GRUNDFOS DATA BOOKLET

TPE 100-90/4-A-F-A-BQQE 3X400 50HZ Grundfos Pump 99113703

Thank you for your interest in our productsPlease contact us for more information, or visit our websitehttps://www.lenntech.com/grundfos/TPE00/99113703/TPE-100-90-4-A-F-A-BQQE.html

info@lenntech.comtel. +31-15-261.09.00fax. +31-15-261.62.89

BE > THINK > INNOVATE

Printed from Grundfos Product Centre [2018.02.043]

Position Qty. Description1 TPE 100-90/4 A-F-A-BQQE

Product No.: 99113703

Single-stage, close-coupled, volute pump with in-line suction and discharge ports of identical diameter.The pump is of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can beremoved for maintenance or service while the pump housing remains in the pipework.The pump is fitted with an unbalanced rubber bellows seal. The shaft seal is according to EN 12756.Pipework connection is via PN 16 DIN flanges (EN 1092-2 and ISO 7005-2).The pump is fitted with a fan-cooled, permanent-magnet synchronous motor. The motor includes afrequency converter and PI controller in the motor terminal box. This enables continuously variablecontrol of the motor speed, which again enables adaptation of the performance to a given requirement.

Further product detailsA control panel enables setting of required setpoint as well as setting of pump to "Min." or "Max."operation or to "Stop". The control panel has indicator lights for "Operation" and "Fault".

Communication with the pump is possible by means of the Grundfos GO Remote (accessory). Theremote control enables further settings as well as reading out of a number of parameters such as"Actual value", "Speed", "Power input" and total "Power consumption".

A control panel on the motor terminal box enables setting of required setpoint as well as setting ofpump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the control panelprovides visual indication of pump status:

- "Power on": Motor is running (rotating green indicator lights) or not running (permanently greenindicator lights)

- "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanentlyyellow indicator lights)

- "Alarm": Motor has stopped (flashing red indicator lights).

Communication with the pump is possible by means of the Grundfos GO Remote (accessory). Theremote control enables further settings as well as reading out of a number of parameters such as"Actual value", "Speed", "Power input" and total "Power consumption".

The product's minimum efficiency index (MEI) is greater or equal to 0.70. This is by the CommissionRegulation (EU) considered as an indicative benchmark for best-performing water pump available onthe market as from 1 January 2013.

PumpPump housing and pump head are electrocoated to improve the corrosion resistance.Electrocoating includes:1) Alkaline-based cleaning.2) Pretreatment with zinc phosphate coating.3) Cathodic electrocoating (epoxy).4) Curing of paint film at 200-250 °C.

Printed from Grundfos Product Centre [2018.02.043]

1: Pump housing2: Impeller3: Stub shaft4: Pump head/motor stool5: Wear rings

The pump housing is provided with a replaceable bronze neck ring to reduce the amount of liquidrunning from the discharge side of the impeller to the suction side. The impeller is secured to the shaftwith a nut.

The pump is fitted with an unbalanced rubber bellows seal with torque transmission across the springand around the bellows. Due to the bellows, the seal does not wear the shaft, and the axial movementis not prevented by deposits on the shaft.Primary seal:

- Rotating seal ring material: Silicon carbide (SiC)- Stationary seat material: Silicon carbide (SiC)

This material pairing is used where higher corrosion resistance is required. The high hardness of thismaterial pairing offers good resistance against abrasive particles.Secondary seal material: EPDM (ethylene-propylene rubber)EPDM has excellent resistance to hot water. EPDM is not suitable for mineral oils.

A circulation of liquid through the duct of the air vent screw ensures lubrication and cooling of the shaftseal.The flanges have tappings for mounting of pressure gauges.

The motor stool forms connection between the pump housing and the motor, and is equipped with amanual air vent screw for venting of the pump housing and the shaft seal chamber. The sealingbetween motor stool and pump housing is an O-ring.The central part of the motor stool is provided with guards for protection against the shaft and coupling.The pump stub shaft is fastened directly on the motor shaft with key and set screws.

MotorThe motor is a totally enclosed, fan-cooled motor with principal dimensions to IEC and DIN standards.Electrical tolerances comply with IEC 60034.

The motor is flange-mounted with free-hole flange (FF).Motor mounting designation in accordance with IEC 60034-7: IM B 5, IM V 1 (Code I) / IM 3001, IM3011 (Code II).

The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2.The motor requires no external motor protection. The motor control unit incorporates protection againstslow- and quick-rising temperatures, e.g. constant overload and stalled conditions.

The terminal box holds terminals for these connections:- one dedicated digital input- two analog inputs, 0(4)-20 mA, 0-5 V, 0-10 V, 0.5 - 3.5 V- 5 V voltage supply to potentiometer and sensor- one configurable digital input or open-collector output- Grundfos Digital Sensor input and output- 24 V voltage supply for sensors- two signal relay outputs (potential-free contacts)- GENIbus connection- interface for Grundfos CIM fieldbus module.

Printed from Grundfos Product Centre [2018.02.043]

Position Qty. Description

Technical data

Liquid:Pumped liquid: WaterLiquid temperature range: -25 .. 120 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³

Technical:Speed for pump data: 1445 rpmRated flow: 69.5 m³/hRated head: 8.08 mActual impeller diameter: 168 mmPrimary shaft seal: BQQECurve tolerance: ISO9906:2012 3B

Materials:Pump housing: Cast iron

EN-JL1040ASTM A48-40 B

Impeller: Cast ironEN-JL1030ASTM A48-30 B

Installation:Range of ambient temperature: -20 .. 50 °CMaximum operating pressure: 16 barFlange standard: DINPipe connection: DN 100Pressure rating: PN 16Port-to-port length: 550 mmFlange size for motor: FF215

Electrical data:Motor type: 100LBIE Efficiency class: IE5Rated power - P2: 2.2 kWMains frequency: 50 HzRated voltage: 3 x 380-500 VRated current: 4,30-3,60 ACos phi - power factor: 0,90-0,82Rated speed: 180-2200 rpmEfficiency: 89,1%Enclosure class (IEC 34-5): IP55Insulation class (IEC 85): F

Others:Minimum efficiency index, MEI ≥: 0.70ErP status: EuP Standalone/Prod.Net weight: 101 kgGross weight: 120 kgShipping volume: 0.39 m³Danish VVS No.: 382056090Norwegian NRF no.: NRF NO 9043655

Printed from Grundfos Product Centre [2018.02.043]

99113703 TPE 100-90/4 50 HzH

[m]

0

1

2

3

4

5

6

7

8

9

10

11

Q [m³/h]0 10 20 30 40 50 60 70 80 90 100 110

eta[%]

0

20

40

60

80

100

TPE 100-90/4, 3*500 V

110 %

100 %

90 %

80 %

70 %

60 %

50 %

40 %

25 %20 %

P[kW]

0.0

0.5

1.0

1.5

2.0

2.5

NPSH[m]

0

2

4

6

8

10P1 (motor+freq.converter)

P2

Printed from Grundfos Product Centre [2018.02.043]

H[m]

0

1

2

3

4

5

6

7

8

9

10

11

Q [m³/h]0 20 40 60 80 100

eta[%]

0

20

40

60

80

100

TPE 100-90/4, 3*500 V

110 %

100 %

90 %

80 %

70 %

60 %

50 %

40 %

25 %20 %

P[kW]

0.0

0.5

1.0

1.5

2.0

2.5

NPSH[m]

0

2

4

6

8

10P1 (motor+freq.converter)

P2

275

100

191.3

M16

Rp 1/4

201 201

201

145.5145.5

201

140

0

675

151190 550

230

3

15

8

26

23

25

24

7

21

20

22

B

Y

6

5

2

4

10

A

+24 V*

1

149

12

17

19

11

18+24 V*

OC DI

+24 V*

AI2

GDS RX

GDS TX

GND

GENIbus A

GENIbus B

+24 V

GND

GENIbus Y

GND

DI1

AI1

DI3/OC1

LiqTec

AI3

GND

DI2

LiqTec

GND

AO

Pt100/1000

Pt100/1000

DI4/OC2

GND

+24 V*OC DIGND

NC

C2

NO

NC

C1

NO

+24 V*+24 V* +24 V*/5 V*

L2

L1

L3

PE

L3

L2

L1

+24 V* +24 V*/5 V*+24 V*

+24 V*/5 V*

+5 V*

+5 V

+24 V

+5 V

+5 V*

Description ValueGeneral information:Product name: TPE 100-90/4 A-F-A-BQQEProduct No: 99113703EAN number: 5712607014650Technical:Speed for pump data: 1445 rpmRated flow: 69.5 m³/hRated head: 8.08 mHead max: 90 dmActual impeller diameter: 168 mmPrimary shaft seal: BQQECurve tolerance: ISO9906:2012 3BPump version: AModel: AMaterials:Pump housing: Cast iron

EN-JL1040ASTM A48-40 B

Impeller: Cast ironEN-JL1030ASTM A48-30 B

Material code: AInstallation:Range of ambient temperature: -20 .. 50 °CMaximum operating pressure: 16 barFlange standard: DINConnect code: FPipe connection: DN 100Pressure rating: PN 16Port-to-port length: 550 mmFlange size for motor: FF215Liquid:Pumped liquid: WaterLiquid temperature range: -25 .. 120 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³Electrical data:Motor type: 100LBIE Efficiency class: IE5Rated power - P2: 2.2 kWMains frequency: 50 HzRated voltage: 3 x 380-500 VRated current: 4,30-3,60 ACos phi - power factor: 0,90-0,82Rated speed: 180-2200 rpmEfficiency: 89,1%Enclosure class (IEC 34-5): IP55Insulation class (IEC 85): FMotor protec: YESMotor No: 98971181Controls:Control panel: HMI200 - StandardFunction Module: FM300 - AdvancedOthers:Minimum efficiency index, MEI ≥: 0.70ErP status: EuP Standalone/Prod.Net weight: 101 kgGross weight: 120 kgShipping volume: 0.39 m³Config. file no: 99100729Danish VVS No.: 382056090Norwegian NRF no.: NRF NO 9043655

275

100

191.3

M16

Rp 1/4

201201201

145.5145.5

151190550

Printed from Grundfos Product Centre [2018.02.043]

99113703 TPE 100-90/4 50 Hzcos phi

eta

0.0

0.2

0.4

0.6

0.8

P2 [kW]0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1

I[A]

0.0

1.0

2.0

3.0

4.0

TPE100-90/4 + 100LB 2.2 kW 3*500 V, 50 Hz

eta

cos phi

I

n[rpm]

0

400

800

1200

1600

P1[kW]

0.0

1.0

2.0

3.0

n

P1 (motor+freq.converter)

n = 109 %

Printed from Grundfos Product Centre [2018.02.043]

99113703 TPE 100-90/4 50 Hz

Note! All units are in [mm] unless others are stated.Disclaimer: This simplified dimensional drawing does not show all details.

275

100

191.3

M16

Rp 1/4

201 201

201

145.5145.5

201

140

0

675

151190 550

230

Printed from Grundfos Product Centre [2018.02.043]

99113703 TPE 100-90/4 50 Hz

Note! All units are in [mm] unless others are stated.

3

15

8

26

23

25

24

7

21

20

22

B

Y

6

5

2

4

10

A

+24 V*

1

14

9

12

17

19

11

18+24 V*

OC DI

+24 V*

AI2

GDS RX

GDS TX

GND

GENIbus A

GENIbus B

+24 V

GND

GENIbus Y

GND

DI1

AI1

DI3/OC1

LiqTec

AI3

GND

DI2

LiqTec

GND

AO

Pt100/1000

Pt100/1000

DI4/OC2

GND

+24 V*OC DIGND

NC

C2

NO

NC

C1

NO

+24 V*+24 V* +24 V*/5 V*

L2

L1

L3

PE

L3

L2

L1

+24 V* +24 V*/5 V*+24 V*

+24 V*/5 V*

+5 V*

+5 V

+24 V

+5 V

+5 V*

Disclaimer: The information about the Grundfos pump in this document may be outdated.Data may be subject to alterations without further notice.Please contact us to verify the data above is still accurate/up-to-date.

All information is copyright Grundfos.

info@lenntech.comwww.lenntech.comtel. +31-15-261.09.00fax. +31-15-261.62.89