission of Transmitter, Valid to 80 GHz

±5.2dB

Radiated Emission of Receiver, Valid to 80 GHz

±5.2dB

Temperature ±0.5℃

Humidity ±1%


Page: 13 of 30

2.3. Test Environment

Items Required (IEC 68-1) Actual

Temperature (°C) 15-35 21

Humidity (%RH) 25-75 50

Barometric pressure (mbar) 860-1060 950-1000


Page: 14 of 30

3. Equivalent Isotropic Radiated Power (EIRP)

3.1. Test Equipment Equivalent Isotropic Radiated Power (EIRP) / TR-8

Instrument Manufacturer Type No. Serial No. Cal. Due Date

Power Meter Anritsu ML2495A 0905006 2012/01/12

Power Sensor Anritsu MA2411B 0846014 2012/01/12

DC Power Supply IDRC CD-035-020PR 977272 2011/10/21

Programmable

Temperature &

Humidity Chamber

Gaoyu TH-1P-B WIT-05121302 2012/01/19

Temperature/Humidity

Meter Zhicheng ZC1-2 TR8-TH 2012/05/04

Note: All equipments are calibrated with traceable calibrations. Each calibration is traceable to the national

or international standards.


Page: 15 of 30

3.2. Test Setup For Conducted Measurement

Power Meter

12dBm

Temperature Chamber

Power Supply


Page: 16 of 30

3.3. Limit

Maximum radiated peak power (e.i.r.p.) Frequency Bands Power Application Notes

2400MHz to 2483.5MHz 10 mW e.i.r.p. Generic use

2400MHz to 2483.5MHz 25 mW e.i.r.p. Detection, movement and alert

applications

(a) 2466MHz to 2454MHz 500 mW e.i.r.p. RFID See also table 7 and annex C

(b) 2466MHz to 2454MHz 4 W e.i.r.p. RFID See also table 7 and annex C

5725MHz to 5875MHz 25 mW e.i.r.p. Generic use

9200MHz to 9500MHz 25 mW e.i.r.p. Detection, movement and alert

applications

9500MHz to 9975MHz 25 mW e.i.r.p. Detection, movement and alert

applications

10.5GHz to 10.6GHz 25 mW e.i.r.p. Detection, movement and alert

applications

13.4GHz to 14.0GHz 25 mW e.i.r.p. Detection, movement and alert

applications

17.1GHz to 17.3GHz 400 mW e.i.r.p. GBSAR detection, movement and

alert applications

See annex E

24.00GHz to 24.25GHz 100 mW e.i.r.p Generic use and detection,

movement and alert application

3.4. Test Procedure

Refer to ETSI EN 300 440-1 V1.6.1 (2010-08) Clause 7.1

3.5. Test Result

It is not suitable to perform this test item.


Page: 17 of 30

4. Permitted Range of Operating Frequencies

4.1. Test Equipment Permitted Range of Operating Frequencies / TR-8


Spectrum Analyzer Agilent E4446A MY45300103 2012/04/30

DC Power Supply IDRC CD-035-020PR 977272 2011/10/21

Programmable

Temperature &

Humidity Chamber

Gaoyu TH-1P-B WIT-05121302 2012/01/19





4.2. Test Setup

4.3. Limit The width of the power envelope is fH - fL for a given operating frequency. In equipment that allows adjustment or selection of different operating frequencies, the power envelope takes up different positions in the allowed band. The frequency range is determined by lowest value of fL

and the highest value of fH resulting from the adjustment of the equipmentto the lowest and highest operating frequencies.

Spectrum

12dBm

Temperature Chamber

Power Supply


Page: 18 of 30

4.4. Test Procedure Refer to ETSI EN 300 440-1 V1.6.1 (2010-08) Clause 7.2

4.5. Test Result It is not suitable to perform this test item.


Page: 19 of 30

5. Transmitter Spurious Emissions

5.1. Test Equipment Transmitter Spurious Emissions / AC-6



PSG Analog S.G. Agilent E8257D MY44321116 2012/04/23

Preamplifier QuieTek AP-025C CHM-0503006 2012/05/05


Bilog Type Antenna Schaffner CBL6112D 22254 2011/10/18

Half Wave Tuned

Dipole Antenna COM-POWER AD-100 40137 2011/11/24

Broad-Band Horn

Antenna Schwarzbeck BBHA9120D 499 2012/06/11

Broad-Band Horn


High-Pass Filter Wainwright WHKX2.8/18G-12SS SN1 2012/03/03

Band Reject Filter Wainwright WRCG2400/2485-2375

/2510-60/11SS SN9 2012/03/03


Meter zhicheng ZC1-2 AC6-TH 2012/01/14




Page: 20 of 30

5.2. Test Setup For Radiated Measurement


Page: 21 of 30

5.3. Limit

Radiated Spurious Emissions for Transmitter State 47 MHz to 74 MHz

87.5 MHz to 118 MHz174 MHz to 230 MHz470 MHz to 862 MHz

Other frequencies ≦1000 MHz

Frequencies >1000 MHz

Operating 4 nW 250 nW 1 uW

Standby 2 nW 2 nW 20 nW

5.4. Test Procedure


5.5. Test Result



Page: 22 of 30

6. Receiver Spurious Emissions

6.1. Test Equipment Receiver Spurious Emissions / AC-6



PSG Analog S.G. Agilent E8257D MY44321116 2012/04/23



Bilog Type Antenna Schaffner CBL6112D 22254 2011/10/18

Half Wave Tuned

Dipole Antenna COM-POWER AD-100 40137 2011/11/24

Broad-Band Horn


Broad-Band Horn


High-Pass Filter Wainwright WHKX2.8/18G-12SS SN1 2012/03/03

Band Reject Filter Wainwright WRCG2400/2485-2375

/2510-60/11SS SN9 2012/03/03


Meter zhicheng ZC1-2 AC6-TH 2012/01/14




Page: 23 of 30

6.2. Test Setup For Radiated Measurement


Page: 24 of 30

6.3. Limit The power of any spurious emission shall not exceed 2 nW in the range 25 MHz to 1 GHz and shall not exceed 20 nW on frequencies above 1 GHz.

6.4. Test Procedure Refer to ETSI EN 300 440-1 V1.6.1 (2010-08) Clause 8.4


Page: 25 of 30

6.5. Test Result

Product : Wireless Module

Test Item : Spurious Emission

Test Site : AC-6

Test Mode : Mode 1: GPS Receive

Frequency (MHz)

Polarization (H/V)

Measure Level(dBm)

Limit (dBm)

Margin (dB)

Detector

99.84 H -69.34 -57.0 -12.34 Peak

75.11 V -74.24 -57.0 -17.24 Peak

252.62 H -68.12 -57.0 -11.12 Peak

131.85 V -78.09 -57.0 -21.09 Peak

367.56 H -64.68 -57.0 -7.68 Peak

288.02 V -69.52 -57.0 -12.52 Peak

1238.00 H -56.66 -47.0 -9.66 Peak

1374.00 V -56.99 -47.0 -9.99 Peak

2258.00 H -54.34 -47.0 -7.34 Peak

2156.00 V -55.55 -47.0 -8.55 Peak

3703.00 H -52.56 -47.0 -5.56 Peak

2972.00 V -54.20 -47.0 -7.20 Peak


Page: 26 of 30

6.6. Test Photograph Description: Receiver Spurious Emissions Test Setup for Below 1GHz

Description: Receiver Spurious Emissions Test Setup for Above 1GHz


Page: 27 of 30

7. Duty Cycle

7.1. Test Equipment Duty Cycle / TR-8







7.2. Test Setup


Page: 28 of 30

7.3. Limit

Duty Cycle Limits Frequency Band Duty Cycle Application Notes

2 400 MHz to 2 483,5 MHz No Restriction Generic use 2 400 MHz to 2 483,5 MHz No Restriction Detection, movement and alert

applications

(a) 2 446 MHz to 2 454 MHz No Restriction RFID See annex C

(b) 2 446 MHz to 2 454 MHz ≤ 15 % RFID See annex C

5 725 MHz to 5 875 MHz No Restriction Generic use 9 200 MHz to 9 500 MHz No Restriction Detection, movement and alert

applications

9 500 MHz to 9 975 MHz No Restriction Detection, movement and alert

applications

10,5 GHz to 10,6 GHz No Restriction Detection, movement and alert

applications

13,4 GHz to 14,0 GHz No Restriction Detection, movement and alert

applications

17,1 GHz to 17,3 GHz DAA or equivalent

techniques

GBSAR detecting and movement and

alert applications

See annex E

24,00 GHz to 24,25 GHz No Restriction Generic use and for detection,

movement and alert applications

7.4. Test Procedure


7.5. Test Result



Page: 29 of 30

8. Attachment EUT Photograph

(1) EUT Photo

(2) EUT Photo


Page: 30 of 30

(3) EUT Photo

(4) EUT Photo

Documents

EN 300 440 Test Report - ООО "Гамма" · 2013-04-01 · EN 300 440 Test Report Product Name : Wireless Module Model No. : SIM5320E Applicant : Shanghai Simcom Ltd. Address