VCE.Testkings.210-010.v2015-03-19.by.Gayle - GRATIS · PDF fileYou are deploying a Vblock System and want to install recent patches to the ESXi host(s). Which VCE recommended method

Testkings.210-010.128.QA

Number: 210-010Passing Score: 800Time Limit: 120 minFile Version: 15.6

http://www.gratisexam.com/

I found the best preparation material which helped me in learning a lot. I got the score I always dreamt of. Thanks a lot.

To keep the students updated and well informed Examcollection team maintains quality of their work forcertification exams.

This study guide provides the guaranteed preparation material to boost up your confidence in exam.Guys, if you need to be certified, check out this study guide.

Best of Luck to everyone

Exam A

QUESTION 1Which EMC software is required to upgrade code on a Vblock System 200 storage array?

A. Unisphere Service ManagerB. Unisphere Server UtilityC. VNX Installation AssistantD. Unisphere Client

Correct Answer: ASection: (none)Explanation

Explanation/Reference:

QUESTION 2Which two statements are correct about Vblock System Release Certification Matrix (RCM) upgrades?(Choose two.)

A. The RCM must be applied by VCE certified resources.B. When upgrading to a new RCM, all components may not require an upgrade.C. The most recent RCM version must be applied.D. An addendum to the RCM may be issued to address a bug or software issue.

Correct Answer: BDSection: (none)Explanation


QUESTION 3Which Cisco Catalyst switch is used for network management on a Vblock System 200?

A. Cisco Catalyst 2960B. Cisco Catalyst 3560C. Cisco Catalyst 3750D. Cisco Catalyst 4500

Correct Answer: CSection: (none)Explanation


QUESTION 4The implementation profile located in the Logical Configuration Survey (LCS) identifies if the customer willbe using which two solutions? (Choose two.)

A. EMC SnapViewB. Cisco IACC. Cisco Unified CommunicationsD. VMware vCloud Director

Correct Answer: CDSection: (none)

Explanation


QUESTION 5What are three requirements of the Vblock System test plan? (Choose three.)


A. All tests identified in the test plan must be executed.B. Observed results must be documented by a VCE certified resource.C. Tests are confidential and must not be performed in view of the customer.D. Once tests are completed, the customer must sign the test plan document.E. A completed test plan must be submitted to the VCE project manager.

Correct Answer: BDESection: (none)Explanation


QUESTION 6Which test is only performed on a Vblock System 320 that contains a high availability AdvancedManagement Pod (HA-AMP)?

A. Cisco blade server failure testB. Cisco UCS single power supply failure testC. Cisco Catalyst 3560 failure and recovery testD. Cisco UCS C220 failover test

Correct Answer: DSection: (none)Explanation


QUESTION 7Your manager asks you to configure an external Syslog on VMware ESXi hosts.

In which two ways would the Syslog be configured? (Choose two.)

A. using the vSphere clientB. using the esxcli system syslog commandC. using VMware Update ManagerD. using the VMware SQL database

Correct Answer: ABSection: (none)Explanation


QUESTION 8When performing hardware maintenance on a Cisco UCS B-Series blade, which GUI parameter should beselected before removing the blade out of the chassis?

A. RemoveB. Re-acknowledgeC. DecommissionD. Diagnostic Interrupt



QUESTION 9A customer notices a failed drive error for a Vblock System 320 storage array on an EMC Unispherescreen.

Which logs must be collected and sent to VCE support to confirm that the drive has failed?

A. SPcollectsB. NAR filesC. symapi.logD. EMC Grab



QUESTION 10Which Cisco management software is required to setup EMC e-mail home for Cisco MDS switches?

A. Cisco Data Center Network Manager (Cisco DCNM-SAN)B. Cisco Unified Computing System Manager (Cisco UCSM)C. Cisco Smart Call Home (Cisco SCH)D. Cisco Terminal Access Controller Access Control System (Cisco TACACS)



QUESTION 11VCE support asks you to collect VMware diagnostic logs from an ESXi host.

Which two management tools would you use to accomplish this task? (Choose two.)

A. vSphere Client connected to ESXi hostB. VMware Update Manager (VUM) serverC. vSphere client connected to vCenter ServerD. VMware vCenter SQL database

Correct Answer: ACSection: (none)Explanation


QUESTION 12A VCE professional services engineer encounters a blade issue on a Cisco UCS B-230 during a Vblockimplementation. VCE Support requires the show tech-support log bundle to further isolate the problem.

For which two Cisco UCS components will VCE Support require the log bundle? (Choose two.)

A. UCSMB. bladeC. adapterD. chassis

Correct Answer: ADSection: (none)Explanation


QUESTION 13In Cisco Unified Computing System Manager (UCSM), which selection under the Admin tab would youselect to configure SNMP?

A. Call HomeB. Communication ServicesC. Management InterfacesD. Syslog

Correct Answer: BSection: (none)Explanation


QUESTION 14How many Cisco UCS C220 servers are used in a Vblock System mini Advanced Management Pod (mini-AMP)?

A. 1B. 2C. 3D. 4



QUESTION 15What is the data store location for Management Virtual Machines, in the high availability Advanced

Management Pod (HA-AMP)?

A. EMC VNXeB. EMC VNXC. Cisco UCS C220D. Cisco UCS B440



QUESTION 16What is the data store location for Management Virtual Machines, in the mini Advanced Management Pod(mini-AMP)?

A. EMC VNXeB. EMC VNXC. Cisco UCS C220D. Cisco UCS B440



QUESTION 17Which RAID type is used for the Cisco UCS C220 servers in a Vblock System 320 Advanced ManagementPod (AMP)?

A. RAID 0B. RAID 1C. RAID 5D. RAID 6



QUESTION 18How many EMC ESRS servers are deployed with a Vblock System 320 mini Advanced Management Pod(mini-AMP)?

A. 1B. 2C. 3D. 4



QUESTION 19What are two primary reasons for using the Advanced Management Pod (AMP)? (Choose two.)

A. disaster recoveryB. monitoringC. out-of-band-managementD. multi-tenancy

Correct Answer: BCSection: (none)Explanation


QUESTION 20A Vblock System is deployed by VCE using Unified Infrastructure Manager (UIM). During implementation, aproblem is encountered that requires the configuration to be changed in the underlying element managers.

Which utility will allow the UIM database to resynchronize with the underlying element manager's changedconfiguration?

A. Service Adoption UtilityB. VMware Migration ManagerC. Configuration CenterD. VCE Vision Compliance Checker



QUESTION 21VCE Vision Intelligent Operations has been installed on a customer's Vblock System. Which twoparameters would be selected within the configureSNMP command? (Choose two.)

A. delete trap targetB. sysContactC. add v1/v2c trap targetD. sysLocation



QUESTION 22You are required to log in to a Cisco UCS C220 CIMC to validate the firmware.

What are two ways to launch and obtain the login prompt? (Choose two.)

A. http://ipaddressB. http://ipaddress/cimc

C. https://hostnameD. https://ipaddress/cimc



QUESTION 23On which operating system is the EMC Ionix UIM/P virtual appliance based?

A. Red Hat LinuxB. SUSE LinuxC. CentOS LinuxD. Debian Linux



QUESTION 24Which two virtual machines are deployed as part of the Advanced Management Pod (AMP)? (Choose two.)

A. VMware View Connection serverB. VMware Update Manager serverC. Cisco Adaptive Security ApplianceD. VMware vCenter server



QUESTION 25Using VCE Vision Intelligent Operations, a system administrator accesses information about a VblockSystem with which two methods? (Choose two.)

A. UIM/P discovery viewB. vCenter Performance ChartsC. VCE Vision Plug-in for vCenterD. SNMP GETs from a MIB browser

Correct Answer: CDSection: (none)Explanation


QUESTION 26You must validate the management software for the Cisco MDS 9148 switch deployed with the AdvancedManagement Pod (AMP).

To which server would you log in?

A. ESRS serverB. array management serverC. vCenter serverD. VMware VUM server



QUESTION 27EMC Ionix UIM/P services are managed through service profiles comprised of server, network, and storageprofiles.

Before managing a service offering, which two actions must be completed? (Choose two.)

A. Discover the Vblock System.B. Install ESXi onto blades for discovery preparation.C. Mark graded storage pool as available.D. Configure the auto deploy server with IP pool.



QUESTION 28EMC Secure Remote Support (ESRS) is deployed in the Advanced Management Pod (AMP).


Which three hardware components are monitored by this call home software? (Choose three.)

A. EMC VNXeB. Cisco MDS 9148 switchC. Cisco Nexus 1000V switchD. EMC VMAXE. Cisco Catalyst 3650 switch

Correct Answer: ABDSection: (none)Explanation


QUESTION 29As a system administrator, which actions are performed using VCE Vision Intelligent Operations software?(Choose two.)

A. Monitor the health of (and events related to) Vblock System components.B. Validate that the Vblock System components comply with a release certification matrix.C. Perform initial configuration and initialization of Vblock System element managers.D. Deploy Advanced Management Pod (AMP) images from Virtual Center.



QUESTION 30Connectivity is required to manage the Vblock System 720 storage array in the Advanced Management Pod(AMP).

Which two types of switches would be used? (Choose two.)

A. Cisco Catalyst 3750B. Cisco Nexus 5596UPC. Cisco MDS 9148D. Cisco Catalyst 3560



QUESTION 31You deploy EMC Ionix UIM/P in a Vblock System.

Which two prerequisites must be met before proceeding with deployment of the appliance? (Choose two.)

A. vCenter Host Profiles configuredB. static IP from the logical configuration surveyC. EMC Ionix UIM/P OVFD. DHCP server



QUESTION 32What is a new feature of VMware vSphere 5.1?

A. ESXi hostB. vCenter Single Sign-OnC. VMware Update ManagerD. VMware Storage vMotion



QUESTION 33Which type of ODBC (DSN) connection is required for VMware Update Manager?

A. Microsoft SQL 64 bitB. Microsoft SQL User DSNC. Microsoft SQL 32 bit DSND. Microsoft File DSN



QUESTION 34What is the boot LUN size for an ESXi installation on a Vblock System 320?

A. 10 GBB. 20 GBC. 40 GBD. 60 GB


Explanation/Reference:Accurate.

QUESTION 35You are deploying a Vblock System and want to install recent patches to the ESXi host(s).

Which VCE recommended method would you use to complete this task?

A. esxcfgB. VMware Remote CLI power shellC. vicfgD. VMware Update Manager



QUESTION 36According to VCE, which three statements are regarded as best practice for vMotion deployment? (Choosethree.)

A. On each host, configure a VMkernel port group for vMotion.B. VMKernel port must be on the virtual machine management network.C. Use one dedicated GbE adapter for vMotion.D. Ensure that virtual machines have access to the same subnets on source and destination hosts.

E. Use jumbo frames configured through QoS.

Correct Answer: ADESection: (none)Explanation


QUESTION 37You are deploying a Vblock System and you are unable to log in to the vCenter server using single sign-on(SSO).

Which two steps should be verified? (Choose two.)

A. Log in credentials are correct.B. vCenter server is licensed.C. vCenter services are started.D. The single sign-on server is licensed.



QUESTION 38What information would be obtained about vmfs data stores under the Summary tab while connected to ahost in vSphere client? (Choose two.)

A. multipathing status for the data storeB. snapshotsC. hardware acceleration status eventsD. alarm actions status for the data store

Correct Answer: CDSection: (none)Explanation


QUESTION 39What is the VCE recommended approach on configuring the vCenter NTP server settings?

A. Configure the NTP settings through the VMware client GUI.B. Configure the NTP settings through scripts using the vSphere PowerCLI.C. Configure the NTP settings through the Web client.D. Configure the NTP settings through the VMware Update Manager.



QUESTION 40What are three core VMware components of a Vblock System? (Choose three.)

A. vCenter serverB. Update ManagerC. ESRSD. ESXE. ESXi

Correct Answer: ABESection: (none)Explanation


QUESTION 41Which three configuration parameters are available to create a virtual machine when performing a typicalinstallation? (Choose three.)

A. data store locationB. virtual disk sizeC. virtual machine hardware versionD. primary network connectionE. number of vCPUs

Correct Answer: ABDSection: (none)Explanation


QUESTION 42You want to use vMotion to move the entire state of a running virtual machine between hosts over adedicated vMotion network without service interruption.

What are two vMotion prerequisites before performing this task? (Choose two.)

A. Verify that you have at least two ESXi hosts that are licensed for vMotion or are in evaluation modeB. Verify that you have running instances of vCenter Server and the ESXi hosts are in maintenance mode.C. Verify that hosts have access to shared storage of a supported type, such as Fibre Channel, iSCSI, or

NASD. Verify that the source and destination hosts have specific Intel x86 CPUs.



QUESTION 43What are two expected results of the VMware vMotion test plan conducted by VCE at the completion of aVblock System build? (Choose two.)

A. No unexpected errors or faults occur.B. The secondary VSM takes over from the primary VSM.C. There will be minimal packet loss during vMotion.D. Traffic fails over to the redundant port channel each time a port-channel is disabled.



QUESTION 44What is a valid method to install EMC PowerPath/VE onto a VMware ESXi host?

A. Install using vCenter Update Manager (VUM).B. Install from the PowerPath/VE vCenter plug-in.C. Install remotely from the array management server.D. Install using the rpowermt command.



QUESTION 45What is a reason to use EMC Powerpath/VE on a Vblock System 720?

A. to provision storage from the vCenter clientB. to optimize load balancing on the storage fabricC. to add additional vStorage APIs for Array Integration (VAAI) featuresD. to optimize storage caching features on the ESXi host



QUESTION 46Where does a system administrator configure virtual machine affinity rules in VMware vCenter?

A. HA settingsB. DPM settingsC. virtual machine settingsD. DRS settings



QUESTION 47What are three possible results when enabling vSphere High Availability (HA)? (Choose three.)

A. Virtual machines will migrate from one host to another as resource availability changes.B. An ESXi host fails and some of the virtual machines restart on other hosts in the cluster.C. A virtual machine fails and automatically restarts on another host in the cluster.D. VMware vSphere Fault Tolerance will be enabled.

E. A virtual machine is unable to boot due to limited cluster resources.

Correct Answer: BCESection: (none)Explanation


QUESTION 48Using PowerPath/VE, which two details are expected outputs from the rpowermt display dev=all command?(Choose two.)

A. logical device IDB. serial number for the connected storage arrayC. initiator IDD. Fibre Channel switch details



QUESTION 49A host is a member of a high availability (HA) cluster in vCenter. There is a failure of a B-series blade in aVblock System 720.

What are three ways that vCenter is impacted? (Choose three.)

A. vCenter will recognize the host's absence and high availability will restart the virtual machines on theremaining hosts depending on resource constraints.

B. The vCenter virtual machine will restart on another available host, there will be no impact to productiondata on the Vblock.

C. vCenter will use Distributed Resource Scheduling (DRS) to vMotion virtual machines based on thereduced resources available.

D. The outage will require remediation to restore vCenter functionality.E. The amount of resources available to the cluster will be reduced until the outage is restored.

Correct Answer: ACESection: (none)Explanation


QUESTION 50What are three purposes of the master host in a vSphere high availability (HA) cluster? (Choose three.)

A. to monitor the state of slave hostsB. to monitor the power state of all protected virtual machinesC. to manage the lists of cluster hostsD. to migrate virtual machines when a vMotion is requestedE. to install the HA agent on newly added hosts

Correct Answer: ABCSection: (none)Explanation


QUESTION 51You observe that a host in a high availability (HA) cluster shows as disconnected within vCenter. The virtualmachines running on the disconnected host have not automatically restarted as expected.

What is the cause of this problem?

A. NTP was not configured on the HA cluster.B. vMotion is not enabled on the cluster hosts.C. The disconnected host was the master host.D. The host is still exchanging a data store heartbeat.



QUESTION 52A host has been placed into maintenance mode in a Distributed Resource Scheduler (DRS) enabled clusterfor patching. The virtual machines have not migrated as expected. DRS settings have been verified as fullyautomated at the cluster level.

What would cause this condition?

A. The selected host is using a different ESXi version than the rest of the cluster.B. vMotion is not enabled on the vMotion vmkernel interface for the selected host.C. The high availability agent has not been properly installed on the selected host.D. DNS is not enabled at the host level for the selected host.



QUESTION 53Which two statements are correct regarding VCE implementation of a persistent scratch partition? (Choosetwo.)

A. You must configure a persistent scratch partition on the boot-from-SAN VMFS data store.B. You must configure a persistent scratch partition on the boot-from-SAN NFS data store.C. Vblock Systems use centralized monitoring with syslog and SNMP in place of a persistent scratch

location.D. VCE uses the persistent scratch partition to ensure that critical log files are available.


Explanation/Reference:Modified now.

QUESTION 54On a Vblock System 720, what is the VCE supported tool used to manage a storage array?

A. Unisphere for VMAXB. Ionix ControlCenterC. Symmetrix System ViewerD. Symmetrix Management Console



QUESTION 55In a Vblock System 720, what is the maximum standard LUN size on an EMC Symmetrix VMAX10K/20K/40K?

A. 20 GBB. 64 GBC. 240 GBD. 2,457 GB



QUESTION 56In the Vblock System 720, what describes the VCE standard method of zoning?

A. multi initiator to single targetB. single initiator to multi targetC. single initiator to single targetD. multi initiator to multi target



QUESTION 57You are assigned to deploy a new host in a Vblock System, with block storage attached.

Which type of zoning would be performed on the Cisco 9148 switch to accomplish this task?

A. port zoningB. WWPN zoningC. symbolic node name zoningD. WWNN zoning



QUESTION 58You have just deployed a new ESXi host in a Vblock System 320 and only have TCP/IP available forstorage access.Which protocol would be used for data store access?

A. NFSB. CIFSC. iSCSID. FCP



QUESTION 59What is a zone set?

A. a collection of WWNs in a zoneB. a collection of zonesC. a collection of HBAs in a zoneD. a collection of Fibre Channel addresses in a zone



QUESTION 60Which two storage connectivity types are associated with block level access? (Choose two.)

A. NFSB. iSCSIC. CIFSD. FCP



QUESTION 61For which data type is NAS used?

A. block level accessB. file level accessC. fixed contentD. object content



QUESTION 62You are required to setup the network interface on a Vblock System 320 storage array, which is used for filelevel access.

In which mode should the interface be configured?

A. fail safe networkingB. link aggregationC. Ethernet channelD. network trunking



QUESTION 63How many parity disks are in a RAID 5 configuration?

A. 1B. 2C. 3D. 4


Explanation/Reference:Corrected.

QUESTION 64What information is displayed when an administrator uses the show vsan membership command on aCisco MDS switch?

A. information for a specific VSANB. membership information for all VSANsC. membership information for a specified VSAND. zone database information for a specific VSAN



QUESTION 65On a Vblock System 320, each VMware ESXi host will boot from a SAN-attached boot drive presented fromthe EMC VNX array.

Which statement is true according to VCE standards for boot LUNs?

A. Use Fibre Channel drives to create a RAID group, use RAID-5 4+1 RAID group, then create a 20 GB

LUN.B. Use Fibre Channel drives to create a RAID group, use RAID-5 7+1 RAID group, then create a 20 GB

LUN.C. Use SAS drives to create a RAID group, use RAID-5 4+1 RAID group, then create a 20 MB LUN.D. Use SAS drives to create a RAID group, use RAID-5 4+1 RAID group, then create a 20 GB LUN.



QUESTION 66What are three supported drive types for Vblock System 320 arrays? (Choose three.)

A. EFDB. SATAC. SASD. NL-SASE. FC

Correct Answer: ACDSection: (none)Explanation


QUESTION 67What is the hot spare drive requirement for a Vblock System 320 storage array?

A. Hot spare drives must exist for every 100 drives of any type drive in the array.B. Hot spare drives must exist for every 100 drives of the same type drive in the array.C. Hot spare drives must exist for every 30 drives of the same type drive in the array.D. Hot spare drives must exist for every 30 drives of any type drive in the array.



QUESTION 68On a Vblock System 720 storage array, LUNs are presented to a server through a masking view.

Which three components are included? (Choose three.)

A. initiator groupB. storage groupC. WWN groupD. LUN groupE. port group

Correct Answer: ABESection: (none)Explanation


QUESTION 69An ESXi host connected to a Vblock System 720 storage array requires a new 2 TB LUN.

According to VCE best practice, which type of device must be created to add to the host?

A. 4 member striped metaB. 4 member concatenated metaC. 8 member striped metaD. 8 member concatenated meta



QUESTION 70A SAN administrator must use the zone commit command to activate a zone set on a Cisco MDS 9148.

Which feature is enabled on the switch?

A. hardware zoning by access control listsB. enhanced zoningC. extended broadcast zoningD. basic zoning



QUESTION 71On the Vblock System 720, which two workload types require separate disk groups? (Choose two.)

A. RecoverPointB. bare metal bladesC. OracleD. SAP



QUESTION 72Which Cisco Unified Computing System (UCS) server model is a rack-mount server used in a VblockSystem?

A. A-SeriesB. B-SeriesC. C-Series

D. D-Series



QUESTION 73In Cisco UCSM, which policy allows you to enable the Cisco Discovery Protocol (CDP)?

A. Adapter PolicyB. Dynamic vNIC Connection PolicyC. QoS PolicyD. Network Control Policy



QUESTION 74What are three components of the Cisco UCS system that make up the Vblock System 320 compute layer?(Choose three.)

A. X-Blade Data MoversB. fabric interconnectC. Cisco Nexus switchD. fabric extendersE. chassis

Correct Answer: BDESection: (none)Explanation


QUESTION 75What is the number of domains required when deploying a Vblock System 720 with 16 UCS chassis on asingle pair of fabric interconnects?

A. 1B. 2C. 4D. 8



QUESTION 76You are asked to deploy a base configuration Vblock System 320.

How many Cisco UCS blades will be installed?

A. 2B. 4C. 8D. 16



QUESTION 77What are two supported link configurations between the Cisco 2208 I/O Module and the Cisco UCS6296UP fabric interconnects for a Vblock System 320? (Choose two.)

A. 2B. 4C. 8D. 16



QUESTION 78Which Vblock System component provides network connectivity and management capabilities to the CiscoUnified Computing System (UCS) blades and chassis?

A. fabric extenderB. fabric interconnectC. NXOSD. CIMC



QUESTION 79How many on-board unified ports does the Cisco Unified Computing System (UCS) 6296UP fabricinterconnect provide?

A. 48B. 62C. 96D. 97



QUESTION 80During a Vblock System 320 deployment, the implementation engineer needs to access UCS Manager toverify the compute configuration.

Which two IP addresses are used to open the GUI? (Choose two.)

A. the primary switch IP addressB. the secondary switch IP addressC. the virtual IP addressD. the CIMC IP address



QUESTION 81During a Vblock System 320 deployment, the customer wants to disassociate four half-width blades in asingle chassis for a future project.

Which tool is used to perform this compute reconfiguration?

A. vSphereB. CIMCC. UnisphereD. UCSM




QUESTION 82During a Vblock System 200 deployment, a single server did not power on and a replacement has beenreceived.

Which management interface is used to prepare the server for installation?

A. vSphereB. CIMCC. UnisphereD. UCSM



QUESTION 83At which link speed do the fabric extenders (FEX) within the Cisco UCS chassis connect to Cisco fabricinterconnects?

A. 2 GbEB. 4 GbEC. 8 GbED. 10 GbE



QUESTION 84During a Vblock System logical build, which three configuration changes require Unified Computing SystemManager (UCSM) access? (Choose three.)

A. fabric interconnect interfacesB. ESXi host Network Time ProtocolC. service profilesD. Cisco Nexus 1000VE. UCS Smart Call Home

Correct Answer: ACESection: (none)Explanation


QUESTION 85During a Vblock System logical build, which two management components within Unified ComputingSystem Manager (UCSM) require configuration with an IP address? (Choose two.)

A. fabric extenderB. fabric interconnectC. UCSMD. Cisco Nexus 5108 chassis



QUESTION 86A Vblock System 720 has been configured in the factory according to the VCE Logical Build Guide.

Which statement is correct?

A. Each service-profile should have at least one vNIC pinned to fabric interconnect A; one vNIC pinned tofabric interconnect B, and failover enabled.

B. Each service-profile should have at least one vNIC pinned to fabric interconnect A; one vNIC pinned tofabric interconnect B, and failover disabled.

C. Each service-profile should have at least one vHBA pinned to fabric interconnect A; one vHBA pinned tofabric interconnect B, and failover enabled.

D. Each service-profile should have at least one vHBA pinned to fabric interconnect A; one vHBA pinned tofabric interconnect B, and failover disabled.



QUESTION 87An engineer is deploying a Vblock System without using EMC's Unified Infrastructure Manager (UIM).Which three pools are required to be configured in Unified Computing System Manager (UCSM)? (Choosethree.)

A. Media Access Control (MAC) addressB. World Wide Port Name (WWPN)C. World Wide Node Name (WWNN)D. Cisco Integrated Management Controlled (CIMC)E. Management IP address

Correct Answer: ABCSection: (none)Explanation


QUESTION 88A customer uses EMC's Unified Infrastructure Manager (UIM) to deploy a Vblock System.

Which two post-deployment steps must the engineer take within Unified Computing System Manager(UCSM) to provide a VCE best-practice configuration? (Choose two.)

A. Set the Fibre Channel QoS policy in service profiles.B. Set the host firmware package in service profiles.C. Associate the service profiles to bladesD. Set enable failover for vNICs in service profiles.



QUESTION 89A Cisco Unified Computing System (UCS) blade encounters a hardware failure that requires the serviceprofile to be associated to another blade.

Once the service profile is associated to another blade, how does the host boot the existing operatingsystem?

A. The service profile maintains pointers to the local hard drives on the failed blade allowing true statelessmigration.

B. The service profile maintains the boot-policy to ensure the replacement blade boots to the existing LUN

on the storage array.C. The service profile migrates the hard drive content from the failed blade to the new blade during service

profile re-assignment.D. The service profile migration requires that the drives from the failed blade are physically migrated to the

replacement blade to boot the existing operating system.



QUESTION 90Which protocol is used to provide unified file storage connectivity to a Vblock System 320?

A. FCoEB. IPC. iSCSID. FC



QUESTION 91Which Cisco switch provides IP connectivity for the Vblock System 320?

A. Cisco Nexus 5548UPB. Cisco Catalyst 3750-XC. Cisco MDS 9148D. Cisco Nexus 2248TP



QUESTION 92Which switch in the network layer provides Fibre Channel (FC) links between the Cisco fabric interconnectsand the EMC VNX array in a Vblock System 320 segregated configuration?

A. Cisco MDS 9000 seriesB. Cisco Nexus 5000 seriesC. Cisco Nexus 7000 seriesD. Cisco UCS Fabric Interconnect



QUESTION 93

Which component connects a Vblock System 720 to a customer's network aggregation layer?

A. Cisco Nexus 5548UPB. Cisco Catalyst 3750-XC. Cisco MDS 9148D. Cisco UCS Fabric Interconnect 6296UP



QUESTION 94What is the requirement for adding VLANs to port channels for disjointed Layer 2 networks in a Cisco UCS?

A. VLANs must be explicitly assigned to an uplink.B. VLANs should not be explicitly assigned to an uplink.C. VLAN traffic must be allowed to travel over all uplinks.D. VLANs must be assigned in the 301-400 range.



QUESTION 95Which Cisco Nexus 5000 Series switch feature provides traffic prioritization and egress bandwidthallocation for a Vblock System 320 deployment?

A. Quality of Service (QoS)B. Data Center Ethernet (DCE)C. jumbo maximum transmission units (MTU)D. priority flow control



QUESTION 96Which Vblock System 320 component provides Fibre Channel network connectivity in a unified networkarchitecture?

A. Cisco MDS 9148B. Cisco Nexus 5548UPC. Cisco Nexus 1000VD. Cisco Catalyst 3750



Updated.

QUESTION 97In a Vblock System 320, which type of port channel is configured from the Cisco Nexus 5548 switch to thefabric interconnects?

A. static port channelB. virtual port channel (vPC)C. enhanced virtual port channelD. virtual port channel plus (vPC+)



QUESTION 98In Cisco UCS, what is a valid format of a vHBA World Wide Port Name?

A. 20:00:00:25:B5:01:0B:01B. 2000:0025:B501:0B01C. 20-00-00-25-B5-01-0B-01D. 20.00.00.25.B5.01.0B.01



QUESTION 99Which network capability does the Cisco Nexus 1000V provide in a Vblock System 720?

A. vNic driversB. IP address assignmentC. distributed switchingD. routing



QUESTION 100In a Vblock System 720, the Cisco Virtual Ethernet Module is installed on which component?

A. Cisco Nexus 1000VB. Cisco Nexus 5548UPC. VMware ESXi hostD. VMware vCenter server



QUESTION 101An administrator is unable to connect the Cisco Nexus 1000V to the vCenter server. The following error isdisplayed:{ERROR: [VMWARE-VIM] Extension key was not registered before its use.}

Which action would resolve this error?

A. From the Cisco Nexus 1000V, use the connect command.B. From the Cisco Nexus 1000V, use the vmware vc extension-key command.C. From VMware vCenter, create a new vSphere Distributed Switch.D. From VMware vCenter, register the Cisco Nexus 1000V xml plug-in.



QUESTION 102You are adding a new VLAN from the Cisco Nexus 1000V. You use the state enabled command.

What is the result of this command?

A. It creates a new VLAN in the Cisco Nexus 1000V.B. It creates a new VMkernel port in the ESXi host.C. It creates a new VLAN in the Cisco fabric interconnects.D. It creates a port group in the vCenter server.



QUESTION 103-- Exhibit ---- Exhibit --

Click the Exhibit button.

Which Vblock System 720 component is shown in the exhibit?

A. Cisco Catalyst 3750-XB. Cisco Nexus 5596UPC. Cisco Catalyst 3650D. Cisco Nexus 5020



QUESTION 104-- Exhibit --

-- Exhibit --Click the Exhibit button.

Vblock Systems have multiple power connector capabilities.

Which power receptacle is shown in the exhibit?

A. 30A 250V, 3 phase (NEMA L15-30P)B. 60A 250V,3 phase (IEC 60309)C. 60A 120V, 3 phase (IEC 60309)D. 30A 120V, 3 phase (C8303 L6-30P)





Vblock Systems have multiple power connector capabilities.

Which power receptacle is shown in the exhibit?

A. 60A 250V, single phase (IEC 60309)B. 60A 120V, 3 phase (IEC 60309)C. 60A 250V, 3 phase (IEC 60309)D. 30A 120V, 3 phase (C8303 L6-30P)



QUESTION 106When powering on a Vblock System what is the correct power up sequence?

A. Switches, AMP, SAN, UCS chassis, and UCS bladesB. Switches, SAN, UCS chassis, UCS blades, and AMPC. Switches, AMP, UCS chassis, UCS blades, and SAND. Switches, SAN, AMP, UCS chassis, and UCS blades


Explanation/Reference:Answer is renovated.

QUESTION 107What are three primary site survey considerations? (Choose three.)

A. Site informationB. Technical resourcesC. Customer power requirementsD. Data center physical auditE. Disaster recovery plan

Correct Answer: ACDSection: (none)Explanation


QUESTION 108Which EMC software is required to initialize a Vblock System 200 storage array?

A. Unisphere Service ManagerB. Unisphere Server UtilityC. VNX Installation AssistantD. Unisphere Client



QUESTION 109

Which three VLANs are required during the implementation of the Cisco Nexus 1000V in Layer 2 mode?(Choose three.)

A. native VLANB. control VLANC. management VLAND. system VLANE. packet VLAN

Correct Answer: BCESection: (none)Explanation


QUESTION 110In a Cisco Nexus 1000V, what is the default number of ports created in a vEthernet port profile?

A. 32B. 128C. 256D. 512



QUESTION 111After the installing the Cisco Nexus 1000V, the administrator uses the command show svs connections.

This command shows the connection status of which component?

A. ESXi hostB. vCenter serverC. Secondary Virtual Supervisor ModuleD. VMware Update Manager (VUM)



QUESTION 112What are three hardware components that make up the high availability Advanced Management Pod (HA-AMP)? (Choose three.)

A. Cisco Nexus 1000VB. Cisco Catalyst 3560C. EMC VNXeD. Cisco UCS C220E. Cisco Nexus 5548

Correct Answer: BCD

Section: (none)Explanation


QUESTION 113Your company wants to deploy a new Vblock System mini Advanced Management Pod (mini-AMP).

Which two hardware components are required? (Choose two.)

A. Cisco Catalyst 3560B. Cisco MDS 9148C. EMC VNXD. Cisco UCS C220



QUESTION 114A customer would like to add a new production VLAN to their Vblock System with UIM/P. The VLAN wasadded to the UIM/P service profile, and the connected Cisco Nexus 5000. The customer is still not able touse the new VLAN with a virtual machine.

Which step must the customer complete?

A. Create a new VSAN.B. Add the VLAN to Cisco Nexus 1000V.C. Add the VLAN to Cisco Catalyst 3560.D. Disable spanning tree on UCS.


Explanation/Reference:Rechecked, it's right.

QUESTION 115Which tool in the Advanced Management Pod (AMP) would a customer use to determine if their VblockSystem is compliant with a specific Release Certification Matrix (RCM)?

A. VMware Update ManagerB. VCE Vision Intelligent OperationsC. array management serverD. VMware vCenter Server Inventory Service



QUESTION 116A customer wants to ensure that the new installed Vblock System 320 storage array is being monitored by

EMC.

Which EMC monitoring tool must be installed to accomplish this?

A. Data Center Network Manager (DCNM)B. EMC Secure Remote Support (ESRS)C. EMC OnAlertD. ConnectEMC



QUESTION 117Which two steps are required to complete a Cisco UCS Smart Call Home registration on a Vblock System?(Choose two.)

A. After receiving the e-mail response from Cisco, click the link in the e-mail to complete registration forSmart Call Home.

B. Select "Send System Inventory Now" in UCSM.C. Configure UCSM to send periodic system inventory messages.D. Configure the SNMP trap destination.



QUESTION 118Which port is used for communication between EMC Secure Remote Support (ESRS) and the PolicyManager?

A. 443B. 5414C. 8090D. 8443



QUESTION 119You are backing up a Cisco UCS configuration.

Which parameter should you select to retain assigned vHBAs, WWPNs, vNICs MACs, WWNNs, andUUIDs?

A. Retain IdentitiesB. Preserve IdentitiesC. Include IdentitiesD. Copy Identities





Referring to the exhibit, which Vblock System 320 component is "A"?

A. Cisco Nexus 5000 Series switchB. Cisco Chassis containing blade serversC. UCS fabric interconnectD. Cisco MDS switches



QUESTION 121

-- Exhibit --


Referring to the exhibit, which Vblock System 320 component is "B"?

A. Cisco Nexus switchB. Cisco UCS fabric interconnectC. Cisco MDS switchD. Cisco fabric extender





Referring to the exhibit, which Vblock System 320 component is "C"?

A. Cisco Nexus SwitchB. Cisco MDS SwitchC. Cisco UCS fabric interconnectD. Cisco fabric extender



QUESTION 123In addition to the Logical Configuration Survey (LCS), which document is required prior to manufacturing aVblock System 720?

A. Configuration Reference GuideB. VCE change control formC. VCE Vblock Systems Release Certification MatrixD. EMC bin file request form

Correct Answer: D

Section: (none)Explanation


QUESTION 124For bare metal deployments, which statement ensures VCE is able to provide reasonable-effort support?

A. The ratio of bare metal to virtualized hosts cannot be more than 40 percent.B. A minimum of five virtualized hosts must be enabled.C. Bare metal workloads are run on separate physical spindles, disk groups, and pools.D. Systems cannot include hypervisor technologies other than VMware.



QUESTION 125Customers provide the information used to develop the Logical Configuration Survey (LCS) beforemanufacturing begins.

What information is required? (Choose two.)

A. syslog server IP addressB. NTP server IP addressC. method of device access (telnet or SSH)D. MIB browser IP address



QUESTION 126A storage administrator needs to access a Vblock System 200 storage array using EMC Unisphere GUI.

What information must the administrator obtain to log in?

A. the IP addresses of the two storage processorsB. the IP address of the service processorC. the IP address of the data moverD. the IP address of the x-blade



QUESTION 127What is the purpose of the EMC VNXe Connection Utility installed on the Vblock System 320 arraymanagement server?

A. to perform upgradesB. to configure the management IP addressC. to provision storageD. to troubleshoot performance issues



QUESTION 128You are installing a Vblock System 720 and notice that no Cisco UCS B230 blades are logging into theCisco MDS 9148 switches.

Which feature must be enabled on the Cisco MDS 9148 to resolve the issue?

A. NPIVB. TACACS+C. RADIUSD. NPV




Documents

VCE.Testkings.210-010.v2015-03-19.by.Gayle - GRATIS · PDF fileYou are deploying a Vblock System and want to install recent patches to the ESXi host(s). Which VCE recommended method