ES-401, Rev. 9 BWR Examination Outline Form ES-401-1
Facility Browns Ferry Date of Exam: -2013 A?r( 2.0r4-.RO K/A Category Points SRO-Only Points
Tier Group— — — —
KKKKKKAAAAG A2 G* Total1 2 3 4 5 6 1 2 3 4 * Total
1. i 4 3 3 4 3 20 4 3 7
Emergency &2 •T T i 2 1 i 7 2 1 3
Abnormal Plant — — — NIA N/A —
Evolutions Tier Totals 4 6 4 27 6 4 10
1 23322222332 26 3 2 5
2.2 1 1 1 11 2 11 1 1 1 12 0 2 1 3
Plant —
Systems Tier Totals 3 3 4 3 3 4 4 3 38 5 3 8
3. GenericKnowledgeandAbilities 1 2 3 4 10 1 2 3 4 7Categories 2 3 3 2 1 2 2 2
1. Ensure that at least two topics from every applicable K/A category are sampled within each tier of the ROand SRO-only outlines (i.e., except for one category in Tier 3 of the SRO-only outline, the Tier Totals”in each KIA category shall not be less than two).
2. The point total for each group and tier in the proposed outline must match that specified in the table.1’ The final point total for each group and tier may deviate by ± 1 from that specified in the table
based on NRC revisions. The final RO exam must total 75 points and the SRO-only exam must total 25 points.
7,L 3. Systems/evolutions within each group are identified on the associated outline; systems or evolutions that donot apply at the facility should be deleted and justified; operationally important, site-specific systems that arenot included on the outline should be added. Refer to ES-401, Attachment 2, for guidance regardingthe elimination of inappropriate K/A statements.
)O/14... 4. Select topics from as many systems and evolutions as possible; sample every system or evolutionin the group before selecting a second topic for any system or evolution.
?C 5. Absent a plant-specific priority, only those K/As having an importance rating (lR) of 2.5 or higher shall beselected. Use the RO and SRO ratings for the RO and SRO-only portions, respectively.
6. Select SRO topics for Tiers I and 2 from the shaded systems and K/A categories.
7. *The generic (G) K/As in Tiers I and 2 shall be selected from Section 2 of the K/A Catalog, but the topicsmust be relevant to the applicable evolution or system.
8. On the following pages, enter the K/A numbers, a brief description of each topic, the topics’ importanceratings (IRs) for the applicable license level, and the point totals (#) for each system and category. Enterthe group and tier totals for each category in the table above; if fuel handling equipment is sampled in otherthan Category A2 or G* on the SRO-only exam, enter it on the left side of Column A2 for Tier 2, Group 2 (Note#1 does not apply). Use duplicate pages for RO and SRO-only exams.
t.’ 9. For Tier 3, select topics from Section 2 of the K/A catalog, and enter the K/A numbers, descriptions, IRs,and point totals (#) on Form ES-401-3. Limit SRO selections to K/As that are linked to 10 CFR 55.43.
ES-401 2 Form ES-401-1
ES-401 BWR Examination Outline
Emergency and Abnormal Plant Evolutions - Tier 1/Group
Form ES-401-1
1-
E/APE#/Name/SafetyFunction K K K A A G K/ATopic(s) IR #
ta295001 Partial or Complete Loss of Forced
— ( A .I .03 —
Core Flow Circulation / 1 & 4 — —RS)1f\2.O4- —
295003 Partial or Complete Loss of AC / 6 — —R S)A1.o ($)cZI.7 —
295004 Partial or Total Loss of DC Pwr I 6 —— R)AAI.oI —295005 Main Turbine Generator Trip / 3 —
295006SCRAM/1 R —S .) A4j.03 ()Z ).2.o —
295016 Control Room Abandonment / 7p (p.) S2 .4.45 —
295018 Partial or Total Loss of CCW / 8 R — — () APt O9.- —
295019 Partial or Total Loss of Inst. Air / 8 — — —— 6 P. ) ( .. 4-. I (.) AIZ. D2 —
295021 Loss of Shutdown Cooling /4 — — —— R () —
295023 Refueling Acc /8 — — —
A 1<3 .03 —
295024 High Drywell Pressure / 5 (g) —
295025 High ReactorPressure/3 — — —
— cs) EA.D3 —
295026 Suppression Pool High Water ) A 1. 0Temp/S
295027 High Containment Temperature / s : : = : = — —
295028 High Drywell Temperature / 5 — — P. — — (.R) E K3 t)C, —
295030 Low Suppression Pool Wtr Lvi / 5 — PS — — — .2 . 0 \ —
295031 Reactor Low Water Level 12 — — R — — E 3. o2 —
and Reactor Power Above APRM R (p.) E-4. i. 04- 5) 2. —295037 SCRAM Condition Present
Downscale or Unknown / 1
295038 High Off-site Release Rate / 9 — R — ) E < 2. —
600000 Plant Fire On Site /8 — R — () ,A, o4 $) PAZ. 15
700000 Generator Voltage and Electric Grid R — S ) A41D3 (.5Disturbances / 6
K1A Category Totals: Z) 4 .3I 4II3 Group PointTotal: = 20/7
st-o
flE
S-40
1,R
EV
9T
1G1
BW
RE
XA
MIN
AT
ION
OU
TL
INE
FOR
ME
S-40
1-1
KA
NA
ME
/SA
FET
YFU
NC
TIO
N:
IRK
iK
21(
3K
41(
5K
6A
lA
2A
3A
4G
TO
PIC
:R
OS
PO
2950
01A
K1.
03Pa
rtia
lor
Com
plet
eL
oss
ofF
orce
d3.
64.
1El
ElEl
[1C]
ElEl
[][1
[]T
herm
allim
itsC
ore
Flow
Cir
cula
tion
/1
&4
295O
O3A
P2.O
4P
arti
alor
Com
plet
eL
oss
ofA
C/
63.
53.
7El
LIC]
LIC]
Elf
l[i
ElEl
ElS
yste
mli
neup
s
2950
04A
41.0
3Pa
rtia
lor
Tot
alL
oss
ofD
CPw
r/
63.
43.
6C]
[J[J
C]
C][]
[]El
ElEl
ElA
.C.
elec
tric
aldi
stri
butio
n
2950
05A
A1.
O1
Mai
nT
urbi
neG
ener
ator
Tri
p!3
3.1
3.3
ElEl
[]El
C]El
]C]
C]El
Rec
ircu
lati
onsy
stem
:P
lant
-Spe
cifi
c
2950
16G
2.4.
49C
ontr
olR
oom
Aba
ndon
men
t!7
4.6
4.4
C]El
ElEl
ElEl
LiEl
ElC]
Abi
lity
tope
rfor
mw
ithou
tre
fere
nce
topr
oced
ures
thos
eac
tion
sth
atre
quir
eim
med
iate
oper
atio
nof
syst
emco
mpo
nent
san
dco
ntro
ls.
2950
18A
A1.
02P
arti
alor
Tot
alL
oss
ofC
CW
/83.
33.
4[]
C]El
ElEl
Elll
ElEl
ElC]
Sys
tem
load
s
2950
19G
2.4.
1Pa
rtia
lor
Tot
alL
oss
ofIn
st.
Air
/8
4.6
4.8
ElEl
ElEl
ElEl
ElEl
ElEl
Kno
wle
dge
ofE
OP
entr
yco
ndit
ions
and
imm
edia
teac
tion
step
s.
2950
21A
A2.
02L
oss
ofS
hutd
own
Coo
ling
/4
3.4
3.4
ElEl
C]Li
C]El
ElEl
ElEl
RH
R/s
hutd
own
cool
ing
syst
emfl
ow-
-
2950
23A
K3.
03R
efue
ling
Acc
Coo
ling
Mod
e/
83.
33.
6El
C]El
[1El
ElEl
ElEl
ElV
entil
atio
nis
olat
ion
2950
24G
2.4.
3H
igh
Dry
wel
lP
ress
ure
/5
3.7
3.9
CIEl
LiEl
ElEl
Ufl
flC]
Abi
lity
toid
entif
ypo
st-a
ccid
ent
inst
rum
enta
tion
.-—
2950
25EA
2.O
5H
igh
Rea
ctor
Pre
ssur
e/
33.
43.
6El
LIEl
ElLI
ElEl
ElEl
[}D
ecay
heat
gene
rati
on.....
Pag
e1
of2
07/0
1/20
132:
00PM
Gen
erat
orV
olta
gean
dE
lect
ric
Gri
dD
istr
urba
ncec
s
ES
-401
,R
EV
9T
1G1
BW
RE
XA
MIN
AT
ION
OU
TL
INE
FOR
ME
S-4
01-1
KA
NA
ME
/SA
FET
YFU
NC
TIO
N:
IR1(
11(
21(
31(
41(
51(
6A
lA
2A
3A
4G
TOPI
C:R
OS
RO
2950
26EA
1.0l
Sup
pres
sion
Pool
Hig
hW
ater
Tem
p./
4.1
4.1
H[1
LILi
CLi
LILi
HLi
Sup
pres
sion
pool
cool
ing
2950
28EK
3.06
Hig
hD
ryw
ell
Tem
pera
ture
/5
3.4
LILi
ILi
LILi
LiLI
LiLI
[A
DS
2950
30EK
2.O
1Lo
wS
uppr
essi
onP
ool
Wtr
Lvi /
53.
83.
9Li
LiLi
LiLi
LiLi
LiLi
Li1I
PCI:
Pla
nt-S
peci
fic
2950
31EK
3.02
Rea
ctor
Low
Wat
erL
evel
/ 24.
44.
7J
Cor
eco
vera
ge
2950
37E
K1.
04S
CR
AM
Con
ditio
nP
rese
ntan
dP
ower
3.4
3.6
LiLi
LiLi
LILi
CLi
LiLI
Hot
shut
dow
nbo
ron
wei
ght:
Pla
nt-S
peci
fic
Abo
veA
PRM
Dow
nsca
leor
Unk
now
n/1
2950
38EK
2.06
Hig
hO
ff-s
iteR
elea
seR
ate
/9
3.4
3.7
CLI
LiC
HLi
LiC
CLi
Pro
cess
liqui
dra
diat
ion
mon
itori
ngsy
stem
6000
00A
K2.
04P
lant
Fire
On
Sit
e/8
2.5
2.6
LILi
LiC
LiLi
LiLi
LILi
Bre
aker
sI
rela
ys!
and
disc
onne
cts
2950
06A
K1.
03SC
RA
M/1
3.7
4.0
JLi
[1Li
LiLi
LiC
LiLi
HR
eact
ivity
cont
rol
7000
00A
KtO
33•
3s-”
llLi
LiLi
LiLi
LiLI
LiLi
LiU
nder
-exc
itat
kin
Pag
e2
of2
07/0
1/20
132:
00P
M
ES
-401
,R
EV
9T
1G
1B
WR
EX
AM
INA
TIO
NO
UT
UN
EFO
RM
ES-
401-
1
7000
00G
2.4.
9G
ener
ator
Vol
tage
and
Ele
ctri
cG
rid
Dis
trur
banc
ecs
Kno
wle
dge
oflo
wpo
wer
/sh
utdo
wn
impl
icat
ions
inac
cide
nt(e
.g.
LO
CA
orlo
ssof
RH
R)
miti
gatio
nst
rate
gies
.
KA
NA
ME
!SA
FET
YFU
NC
TIO
N:
Ki
K2
K3
K4
K5
K6
Al
A2
A3
A4
GT
OPI
C:
RO
SR
O
2950
04G
2.1
.7Pa
rtia
lor
Tot
alL
oss
ofD
CPw
r /6
4.4
4.7
F]Li
LILI
LILI
LIF],
LILI
Abi
lity
toev
alua
tepl
ant
perf
orm
ance
and
mak
eop
erat
iona
lju
dgm
ents
bas
edon
oper
atin
gch
arac
teri
stic
s,re
acto
rbe
havi
oran
din
stru
men
tin
terp
reta
tion
.
2950
06G
2.1.
20SC
RA
M/
14.
64.
6F]
UU]
LIF]
F]F]
Abi
lity
toex
ecut
epr
oced
ure
step
s.
—a1g
2950
19A
42.0
2Pa
rtia
lor
Tot
alL
oss
ofIn
st.
Air
/8
3.6
3.7
U]LI
LI[1
LILI
LILI
LILI
Sta
tus
ofsa
fety
-rel
ated
inst
rum
ent
air
syst
emlo
ads
(see
AK
2.1
-AK
2.19
)
2950
25EA
2.03
Hig
hR
eact
orP
ress
ure
/3
3.9
4.1
F]LI
LILI
LILI
HF]
HLI
Sup
pres
sion
pool
tem
pera
ture
2950
37E
A2.
05SC
RA
MC
ondi
tion
Pre
sen
tan
dP
ower
4.2
4.3
LILI
LILI
LILI
LIi
ElLI
LIC
ontr
olro
dpo
sitio
nA
bove
APR
MD
owns
cale
orU
nkno
wn
/1
6000
00A
A2.
15P
lant
Fire
On
Sit
e/8
2.3
3.5
LIL
LILI
LIU]
LILI
LILI
Req
uire
men
tsfo
res
tabl
ishi
nga
fire
wat
ch
3.84.2
LIL
ILIL
ILIL
1L
ILIL
ILI
Pag
e1
of1
07/0
1/20
132:
00P
M
ES-401 3 Form ES-401-1
ES-401 BWR Examination Outline Form ES-401-1Emergency and Abnormal °lant Evolutions - Tier 1/Group 2 (RD SRO)
=—= = = =—=— =
E/APE #1 Name! Safety Function K K K A A G K/A Topic(s) IR #1 2 3 1 2
295002 Loss of Main Condenser Vac / 3 & ) Afi2i
295007 High Reactor Pressure / 3
295008 High Reactor Water Level! 2R () A Z .02.
295009 Low Reactor Water Level / 2
295010 High Drywell Pressure!5 ‘$) —
295011 High Containment Temp /5— —
295012 High Drywell Temperature / 5— —
295013 High Suppression Pool Temp.! 5 — — — — — — —
295014 Inadvertent Reactivity Addition! 1
P)A.1\2.fl ——295015 Incomplete SCRAM / 1 — —
295017 High Off-site Release Rate! 9
295020 Inadvertent Cont. Isolation / 5 & 7 R c) A 1c3.
295022 Loss of CRD Pumps! 1
295029 High Suppression Pool Wtr Lvl / 5 — — — — — — — —
(\295032 High Secondary Containment
Area Temperature I 5— —
295033 High Secondary Containment R S (R) E Ai. D2Area Radiation Levels! 9 (5) A2.. P3295034 Secondary Containment
Ventilation High Radiation! 9 — —
295035 Secondary Containment High ( ‘. .A .01Differential Pressure! 5
295036 Secondary Containment HighSump/Area Water Level I 5 — —
500000 High CTMT Hydrogen Conc. ! 5 — —
K/A Category Point Totals: JjJ\]I)Q) j Group Point Total:
21
ES
-401
,R
EV
9T
1G2
BW
RE
XA
MIN
AT
ION
OU
TL
INE
FOR
ME
S-40
1-1
KA
NA
ME
!SA
FET
YFU
NC
TIO
N:
IRK
iK
2K
SK
4K
5K
6A
lA
2A
3A
4G
TO
PIC
:
RO
SR
O
2950
08A
K2.
02H
igh
Rea
ctor
Wat
erL
evel
123.
63.
8[1
flLI
JLI
[][J
[]R
eact
orfe
edw
ater
syst
em
2950
1402
.4.9
Inad
vert
ent
Rea
ctiv
ityA
dditi
on/
13.
84.
2LI
LIC]
LIC]
HLI
LIC]
Kno
wle
dge
oflo
wpo
wer
Ish
utdo
wn
impl
icat
ions
inac
cide
nt(e
.g.
LOC
Aor
loss
ofR
HR
)m
itiga
tion
stra
tegi
es.
2950
15A
A2.
O1
Inco
mpl
ete
SC
RA
M/i
4.1
4.3
LILI
LILI
LILI
LIJ
LIC]
LIR
eact
or
pow
er
2950
20A
K3.
03In
adve
rten
tC
ont.
Isol
atio
n/
5&
73.
23.
2j
LII
LILI
LILI
LILI
LILI
Dry
wel
L/c
onta
inm
ent
tem
per
ature
resp
onse
cetp
e’.
Yc)
2950
32E
K1.
03H
igh
Sec
ondar
yC
onta
inm
ent
Are
a3.
5•9
LILI
LILI
LILI
LILI
LI[]
Sec
onda
ryco
ntai
nmen
tle
akag
ede
tect
ion:
Pla
nt-
Tem
per
ature
/5
Spe
cifi
c
2950
33E
A1.
02H
igh
Sec
ondar
yC
onta
inm
ent
Are
a3.
73.8
LILI
LILI
LILI
IILI
LILI
LIP
roce
ssra
diat
ion
mon
itori
ngsy
stem
Rad
iat i
onL
evel
s/
9
2950
35E
A1.
01S
eco
nd
ary
Co
nta
inm
ent
Hig
h3.
63.
6H
LILI
LILI
LILI
LILI
LIS
eco
nd
ary
con
tain
men
tven
tila
tio
nsy
stem
Dif
fere
ntia
lP
ress
ure
/5
Pag
e1
of1
07/0
1/20
132:
00PM
ES
-401
,R
EV
9
KA
NA
ME
/SA
FET
YFU
NC
TIO
N:
2950
02A
A2.
01L
oss
ofM
ain
Con
dens
erV
ac/3
2950
10G
2.4.
20H
igh
Dry
wel
lP
ress
ure
/5
2950
33E
A2.
03H
igh
Sec
onda
ryC
onta
inm
ent
Are
aR
adia
tion
Lev
els/9
T1
G2
BW
RE
XA
MIN
AT
ION
OU
TU
NE
IRK
iK
2K
3K
4K
5K
6A
lA
2A
3A
4G
RO
SR
O
2.93.1E
1L
JL
1
3.8
4.3 &2L1L
1E
1D
C1L
1E
tJfl
E1L
1
FOR
ME
S-40
1-1
TO
PIC
:
Con
dens
erva
cuum
/abs
olut
epr
essu
re
Kno
wle
dge
ofop
erat
iona
lim
plic
atio
nsof
LO
Pw
arni
ngs,
caut
ions
and
note
s.
Cau
seof
high
area
radi
atio
n
Pag
e1
of1
07/0
1/20
132:
00P
M
ES-401 4 Form ES-401-1
ES-401 BWR Examination O!ttiQeF—... Form ES-401-1
—
— PlantSystems-Thr2/Groupl((RO){’SRO)
System #/Name K K K K K K A A A A G K/ATopic(s) IR #12 34561 23_
203000 RHRILPCI: Injection K S (IZ) A4-:03 $) 3SMode
205000 Shutdown Cooling —
— —— (2) i.s,o2 —
206000 HPCI —R — R
207000 Isolation (Emergency) — — ,_) /Condenser — —
2O9001LPCS R (13)Ki.l4 —
209002HPCS = = = : : =:: —
211000SLC R CR) M-.04- —
212000RPS —
()A2.O3 —
2150031RM R p)R303 —
215004 Source Range Monitor (.R) A3 oa.
215005APRM/LPRM (K) k3,O7 cS)A’2.OS —
217000 RCIC -A40 —
218000ADS (RRI.o3 —
223002 PCIS/Nuclear Steam R () /‘3 .0 —
Supply Shutoff ) &Z,4. J
239002 SRVs R () 2 4.46 —
259002 Reactor Water Level () 14.4-.0I —
Control
261000SGTS ($)2.2.4- —
262001 AC Electrical P. () —
Distribution
262002 UPS (AC/DC) R •) (1) Go3 —
263000 DC Electrical P. R I 0 () AZ • 02. —
Distribution — (Ps) k, .0)
264000 EDGs — — — — 1.— ) k,03 —
300000 Instrument Air — — — — — —— P. (f A3.0 —
400000 Component Cooling B’) iL2. oa (5) A2 . olWater
K/A Category Point Totals: !ZO i2 3 13 1 2 12 I i 3 i3 l Group Point Total: 26/5
5p-D 3 2.
T2G
1B
WR
EX
AM
INA
TIO
NO
UT
LIN
EFO
RM
ES-
401-
1E
S-4
01,
RE
V9
KA
NA
ME
/SA
FET
YFU
NC
TIO
N:
IRK
iK
2K
3K
4K
5K
6A
lA
2A
3A
4G
TO
PIC
:R
OS
RO
2030
00A
4.03
RH
R/L
PCI:
lnje
ctio
nM
ode
3.4
3.4
jj
Kee
pfil
lsy
stem
2050
001(
5.02
Shu
tdow
nC
oolin
g2.
82.
9[]
fl[]
[][]
[)[]
Val
veop
erat
ion
2060
001(
3.02
HPC
I3.
83.
8[1
El]
ElEl
ULi
ElUI
[]R
eact
orpr
essu
reco
ntro
l:B
WR
-23,
4
2060
001<
5.07
HPC
I2.
82.
8cJ
ElEl
ElEl
ElLI
UU]
ClS
yste
mve
ntin
g:B
WR
-2,3
,4
2090
01K
I.14
LPC
S3,
73.
8Li
[1C]
LIEl
El[J
[]U]
[]R
eact
orvess
2110
00A
4.04
SLC
4.5
4.6
U]U]
[][]
U]U]
U]U]
[][
[]R
eact
orpo
wer
2120
00A
2.03
RP
S3.
33.
5El
U]El
ElC]
U]LI
C]C]
flS
urve
illa
nce
test
ing
2150
031(
3.03
IRM
3.7
3.7
U]U]
U]U]
U]U]
C]C]
[][]
Rod
cont
rol
and
into
rmat
ion
syst
em:
Pla
nt-S
peci
fic
2150
04A
3.02
Sou
rce
Ran
geM
onito
r3.
43.
3U]j
U]U]
U]U]
U]U]
U]U]
Ann
unci
ator
and
alar
msi
gn
als
2150
051<
3.07
AP
RM
IL
PRM
3.2
3.3
U]j
U]U]
U]C]
U]U]
ElLI
Rod
bloc
km
onit
or:
Pla
nt-S
peci
fic
2170
00A
4.08
RC
IC3.
73.
6C]
Elfl
ElEl
U]El
U]U]j
C]S
yste
mflo
w
Pag
e1
of3
07/0
1/20
132:
00P
M
Cn
nE
S-4
01,
RE
V9
T2G
1B
WR
EX
AM
INA
TIO
NO
UT
LIN
EFO
RM
ES
-401
-1K
AN
AM
E!
SAFE
TY
FUN
CT
ION
:IR
KI
K2
K3
K4
1(5
K6
Al
A2
A3
A4
GT
OPI
C:
RO
SR
O21
7000
K2.
02R
CIC
2.8
2.9
]J
RC
ICin
itiat
ion
sign
als
(log
ic)
2180
00K
1.03
AD
S3.7
3.8
[j
jJ[]
Nuc
lear
boile
rin
stru
men
tsy
stem
2230
02A
3.O
1P
CIS
/Nuc
lear
Ste
amS
uppl
yS
huto
ff3.
43.
4fl
Sys
tem
indi
cati
ngli
ghts
and
alar
ms
2230
02G
2.4.
31P
CIS
/Nuc
lear
Ste
amS
uppl
ySh
utof
f4.
24.
1[]
fl[]
[][]
[][]
[[]
Kno
wle
dge
ofan
nunc
iato
rsal
arm
s,in
dic
atio
ns
orre
spon
sepr
oced
ures
2390
02G
24.4
6S
RV
s4.
24.
2[J
[][]
-flj
JA
bilit
yto
veri
fyth
atth
eal
arm
sar
eco
nsis
tent
with
the
plan
tco
ndit
ions
.
2590
02K
4.O
1R
eact
orW
ater
Lev
elC
ontr
ol3.
03.
1D
EEl
HE
ElEl
ElE
nsur
ing
adeq
uate
NPS
Hfo
rre
circ
ulat
ion
pum
ps:
Pla
nt-
Spe
cifi
c
2610
00A
1.O
1S
GT
S2.
93.
1El
ElEl
ElEl
ElEl
ElEl
ElS
yste
mfl
ow
2620
011<
4.03
AC
Ele
ctri
cal
Dis
trib
utio
n3.
13.
4El
ElEl
ElEl
ElEl
ElIn
terl
ocks
betw
een
auto
mat
icbu
str
ansf
eran
dbr
eake
rs
2620
02A
204
UP
S(A
C/D
C)
3.2
3.4
flEl
ElEl
ElEl
El]
El[]
ElA
bnor
mal
batt
ery
oper
atio
n:B
WR
-I
2620
021<
603
UP
S(A
C/D
C)
2.7
2.9
ElEl
El1—
]Li
1El
ElEl
ElE
lS
tati
cin
vert
er
2630
00A
1.O
1D
CE
lect
rica
lD
istr
ibut
ion
2.5
2.8
El[1
LiLI
LIEll
[1El
ElEl
Bat
tery
char
ging
/dis
char
ging
rate
Pag
e2
of3
07
/01
/20
13
2:00
PM
ES
-401
,R
EV
9T
2G1
BW
RE
XA
MIN
AT
ION
OU
TL
INE
FOR
ME
S-40
1-1
KA
NA
ME
/SA
FET
YFU
NC
TIO
N:
IRK
iK
2K
3K
4K
5K
6A
lA
2A
3A
4G
TO
PIC
:R
OS
RO
2630
00K
2O1
DC
Ele
ctri
cal
Dis
trib
utio
n3.
13.
4H
E]H
HLI
HH
[]fl
flM
ajor
D.C
.lo
ads
2640
00K
6.03
EO
Gs
3.5
3.7
LILI
HLI
LiI
HLI
LILIj
Lub
eoi
lpu
mps
3000
00A
3.02
Inst
rum
ent
Air
2.9
2.7
HLI
LILI
El[1
LIH
IILI
LIA
irte
mpe
ratu
re
4000
O0<
2.02
Com
pone
ntC
ooli
ngW
ater
2.9
2.9
LIf
LIH
LILI
LIH
LILI
Li
CC
Wva
lves
n
Page3of3
07/0
1/20
132:
00P
M
flTh
T2G
1B
WR
EX
AM
INA
TIO
NO
UT
LIN
EE
S-4
01,
RE
V9
FOR
ME
S4O
1-1
KA
NA
ME
/SA
FET
YFU
NC
TIO
N:
IRX
lK
2K
3K
4K
5K
6A
lA
2A
3A
4G
TO
PIC
:
RO
SR
O
2030
00G
2.2.
38R
HR
ILPC
I:In
ject
ion
Mod
e3.
64.
5Li
LiLi
[][]
r]fl
[1{—
]fl
[]K
now
ledg
eof
cond
itio
nsar
idlim
itatio
nsin
the
faci
lity
lice
nse.
2150
05A
205
AP
RM
IL
PR
M3.
53.
6Li
Li[]
[][]
[]Li
[][]
[]L
oss
ofre
circ
ulat
ion
flow
sign
al
2610
00G
2.2.
4S
GT
S3.
63.
6[J
LiLi
LiLi
LiLi
[]Li
Li]
(mul
ti-u
nit)
Abi
lity
toex
plai
nth
eva
riat
ions
inco
ntro
lbo
ard
layo
uts.
syst
ems,
inst
rum
enta
tion
and
pro
ced
ura
lac
tIon
sb
etw
een
unit
sat
afa
cili
ty.
2630
00A
2.02
DC
Ele
ctri
cal
Dis
trib
utio
n2.
62.9
LiLi
LiLi
LiLi
Li]
LiLi
LiL
oss
ofve
ntil
atio
ndu
ring
char
gin
g
4000
00A
2.01
Com
ponen
tC
ooli
ngW
ater
3.3
3.4
[][
[]]
LiLi
Li[]
LiLi
LiL
oss
ofC
CW
pum
p
Pag
e1
of1
07/0
1/20
132:
00P
M
ES-401 5 Form ES-401-1
ES-401 BWR Examination Outr Form ES-401-1
== Plant Systems- er2iGrou20 SRO
System #1 Name K K K K K K A A A A G K/A Topic(s) IR #1 234 561 2 34
201001 CRD Hydraulic — —— R — —
— (R) ‘
201002 RMCS — —
— .) /‘2 .04 —
201 003 Control Rod and DriveMechanism
201004 RSCS
201005 RCIS
201006 RWM ) t.I.04-
202001 Recirculation
202002 Recirculation Flow Control
204000 RWCU
2I4000RPIS — —
— g )cz4..34 —
215001 Traversing In-core Probe — — — — — — — — —
215002 RBM —— (.S)A2.D2.
216000 Nuclear Boiler Inst. — — —— — (L.) A 3.01 —
21 9000 RHR/LPCI: Torus/Pool CoolingMode
223001 Primary CTMT and Aux. — — — — —
226001 RHR/LPCI: CTMT Spray Mode
230000 RHR/LPCI: Torus/Pool Spray R (f.) A4, 08Mode
233000 Fuel Pool Cooling/Cleanup
234000 Fuel Handling Equipment (1k) A, 02. —
23900 1 Main and Reheat Steam
239003 MSIV Leakage Control
241000 Reactor/Turbine Pressure 5 (5) ‘2.4. 3D
Regulator
245000 Main_Turbine_Gen._/ Aux.
256000 Reactor Condensate
259001 Reactor Feedwater k 113. W.-.4-. oa
268000 Radwaste
271000 Offgas c A2.09272000 Radiation Monitoring R () K.03
286000 Fire Protection
288000 Plant Ventilation R 03
290001 Secondary CTMT
290003 Control Room HVAC ft (R 14 3v3290002 Reactor Vessel Internals () 1<5, OS
K/A Category Point Totals: Ro L LILI iJT I I Group Point Total: ]cR.c?
0E
S-40
1,R
EV9
nT
2G2
BW
RE
XA
MIN
AT
ION
OU
TL
INE
HL
iHH
LIH
LIH
LI
FOR
ME
S-4
01-1
KA
NA
ME
/SA
FET
YFU
NC
TIO
N:
IRK
lK
2K
31(
4K
SK
BA
lA
2A
3A
4G
TO
PIC
:R
OS
RO
2010
011(
6.06
CR
0H
ydra
ulic
2.8
2.8
LILI
[][J
[[]
[][]
[JC
ompo
nent
cool
ing
wat
ersy
stem
s:P
lant
-Spe
cifi
c
2010
02A
2.04
RM
CS
3.2
3.1
LILI
H[]
[7LI
LI[]
LIC
ontr
olro
dbl
ock
2010
061(
1.04
RW
M3.
13.
2f]
HH
[1[1
LI[J
LILI
L]H
Ste
amfl
ow/r
eact
orpo
wer
P-S
pec(
Not
-BW
R6)
2140
00G
2.4.
34R
PIS
4.2
4.1
H[]
LILI
HLI
[]K
now
ledg
eof
RO
task
spe
rfor
med
outs
ide
the
mai
nco
ntro
lro
omdu
ring
anem
erge
ncy
and
the
resu
ltan
top
erat
iona
lef
fect
s21
6000
A3.
01N
ucle
arB
oile
rIn
st.
3.4
3.4
LiH
HH
HLI
HH
HR
elat
ions
hip
betw
een
met
er/r
ecor
der
read
ings
and
actu
alpa
ram
eter
valu
es:
Pla
nt-S
peci
fic
2300
00A
4.08
RH
R/L
PCI:
Tor
us/P
ool
Spr
ayM
ode
3.0
2WLi
HLI
HLI
HH
LIH
IILi
Pum
p/sy
stem
disc
harg
epr
essu
re
2340
00A
1.02
Fuel
Han
dlin
gE
quip
men
t3.
33.
8H
LIEl
LILI
HLI
LIH
HR
efue
lfl
oor
radi
atio
nle
vels
/air
born
ele
vels
2590
01K
4.02
Rea
ctor
Fee
dwat
er2.
82.
9LI
ElH
iILI
LIH
HH
LILi
Fee
dwat
erhe
atin
g
2720
001(
2.03
Rad
iati
onM
onito
ring
2.5
2.8
LILI
LIH
LILI
LI[1
LI[El
Sta
ckga
sFa
diat
ion
mon
itori
ngsy
stem
2880
001(
6.03
Pla
ntV
entil
atio
n2.
72.
7H
LiH
LILI
LILI
LILI
HP
lant
air
syst
ems
2900
021(
5.05
Rea
ctor
Ves
sel
Inte
rnal
s3.
13.
3B
ritt
lefr
actu
re
Pag
e1
of2
07/0
1/2
013
2:0
0P
M
nE
S-4
01,
RE
V9
T2G
2B
WR
EX
AM
INA
TIO
NO
UT
LIN
EFO
RM
ES-
401-
1
KA
NA
ME
/SA
FET
YFU
NC
TIO
N:
IRK
iK
2K
3K
4K
5K
6A
lA
2A
3A
4G
TO
PIC
:
RO
SR
O
2900
031(
3.03
Con
trol
Roo
mH
VA
C2.
93.
1LI
III
LI[]
LI[]
LILI
[][I
Con
trol
room
tem
pera
ture
Pag
e2
of2
07/0
1/20
132:
00PM
FOR
ME
S-40
1-1
TO
PIC
:
Los
sor
redu
ctio
nin
reci
rcul
atio
nsy
stem
flow
(flo
wco
mpa
rato
r):
BW
R-3
,4,5
Kno
wle
dge
ofev
ents
rela
ted
tosy
stem
oper
atio
ns/s
tatu
sth
atm
ust
bere
port
edto
inte
rnal
orgi
niza
tion
sor
outs
ide
agen
cies
.
Val
vecl
osur
es
ES
-401
,R
EV
9T
2G2
BW
RE
XA
MIN
AT
ION
OU
TL
INE
KA
NA
ME
/SA
FET
YFU
NC
TIO
N:
Ki
K2
K3
K4
K5
K6
Al
A2
A3
A4
G
RO
SR
O
2150
02A2
.02RB
M3.3
3.3Li
LiLi
LILI
Li(]
ElLI
LI
2410
00G
2.4.
30R
eact
or/T
urbi
neP
ress
ure
Reg
ulat
or2.
74.
1LI
LILi
LiLI
LiLI
LiLi
LI
2710
00A
2.09
Off
gas
2.6
2.8
Pag
e1
of1
07/0
1/20
132:
00P
M
1
ES-401 Generic Knowledge and Abilities Outline (Tier 3) Form ES-401-3
Facility: rOlA.M R4kf Date of Exam: Aic1 Ol4
Category K/A # Topic
IR
2.1. I L,oc.A Swirc.k5, th-5,
1. 2.1.3 (c-k-Conduct 2.1.of Operations
2123 .Ccc- Qwed-’ 4.4-
Subtotal (•;)2.2.15 p kS /ci1c/ô .
2.2.22 LCC’5 q-e-+, t- 4o2. 2.2.3g hvu/it,iuWs I\ 2,12EquipmentControl 2.2.
2.242. L-Cs I*4. .4kij i;64 4.722.38 c £la - 4._cSubtotal - C..)2.3.7 PM) P5 - /. b-’zQ 3, 5
2.3.13 P -JeJvrcL3. 2.3.14 /téti Razc
-
Radiation JControl 2.3.
2.3.’ flQL2 p441.dfc
2.3. 13 ILA I lIst 3Subtotal (:) ()2.4.1 ti1 c/pOA c-s 4C
4. 2.4.45 vz6t 4Emergency 2.4.Procedures!
2.4.4Q 45
:Subtotal
Tier3PointTotal (i5 10 7
RO
SR
OT3
BW
RE
XA
MIN
AT
ION
OU
TL
INE
ES
-401
,R
EV
9
KA
NA
ME
!SA
FET
YFU
NC
TIO
N:
IRK
i1(
2K
31(
4K
5K
6A
lA
2A
3A
4G
TO
PIC
:
G2.
1.31
Con
duct
ofop
erat
ions
4.6
4.3
[][]
[][]
FOR
ME
S4O
1-1
:A
bfllt
yto
loca
teco
ntro
lro
omsw
itch
es,
cont
rols
and
indi
catio
nsan
dto
dete
rmin
eth
atth
eyar
eco
rrec
tly
refl
ectin
gth
ede
sire
dpl
ant
lineu
p.
G2.
1.39
Con
duct
ofop
erat
ions
3.6
4.3
LILi
LiLi
[1[1
11Fl
LiLi
Kno
wle
dge
ofco
nser
vati
vede
cisi
onm
akin
gpr
acti
ces
62
.2.1
5E
quip
men
tC
ontr
ol3.
94.
3[
[LI
[]j
[]A
bilit
yto
dete
rmin
eth
eex
pect
edpl
ant
conf
igur
atio
nus
ing
desi
gnan
dco
nfig
urat
ion
cont
rol
docu
men
taio
n
62.2
.22
Equ
ipm
ent
Con
trol
4.0
4.7
LiLi
LiLi
LiLi
LILI
LiLi
Kno
wle
dge
oflim
iting
cond
itio
nsfo
rop
erat
ions
and
safe
tylim
its.
G2238
Equ
ipm
ent
Con
trol
3.6
4.5
LiLi
LiLi
Li[]
Kno
wle
dge
ofco
ndit
ions
and
limita
tions
inth
efa
cilit
yli
cens
e.
G2.
3.13
Rad
iati
onC
ontr
ol3.
43.
8Li
LiLi
LiLi
[][]
[][]
Kno
wle
dge
ofra
diol
ogic
alsa
fety
proc
edur
espe
rtai
ning
toli
cens
edop
erat
ordu
ties
62.3
.14
Rad
iati
onC
ontr
ol3.
43.
8Li
LiLi
[]F
]Li
LiLI
LiLi.
Kno
wle
dge
ofra
diat
ion
orco
ntam
inat
ion
haza
rds
that
may
aris
edu
ring
norm
al,
abno
rmal
,or
emer
genc
yco
ndit
ions
orac
tivi
ties
62.3
.7R
adia
tion
Con
trol
3.5
3.6
LiLi
LiLi
LiLi
LiLi
LiLi
Abi
lity
toco
mpl
yw
ithra
diat
ion
wor
kpe
rmit
requ
irem
ents
duri
ngno
rmal
orab
norm
alco
ndit
ions
62.4
.1E
mer
genc
yP
roce
dure
slP
lans
4.6
4.8
Li[1
LiLi
LiLi
LiLi
LiLi
Kno
wle
dge
ofE
OP
entr
yco
ndit
ions
and
imm
edia
teac
tion
step
s.
62.4
.45
Em
erge
ncy
Pro
cedu
res/
Pla
ns4.
14.
3Li
LiLi
LiLi
LiLi
LiLi
LiA
bilit
yto
prio
ritiz
ean
din
terp
ret
the
sign
ific
ance
ofea
chan
nunc
iato
ror
alar
m.
Pag
e1
of1
07/0
1/20
132:
00P
M
0/f
lE
S-4
0I,
REV
9T
3B
WR
EXA
MIN
ATI
ON
OU
TLIN
EFO
RM
ES-
401-
1K
AN
AM
E/S
AFE
TY
FUN
CTI
ON
:IR
—K
lK
2K
31(
4K
5K
6A
lA
2A
3A
4G
TO
PIC
:R
OS
RO
G2.
1.23
Con
duct
ofop
erat
ions
4.3
4.4
fi[J
flrj
[j
[]fi
Abi
lity
tope
rfor
msp
ecif
icsy
stem
and
inte
grat
edpl
ant
—pr
oced
ures
duri
ngal
lm
odes
ofpl
ant o
pera
tion
.
G2.
2.22
Equ
ipm
ent
Con
trol
4.0
4.7
fifi
fifi
fifij
Kno
wle
dge
oflim
iting
cond
itio
nsfo
rop
erat
ions
and
safe
tylim
its.
G2.
2.38
Equ
ipm
ent
Con
trol
3.6
4.5
[j
[][)
fi[]
fi[]
[]fi
[JK
now
ledg
eof
cond
itio
nsan
dlim
itatio
nsin
the
faci
lity
lice
nse.
G2.
3.13
Rad
iati
onC
ontr
ol3.
43.
8fi
fiEl
rifl
flK
now
ledg
eof
radi
olog
ical
safe
typr
oced
ures
pert
aini
ngto
lice
nsed
oper
atoi
duti
es
G2.
3.6
Rad
iati
onC
ontr
ol2.
03.
8El
ElEl
ElEl
ElLi
fiA
bilit
yto
apro
vere
leas
epe
rmit
s
G2.
4.40
Em
erge
ncy
Pro
cedu
res/
Pla
ns2.
74.
5El
LIEl
LIfi
[JEl
flK
now
ledg
eof
the
SR
Os
resp
onsi
bili
ties
inem
erge
ncy
plan
impl
emen
tati
on.
G2.
4.42
Em
erge
ncy
Pro
cedu
res/
Pla
ns2.
63.
8[]
fifi
fiEl
fi[
ElEl
Kno
wle
dge
ofem
erge
ncy
resp
onse
faci
litie
s.
Pag
e1
of1
07/0
1/20
132:
00PM
ILT 1306 Administrative Topics Outline Form ES-301-1
Facility: Browns Ferry NPP Date of Examination: 4/28/20 14
Examination Level: RO / SRO Operating Test Number: 1404
Administrative Topic Type Describe activity to be performedCode
*
Conduct of Operations N 2.1.29 For restoring an HCU to service determines valve sequencing,
SRO/RO Ala required position, verification requirements, and torque requirements.
N 2.1.26 Determine Electrical Safety requirements and the correctprocedure to Rack Out 480V SD BD 2A Compartment 2B.
Conduct of Operations D 2.1.7 2-SR-2 Drywell Floor and Equipment Drain Log Calculation
SRO/RO Alb N 2.1.5 NFRESOMs Shift Staffing
Equipment Control N 2.2.15 Perform Condensate Panel Lineup Checklist for Control Room
SRO/RO A2 D 2.2.37 Maintenance Rule Availability for EECW and RHRSW
Radiation Control D 2.3.4 Determine Stay Time under Emergency Conditions and
SRO A3 authorize
Emergency Plan D 2.4.43 EPIP-5 Appendix B and C Notifications
RO/SRO A4 .
D 2.4.4 1 Emergency Action Level Classification
NOTE: All items (5 total) are required for SROs. RO applicants require only 4 items unless theyare retaking only the administrative topics, when all 5 are required.* Type Codes & Criteria: (C)ontrol Room
(D)irect from bank (< 3 for ROs; <4 for SROs and RU retakes)
(N)ew or (M)odified from bank ( 1)
(P)revious 2 exams ( 1; randomly selected)
(S)imulator
ILT 1306 Administrative Topics Outline Form ES-301-1
Reactor Operator
1. For restoring an HCU to service determines valve position, sequencing, verificationrequirements, and torque requirements.
• New
• 1-01-85, Control Rod Drive System and NPG-SPP-1O.3, Verification Program
• For restoring an HCU to service determines valve lineup sequence, required position,verification required and ‘torque requirements.
• 2.1.29 Knowledge of how to conduct system lineups, such as valves, breakers, switches, etc.Importance RO 4.1
2. Calculate the correct Drywell Floor and Equipment Sump leakage using 2-SR-2
• Direct from Bank
• 2-SR-2 Instrument Checks and Observations) (Applicant Handout)
• Calculates the correct Drywell Floor and Equipment Sump leakage using 2-SR-2 and thendetermines that unidentified leakage is outside the acceptance criteria.
• 2.1.7 Ability to evaluate plant performance and make operational judgments based onoperating characteristics, reactor behavior, and instrument interpretation. Importance RO 4.4
3. Performs Condensate Panel Lineup Checklist for Control Room
• New
• 213-01-2 Attachment 2
• Performs Condensate Panel Lineup Checklist in order to ensure the Condensate Systemcomponents are in the required position on Control Room Panels for Condensate Systemstartup.
• 2.2.15 Ability to determine the expected plant configuration using design and configurationcontrol documentation, such as drawings, line-ups, tag-outs, etc. Importance RO 4.5
4. EPIP-5, Appendix B and C Activation of ERO and State Notffications
• Direct from Bank
• EPIP-5, General Emergency
• Completion of ERO Activation and State Notification in accordance with Appendix B andAppendix C of EPIP-5.
• 2.4.43 Knowledge of emergency communications systems and techniques. Importance RO 3.2
ILT 1306 Administrative Topics Outline Form ES-301-1
Senior Reactor Operator
1. Determine Electrical Safety requirements and the correct procedure to Rack Out 480V SDBU 2A Compartment 2B
• New
• 0-GOI-300-2, Electrical and 11-300, Electrical Safe Work Practices
• Determine correct section of 0-GOI-300-2 that is required to Rack Out the breaker and theElectrical Safety PPE and Protective Boundary requirement.
• 2.1.26 Knowledge of industrial safety procedures (such as rotating equipment, electrical, hightemperature, high pressure, caustic, chlorine, oxygen, and hydrogen). Importance SRO 3.6
2. NFR ESOMs Shift Staffing
• New
• Using ESOMs the SRO determines who is available and who would be in violation of theFatigue Rule lAW NPG-SPP-3.21.
• 2.1.5 Ability to use procedures related to shift staffmg, such as minimum crew complement,overtime limitations, etc. Importance SRO 3.9
3. Determine the effect that a loss of sump pumps in an RIIRSW room has on Operability andMaintenance Rule Availability of RIIRSW and EECW Pumps
• Direct from Bank
• 0-11-346, Maintenance Rule Performance Indicator Monitoring, Trending and Reporting
• Technical Specification 3.7.1 and 3.7.2
• Determines that a loss of both sump pumps in an RHRSW Room makes the three pumps inthat room Inoperable and Unavailable. Determines Technical Specification actions conditionrequired 3.7.1 Condition A, B, C, and E required actions A.2, B.1, CA, and E.1.
• 2.2.3 7Ability to determine operability and/or availability of safety related equipment.Importance SRO 4.6
4. Determination of Stay Time and Approving Authority to perform an emergencyevolution to save equipment.
• Direct from Bank
• EPIP 15, Emergency Exposure
• Determine amount of time an operator has to perform an emergency evolution due toradiation levels and authorize on the correct form.
• 2.3.4 Knowledge of radiation exposure limits under normal and emergency conditions.Importance SRO 3.7
ILT 1306 Administrative Topics Outline Form ES-301-1
5. Emergency Action Level Classification
• Direct from Bank
• EPIP-l and 5 Emergency Classification Procedure and General Emergency
• Complete Notification Handouts Appendix A
• 2.4.41 Knowledge of emergency action level thresholds and classifications. Importance SRO4.6
C
ES-301 Control Roomlln-Plant Systems Outline Form ES-301-2
Facility: Browns Ferry NPP Date of Examination: 4/28/2014
Exam Level: RO I SRO-I I SRO-U Operating Test No.: 1404
Control Room Systems@ (8 for RO); (7 for SRO-I); (2 or 3 for SRO-U, including I ESF)
System I JPM Title Type Code* SafetyFunction
a. Dual Recirc Pump Quick Restart N, L, S 1
b. RFPT Trip Recovery Unit 3 only N, L, S 2
c. Respond to a Stuck Open SRV Unit 2 only A, M, 5 3
d. Loss of Shutdown Cooling A, D, L, S 4
e. Emergency Containment Venting D, EN, S 5
f. Trip the Turbine, Generator PCB Failure to Open A, L, N, S 6
g. Cross-Tie CAD to Drywell Control Air A, D, S 8
h. Off-Gas Post-Treatment Radiation HI-HI-HI ( RO Only) P, S 9
In-Plant Systems@ (3 for RO); (3 for SRO-l); (3 or 2 for SRO-U)
i. Alternate RPV Injection PSC Pumps D, R, E 2
j. Shutdown Cooling in Service lAW CR Abandonment N, R, E 7
k. Align 480V RMOV BD 3B and Start RHR Pump 3A A, U, E 8
© All RO and SRO-I control room (and in-plant) systems must be different and serve different safetyfunctions; all 5 SRO-IJ systems must serve different safety functions; in-plant systems and functionsmay overlap those tested in the control room.
* Type Codes Criteria for RO I SRO-l I SRO-U
(A)lternate path 4-6/2-3
(C)ontrol room
(D)irect from bank <91<81<4
(E)mergency or abnormal in-plant 1I 1I1
(EN)gineered safety feature - / - 1>1 (control room system)
(L)ow-Power I Shutdown ?1I?1I1
(N)ew or (M)odified from bank including 1 (A) > 2/> 2/>1
(P)revious 2 exams 3/ 3/ 2 (randomly selected)
(R)CA >1/>1/>1
(S)imulator
ILT 1306 Control Roomiln-Plant Systems JPM Narrative
Control Room Systems:
a. Dual Recirc Pump Quick Restart (Unit 2 or 3)
• New / Simulator / Low Power
.2/3-01-68, Reactor Recirculation System
• 202001 Recirculation System A4.01 Ability to manually operate and/or monitor in thecontrol room: Recirculation pumps IMPORTANCE: RO 3.7 SRO 3.7
• Operator directed to perform dual Recirculation Pump quick restart lAW 2/3-01-68, theoperator will start both Recirculation Pumps.
b. RFPT Trip Recovery (Unit 3)
• New / Simulator / Low Power
• 3-01-3, Reactor Feedwater System
• 259001 Reactor Feedwater System A201. Ability to (a) predict the impacts of the followingon the Reactor Feedwater System; and (b) based on those predictions, use procedures tocorrect, control, or mitigate the consequences of those abnormal conditions or operations:Pump trip. IMPORTANCE: RO 3.7 SRO 3.7
• The operator places an Alternate RFPT in service lAW 3-01-3 section 8.1 and restores ReactorLevel.
c. Responds to a stuck Open SRV (Unit 2 Only)
• Alternate path / Modified from Bank / Simulator
• 2-AOl-I-i, Relief Valve Stuck Open
239002 Relief I Safety Valves A2.03 Ability to (a) predict the impacts of the following onthe Relief I Safety Valves; and (b) based on those predictions, use procedures to correct,control, or mitigate the consequences of those abnormal conditions or operations: Stuckopen SRV IMPORTANCE: RO 4.1 SRO 4.2
• Responds to a stuck open SRV JAW 2-AOl-i-i, when the relief valve fails to close from thecontrol room proceeds to backup control panel in the Unit 2 simulator and performs actions toclose SRV.
ILT 1306 Control Roomlln-Plant Systems JPM Narrative
d. Restore Shutdown Cooling (Unit 2 or 3)
• Direct from Bank / Alternate Path I Low Power / Simulator
• 2/3-AOI-74-1 Loss of Shutdown Cooling, 2/3-ARP-9-3D
• 295021 Loss of Shutdown Cooling AA1.02 Ability to operate andlor monitor thefollowing as they apply to Loss of Shutdown Cooling: RHRlshutdown coolingIMPORTANCE: R03.5 SRO3.5
• Operator is directed to restore shutdown cooling following an inadvertent RPS actuation,will commence restoration of shutdown cooling with RHR Pump B. After RHR Pump B isstarted, the RHR System II Pump B Seal Leakage High alarm will be received. Inaccordance with the ARP the operator will secure RHR B pump and establish cooldownwith RHR D pump JAW with the AOl for loss of Shutdown Cooling.
e. Emergency Containment Venting (Unit 2 or 3)
• Direct from Bank / ENgineered Safety Feature / Simulator
• 2/3-EOI Appendix-13 Emergency Venting Primary Containment
• 295024 High Drywell Pressure EA1.19 Ability to operate and/or monitor the following asthey apply to High Drywell Pressure: Containment atmosphere control: Plant-SpecificIMPORTANCE: RO 3.3 SRO 3.4
• The operator vents the Drywell and Suppression Chamber through the hardened suppressionchamber vents lAW 2/3 -EOI Appendix- 13.
f. Trip the Turbine, Generator PCB Fails to Open (Unit 2 or 3)
• New / Simulator I Low Power / Alternate path
• 2/3-AOI-100-1, Reactor Scram
• 262001 AC Electrical Distribution A2.01 Ability to (a) predict the impacts of the followingon the AC Electrical Distribution; and (b) based on those predictions, use procedures tocorrect, control, or mitigate the consequences of those abnormal conditions or operations:Turbine I generator trip IMPORTANCE: RO 3.4 SRO 3.6
• Operator trips the Main Turbine and when the Generator PCB fails to open the operatortakes actions to open the Generator PCB lAW 2/3 -AOl- 100-1.
ILT 1306 Control Roomlln-Plant Systems JPM Narrative
g. Cross-Tie CAD to Drywell Control Air (Unit 2 and 3)
• Direct from Bank / Simulator / Alternate Path
• 2/3-EOI Appendix-8G Crosstie CAD to Drywell Control Air
• 295019 Partial or Complete Loss of Instrument Air AA1 .01 Ability to operate and / ormonitor the following as they apply to Partial or Complete Loss of Instrument Air: BackupAir Supply IMPORTANCE: RO 3.5 SRO 3.3
• Operator crossties CAD to Drywell Control Air JAW 2/3-EOI Appendix-8G. When CADSystem A shows indications of being depressurized the operator isolates CAD System A.
h. Off-Gas Post-Treatment Radiation HI-HI-HI (RO Only) (Unit 2 or 3)
• Previous / Simulator
• 2/3-ARP-9-4C, Window 35• 2/3 -AOI-66-2, Offgas Post-Treatment Radiation HI-HI-HI• 271000 Offgas System A2.04 Ability to (a) predict the impacts of the following on the
OFFGAS SYSTEM; and (b) based on those predictions, use procedures to correct, control,or mitigate the consequences of those abnormal conditions or operations: Offgas systemhigh radiation IMPORTANCE: RO 3.7 SRO 4.1
• Operator is directed to respond to Offgas Post-Treatment Radiation HI-HI-HI alarm inaccordance with 2/3-ARP-9-4C Window 35. Then the operator refers to 2/3-AOI-66-2,Offgas Post-Treatment Radiation HI-HI-HI, and perform the actions of 2/3-AOI-66-2 inserta core flow runback and reactor scram. Operator will then shut the MSIVs.
In-Plant Systems:
i. Alternate RPV Injection PSC Pumps
• Direct from Bank / Emergency or Abnormal In-Plant / RCA Entry
• 1-EOI Appendix-7G, Alternate RPV Injection System Lineup Pressure SuppressionChamber Head Tank Pumps
• 295031 Reactor Low Water Level EA1 .08 Ability to operate and / or monitor the followingas they apply to REACTOR LOW WATER LEVEL: Alternate injection systems: Plant-Specific IMPORTANCE: RO 3.8 SRO 3.9
• Simulates aligning PSC Pumps for alternate injection LAW 1-EOI Appendix-7G. When thePSC Pumps fail to start, the operator drains the PSC Tank Level switch.
ILT 1306 Control Roomlln-Plant Systems JPM Narrative
j. Shutdown Cooling in Service lAW CR Abandonment
• New / Emergency in Plant / RCA Entry
• 1-AOI-100-2, Control Room Abandonment
• 295016 Control Room Abandonment AA1.07 Ability to operate and/or monitor thefollowing as they apply to Control Room Abandonment: Control Room / local controltransfer mechanisms IMPORTANCE: RO 4.2 SRO 4.3
• Simulates placing Shutdown Cooling in service from outside the control roomJAW l-AOI-l00-2.
k. Align 480V RMOV Board 3B and Start RUR Pump 3A
• Direct from Bank / Emergency in Plant / Alternate Path
• 0-SSI-16, Control Building Fire EL 593 through EL 617
• 600000 Plant Fire on Site AA2.16 Ability to determine and interpret the following as theyapply to Plant Fire on Site: Vital equipment and control systems to be maintained andoperated during a fire IMPORTANCE: RO 3.0 SRO 3.5
• Simulates field actions to align 480V RMOV Board 3B and to start RHR Pump 3A forinjection, JAW 0-SSI-16. When the 3A RHR Pump fails to start the operator will utilize thenote to start RHR Pump 3A with the pushbutton on the breaker.
Facility: Browns Ferry NPP Scenario No.: NRC —4 Op-Test No.: 1404
Examiners:___________________ Operators: SRO:___________________
______________
ATC:______________
_______________
BOP:______________
Initial Conditions: 80% power, RFPT 3B and A3 RHRSW Pumps are tagged out.
Turnover: Alternate Refuel and Reactor Zone Fans lAW 3-OI-30A and 30B. Raise power to 85%
with flow and hold for RFPT 3B repairs.
Event Maif. No. Event Type* Event Description
No.
Alternate Refuel and Reactor Zone Fans JAW 3-OI-30A
1N-BOP and 30B, Refuel damper 64-9 fails in mid position when
TS-SRO Refuel Fans are in Off and is Open when Refuel Fansoperating
R-ATC2 Commence power increase with flow to 85%
R-SRO
C-ATC
3 edlOb C-BOP Loss of 480V SD BD 3B
TS-SRO
C-BOP4 Batch File Stator Water Cooling Pump trip
C-SRO
5 fw30a RFPT 3A Governor fails low
I-ATC6 tcl0b
1SR0EHC Pressure Transducer failure
7 Batch File M-ALL ATWS
8 Batch File M-ALL LOCA Loss of RPV Water Level
9 hpO7 C Loss of HPCI 120 VAC Power Supply
* (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor
Critical Tasks - Five
With reactor scram required and the reactor not shutdown, to prevent an uncontrolled RPV
depressurization and subsequent power excursion, inhibit ADS.
1. Safety Significance:Precludes core damage due to an uncontrolled reactivity addition.
2. Cues:Procedural compliance.
3. Measured by:ADS logic inhibited prior to an automatic initiation unless all required injection systems are
Terminated and Prevented.
4. Feedback:RPV pressure trend.
RPV level trend.ADS “ADS LOGIC BUS A/B 1NHLBITED” annunciator status.
With a reactor scram required and the reactor not shutdown, initiate action to reduce power by injecting
boron (If still critical with challenge to BuT) and inserting control rods.
1. Safety Significance:Shutting down reactor can preclude failure of containment or equipment necessary for the safe
shutdown of the plant.
2. Cues:Procedural compliance.
Suppression Pool temperature.
3. Measured by:Observation - If operating lAW EOI- I and C-5, US determines that SLC is required (indicated by
verbal direction or EOI placekeeping action) before exceeding 110 degrees in the Suppression
Pool.
ANDRO places SLC A / B Pump control switch in ON, when directed by US.
ANDControl Rod insertion commenced in accordance EOI Appendixes.
4. Feedback:Reactor Power trend.
Control Rod indications.
SLC tank level.
\ \\
Critical Tasks - Five
During an ATWS, when conditions with Emergency Depressurization required, Terminate and Prevent
RPV injection (except for CRD, SLC and RCIC) from ECCS and Feedwater until reactor pressure is
below the MARFP as directed by US.
1. Safety Significance:Prevention of fuel damage due to uncontrolled feeding.
2. Cues:Procedural compliance.
3. Measured by:Observation - No ECCS injection prior to being less than the MARFP.
AND
Observation - Feedwater terminated and prevented until less than the MARFP.
4. Feedback:Reactor power trend, power spikes, reactor short period alanns.
Injection system flow rates into RPV.
With RPV pressure <MARFP, slowly increase and control injection into RPV to restore and maintain
RPV level above TAF as directed by US.
1. Safety Significance:Maintaining adequate core cooling and preclude possibility of large power excursions.
2. Cues:Procedural compliance.
RPV pressure indication.
3. Measured by:Observation - Injection not commenced until less than MARFP, and injection controlled such that
power spikes are minimized, level restored and maintained greater than TAF.
4. Feedback:RPV level trend.RPV pressure trend.
Injection system flow rate into RPV.
Critical Tasks — Five
When Suppression Chamber Pressure exceeds 12 psig, initiate Drywell Sprays while in the safe region of
the Drywell Spray Initiation Limit (DSTL) curve and prior to exceeding the PSP limit.
1. Safety Significance:Precludes failure of containment
2. Cues:Procedural compliance
High Drywell Pressure and Suppression Chamber Pressure
3. Measured by:Observation - US directs Drywell Sprays JAW with EOI Appendix 1 7B
ANDObservation - RO initiates Drywell Sprays
4. Feedback:Drywell and Suppression Pressure lowering
RHR flow to containment
OR
Before Drywell temperature rises to 280°F, initiate Drywell Sprays while in the safe region of the
Drywell Spray Initiation Limit (DSIL) curve.
1. Safety Significance:Precludes failure of containment
2. Cues:Procedural compliance
High Drywell Pressure and Suppression Chamber Pressure
3. Measured by:
Observation - US directs Drywell Sprays lAW with EOI Appendix 1 7B
ANDObservation - RO initiates Drywell Sprays
4. Feedback:Drywell and Suppression Pressure lowering
RI{R flow to containment
\\)\\c
Events
1. BOP operator will alternate Refuel and Reactor Zone Fans JAW 3-O1-30A and 30B. Refueldamper 64-9 fails in mid position when Refuel Fans are in off and is open when Refuel Fansoperating. Tech Spec 3.6.4.2 Condition A, required action A.1 and A.2.
2. ATC commences power increase 85% using recirculation flow.
3. The Crew will respond to a loss of 480V SD BD 3B, this will cause a loss of RPS B, loss of 480V
RMOV BDs 3B and 3C. The Inboard MSIV A will have inadvertently closed. The crew will need
to lower power to meet the main steam line flow guidance JAW 3 -AOI-3 -1. The crew will need torestore power to 480V SD BD 3B, reset RPS, reset PCIS and restore systems. The SRO will alsohave to enter the following AOIs; 3-AOI-l-3, 3-AOI-70-l, and 3-AOJ-99-1. SRO will refer to theTRM and determine Technical Surveillance Requirement 3.4.1.1 to monitor Reactor CoolantConductivity continuously cannot be met and samples must be drawn every 4 hours. SRO willrefer to Tech Spec 3.6.1.3 for failed closed MS1V and enter condition A. SRO will refer to TechSpec 3.4.5 and determine Condition B is required for inoperable containment atmosphericmonitoring equipment.
4. The running Stator Water Cooling Pump will trip and the standby pump will fail to AUTO start.The BOP operator will be required to start the standby Stator Water Cooling pump to restoresystem flow and prevent an automatic Turbine Trip/Reactor scram.
5. RFPT 3A flow controller will slowly fail low, RFPT 3A speed will continue to decrease until theATC or Crew notices. The controller will fail to respond until the ATC takes manual control withhandswitch. The Operator will be able to restore RFPT 3A speed in manual. SRO should directentry into 3 -AOI-3 -1.
6. An ATWS will occur on the scram and the power supply to HPCI will fail, leaving RCIC as theonly source of high pressure makeup besides SLC and CRD. The crew will insert control rodsmanually, and maintain reactor level.
7. With RCIC, CRD and SLC as the only source of high pressure makeup as the LOCA degradesRPV Level will continue to lower. The SRO will determine Emergency Depressurization isrequired to restore RPV Level. The crew will ED and restore RPV Level with available systems.
Terminate the scenario when the following conditions are satisfied or upon request of Lead Examiner:
Control Rods are being inserted
Emergency Depressurization complete
Reactor Level is restored
SCENARIO REVIEW CHECKLIST
SCENARIO NUMBER: 4
9 Total Malfunctions Inserted: List (4-8)
2 Malfunctions that occur after EOI entry: List (1-4)
4 Abnormal Events: List (1-3)
2 Major Transients: List (1-2)
2 EOI’s used: List (1-3)
2 EOI Contingencies used: List (0-3)
75 Validation Time (minutes)
5 Crew Critical Tasks: (2-5)
YES Technical Specifications Exercised (Yes/No)
Scenario Tasks
TASK NUMBER K/A RO SRO
Alternate Reactor and Refuel Zone Fans
RO U-30A-NO-02 288000 A4.01 3.1 2.9
Raise Power with Recirc Flow
RO U-000-NO-06 202002 A4.07 3.3 3.3
SRO S-000-AD-3 1
Scenario Tasks
TASK NUMBER &Q S±Q
Loss of 480V SD BD 3B
RO U-57B-AL-06 262001 A2.04 3.8 4.2
SRO S-57B-AL-09
Reactor Feed Pump Turbine Governor Failure
RO U-003-AL-09 259002 A4.01 3.8 3.6
SRO S-003-AB-01
Stator Water Cooling Pump Trip
RO U-35A-AL-02 245000 A4.03 2.7 2.8
SRO 5-070-AB-Ol
EHC Pressure Transducer Failure
RO U-047-AB-02 241000 A2.03 4.1 4.2
SRO S-047-AB-02
LOCA/Low Level ED
RO U-003-AL-24 295031 EA2.04 4.6 4.8
RO U-000-EM-0 1
SRO S-000-EM-14
SRO S-000-EM-15
SRO 5-000-EM-Ol
ATWS
RO U-000-EM-03 295015 AA2.01 4.1 4.3
RO U-000-EM-22
RO U-000-EM-28
SRO S-000-EM-03
SRO S-000-EM-18
NRC Scenario 5
( ci1ity: Browns Ferry NPP
PvorniflflrL’
Scenario No.: NRC —5
Operators: SRO:_
ATC:
BOP:
Op-Test No.:
Initial Conditions: 100% power, DG D and RBCCW 2B Pump are tagged out. Spare RBCCW Pump isaligned for operation.
Turnover: Return LPRM 8-49B to Operate from a Bypassed Condition lAW 2-OI-92B. Lower Power withflow to 90% for Main Turbine Valve Testing.
Event Maif. No. Event Type* Event DescriptionNo.
N-BOP1 Return LPRM 8-49B to Operate lAW 2-OI-92B
N-SRO
R-ATC2 Commence power decrease with flow to 90%
R-SRO
C-BOP3 edl8a Loss of I&C Bus A
TS-SRO
R-ATC
4 adOic TS-SRO ADS SRV 1-22 leaking
C-BOP
C-ATC VFD Cooling Water Pump 2A trips with failure of the standby5 thl8a
C-SRO pump to auto start
C-ATCLOCA - Recirculation Pump 2A Inboard and Outboard seal
6 thlO/1 laR-ATC
failureTS-SRO
Two Level instruments fail high tripping Feedwater and HPCI /7 Batch File M-ALL
LOCA / ED on Reactor Level
8 edl0a C Loss of 480V SD Board 2A
RHR and Core Spray Division 2 Injection Valves will not Auto9 Batch I open
10 rcO8 C RCIC Steam Valve fails to Auto open
* (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor
1
NRC Scenario 5
Critical Tasks - Three
With RPV pressure below the Shutoff Head of the available Low Pressure system(s), operate availableLow Pressure system(s) to restore RPV water level above T.A.F. (-162 inches).
1. Safety Significance:Maintaining adequate core cooling.
2. Cues:Procedural compliance.Pressure below low pressure ECCS system(s) shutoff head.
3. Measured by:Operator manually starts initiates at least one low pressure ECCS system and injectsinto the RPV to restore water level above -162 inches.
4. Feedback:Reactor water level trend.Reactor pressure trend.
With an injection system(s) operating and the reactor shutdown and at pressure, after RPV water leveldrops to -162 inches, transition to Emergency Depressurization before RPV level lowers to-180 inches.
1. Safety Significance:Maintain adequate core cooling, prevent degradation of fission product barrier.
2. Cues:Procedural compliance.Water level trend.
3. Measured by:Observation - At least 6 SRV’s opened
4. Feedback:RPV pressure trend.SRV status indications.
2
NRC Scenario 5
Critical Tasks — Three
To prevent an uncontrolled RPV depressurization when Reactor level cannot be restored and maintainedabove -162 inches, inhibit ADS.
1. Safety Significance:Maintain adequate core cooling, prevent degradation of fission product barrier.
2. Cues:Procedural compliance.
3. Measured by:ADS logic inhibited prior to an automatic initiation.
4. Feedback:RPV pressure trend.RPV level trend.ADS “ADS LOGIC BUS A/B iNHIBITED” annunciator status.
3
NRC Scenario 5
Events
1. BOP operator will return LPRM 8-49B to Operate lAW 2-OI-92B.
2. ATC lowers power to 90% using recirculation flow.
3. The crew will respond to a momentary loss of I&C Bus A. The in-service SJAE (A) will isolateand numerous alarms will come in. The BOP operator will shift SJAE’s to B or reset SJAE Aand return to service lAW 2-01-66 or 2-AOI-47-3. Reactor Zone Differential pressure low willalarm and the operator will have to reset Refuel and Reactor Zone fans. When one of the SJAE’sare restored high H2 will result in Off Gas, the SRO will evaluate IRM 3.7.2 and enterCondition A. The H202 analyzer will isolate requiring the SRO to evaluate TRM 3.3.11 and3.6.2. The Drywell CAM will isolate requiring the SRO to evaluate Tech Spec 3.4.5.
4. During I&C Bus A loss, Main Steam Relief Valve open will alarm. When power is restored toI&C Bus A the alarm will clear but ADS SRV 1-22 will be leaking by and the acoustic monitorwill indicate the leak by. SRO should enter 2-AOl-i-i, the ATC will lower power to less than90%. When power is below 90% the BOP operator will perform 2-AOl-i-i actions to attempt toclose the SRV. SRO will refer to Tech Specs and determine TS 3.5.1 condition F is applicable.
5. The VFD Cooling Water Pump for the A Reactor Recirc VFD will trip and the standbypump will fail to start. The ATC will start the standby VFD Cooling Water Pump torestore cooling water preventing a VFD and Reactor Recirc Pump trip.
6. #1 and #2 recirc pump seal failure — ATC will note alarm and report #2 seal carrying full
pressure. A short time later seal #2 will fail ATC will note that a small LOCA exists. ATC will
trip and isolate A RR Pump lAW with 2-AOI-68-1A. ATC will insert control rods to exit Region
2 of the power to flow map. SRO will determine Technical Specification 3.4.1 Condition A, is
applicable again with 24 hours to establish single loop conditions.
7. Level instruments 208A and 208D will fail high, causing a high level trip of Main Turbine,RFPTs and HPCI. RCIC will be the only major source of high pressure injection and the steamsupply valve to RCIC will fail to auto open. The Crew will maintain reactor level until theLOCA is beyond the ability of RCIC to control. The SRO will determine ED is required in orderto restore level with available low pressure systems.
8. After the scram 480V Shutdown Board 2A will fail due to a lockout, this will prevent operationof Core Spray Division 1 System for injection. RHR Loop 1 may be used for injection but nothrottle capability with exist. RHR Loop 1 will not be available for Containment coolingoperation.
9. With Division 2 Accident logic bypassed RHR and Core Spray will not auto start on anyaccident signals. The crew will have to manually start pumps and open injection valves. RI-JRLoop 2 will be available for Containment Cooling functions until required for injection.
4
NRC Scenario 5
Terminate the scenario when the following conditions are satisfied or upon request of Lead Examiner:
Emergency Depressurization complete
Reactor Level is restored
SCENARIO REVIEW CHECKLIST
SCENARIO NUMBER: 5
10 Total Malfunctions Inserted: List (4-8)
4 Malfunctions that occur after EOI entry: List (1-4)
4 Abnormal Events: List (1-3)
1 Major Transients: List (1-2)
2 EOI’s used: List (1-3)
2 EOI Contingencies used: List (0-3)
75 Validation Time (minutes)
3 Crew Critical Tasks: (2-5)
YES Technical Specifications Exercised (Yes/No)
\\ \\1
5
NRC Scenario 5
Scenario Tasks
TASK NUMBER EQ SEQ
Restore an LPRM from Bypass
RO U-92B-NO-05 215005 A4.04 3.2 3.2
Lower Power with Recirc Flow
RO U-068-NO-03SRO S-000-AD-31 2.1.23 4.3 4.4
Loss of I&C Bus A
RO U-57C-AB-03 262001 A2.04 3.8 4.2SRO S-57C-AB-03
ADS SRV leaking
RO U-001-AB-01 239002 A2.03 4.1 4.2SRO S-001-AB-01
VFD Cooling Water Pump Failure
RO U-068-AL-19 202001 A2.22 3.1 3.2SRO S-068-AB-01
RR Pump Seal Failure
RO U-068-AL-09 202001 A2.10 3.5 3.9SRO S-068-AB-01
Loss of 480V SD BD 2A
RO U-57B-AL-06 262001 A4.05 3.3 3.3SRO S-57B-NO-07
LOCA/Low Level ED
RO U-003-AL-24 295031 EA2.04 4.6 4.8RO U-000-EM-01RO U-000-EM-13SRO S-000-EM-14SRO S-000-EM- 15SRO S-000-EM-01
6
Facility: Browns Ferry NPP Scenario No.: NRC - 6 Op-Test No.:
Examiners:__________________ Operators: SRO:_________
_____________
ATC:
______
_____________
BOP:______
Initial Conditions: 1.3% power, operating in 2-GOI-100-1A Section 5.4 steps 63.3 and 65.
Turnover: Warm RFPT B lAW 2-01-3, section 5.6 and then Continue to pull rods for ModeChange.
Event Maif. No. Event Event DescriptionNo. Type*
1 Warm RFPT B lAW 2-01-3, section 5.6
R-ATC2 R-SRO
Raise power with Control Rods
C-ATC Control Rod will difficult to withdraw, control rod at position3 rd05r3847 C-SRO otherthanOO
4 dOEC-ATC Control Rod will triple notch after drive water header pressure
rTS-SRO is raised and then will remain stuck, mispositioned control rod
dC-BOP Loss of 480V Unit Board 2A, failure of EHC Pump 2B to auto
5 e 07aC-SRO start
6 rcO 1 One level instrument fails and RCIC inadvertently starts
7 batch M-ALL SSI Fire 25-1
8 hpO3 I HPCI Flow controller will not operate in Auto
9 batch C Numerous instrument failures due to SSI Fire
* (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor
Critical Tasks — Three
Within 10 minutes of recorded time in SSI an Operator has placed Path A Vent Flow Controller,2-FIC-84-20, in MANUAL and 0 SCFM, at Panel 2-9-55.
1. Safety Significance:Maintaining adequate RHR Pump NPSH.
2. Cues:Procedural compliance.Containment Pressure indication.
3. Measured by:Observation - 2-FIC-84-20 in manual and set at 0 SCFM.Observation - 2-FCV-84-20 closed.
4. Feedback:Containment Pressure trend.No flow through A vent path.
Within 10 minutes of recorded time in SSI an Operator has initiated a controlled 100°F per hourcooldown rate using HPCI and relief valves as required.
1. Safety Significance:Prevent Drywell Temperature from exceeding design basis temperature.
2. Cues:Procedural compliance.Reactor Pressure indication.
3. Measured by:Observation - HPCI in Pressure Control Mode.Observation - SRVs opened to lower pressure.
4. Feedback:Reactor Pressure trend.
Critical Tasks — Three
Within 10 minutes of recorded time in SSI an Operator has placed the following switches inTest/Inhibit, at Panel 2-9-3: ECCS SYS I HI DW PRESS Test/Inhibit, 2-HS-75-59 AND ECCSSYS II HI DW PRESS Test/Inhibit, 2-HS-75-60.
1. Safety Significance:Prevent CAS initiation due to actual high Drywell Pressure, and minimize the number ofsubsequent additional actions (to secure/realign both credited and non-credited pumps).
2. Cues:Procedural compliance.No AUTO initiation of ECCS when Drywell Pressure exceeds 2.45 psig.
3. Measured by:Observation - 2-HS-75-59 and 60 in Test/Inhibit.Observation - No AUTO initiation on high drywell pressure.
4. Feedback:ECCS Pumps green lights ON and Red Lights Off.
EVENTS
1. BOP Operator warms RFPT B lAW 2-01-3 Feedwater System, section 5.6 step 2.2.
2. ATC Continues Power ascension with control rods.
3. During power ascension Control Rod 34-3 5 will fail to withdraw. The crew will respondlAW 3-01-85. Once Drive water pressure is at 350 psig or greater the control rod will triplenotch to position 14 which is one notch beyond the banked position of 12.
4. The Unit Supervisor should enter 2-AOI-85-7 for a mispositioned control rod. All attemptsto insert the control rod to the correct position will fail. The control rod will be declared stuckand the SRO will enter Tech Specs and determine TS 3.1.3 condition A.
5. A loss of 480V Unit Board 2A will occur. EHC Pump 2A will trip due to loss of power andthe standby pump will not auto start, BOP operator will start EHC Pump 2B to prevent a lossof EHC pressure and closure of Turbine Bypass Valves.
6. Level transmitter 58D will fail to less than -45 inches. This failure will result in a RCICinadvertent initiation. The BOP Operator will respond lAW ARPs. BOP Operator will verifythat level is in normal band and secure RCIC. The SRO will evaluate Technical Specification3.5.3 Condition A, 3.3.4.2 Condition A, 3.3.5.1 Condition A, B and F, 3.3.5.2 Condition Aand B, and 3.8.1 Condition D.
7. The crew will respond to a fire and enter 0-AOI-26-1 and SSI 25-1, Intake Pumping StationPump El. 550, Cable Tunnel to Fire Door 440, RHRSW Room B, RURSW Pump Room D.The SRO will also enter EOI-1 and 2 and perform actions that do not conflict with the SSIguidance.
8. Shortly after entering the SSI the crew will commence a controlled cooldown lAW the SSIutilizing HPCI and SRVs, the HPCI flow controller will fail in Auto but will operate inmanual.
9. Numerous instruments fail due to the SSI Fire and spurious equipment operation occurswhich the crew will respond to lAW SSI 25-1.
Terminate the scenario when the following conditions are satisfied or upon request of LeadExaminer:
Reactor Level is maintained
Controlled Cooldown in progress
SCENARIO REVIEW CHECKLIST
SCENARIO NUMBER: 6
10 Total Malfunctions Inserted: List (4-8)
4 Malfunctions that occur after EOI entry: List (1-4)
4 Abnormal Events: List (1-3)
1 Major Transients: List (1-2)
2 EOI’s used: List (1-3)
0 EOI Contingencies used: List (0-3)
75 Validation Time (minutes)
3 Crew Critical Tasks: (2-5)
YES Technical Specifications Exercised (Yes/No)
\j} \\\\\Th
Scenario Tasks
TASK NUMBER EQ SEQ
Warm RFPT 2B lAW 2-01-3
RO U-003-N0-23 259001 A4.02 3.9 3.7
Raise Power with Control Rods
RO U-085-N0-07SRO S-000-AD-31 2.2.2 4.6 4.1
Control Rod difficult to withdraw from a position other than 00
ROU-085-N0-19 201001A4.04 3.1 3.1SRO S-000-AD-3 1
Control Rod Mispositioned
RO U-085-AB-07 201002 A2.02 3.2 3.3SRO S-085-AB-07
Loss of 480V Unit BD 2A
RO U-57B-AL-06 226001 A2.04 3.8 4.2SRO S-57B-N0-07
RCIC Inadvertent Start
RO U-071-N0-5 217000 A2.01 3.8 3.7SRO S-000-AD-27
SSI FIRE
RO U-000-EM-85 600000 AA2.16 3.0 3.5RO U-000-SS-30RO U-000-N0-32SRO S-000-EM-30SRO S-000-SS-30SRO S-000-SS-3 1
\\,\\
Appendix D Scenario Outline Form ES-fl-i
( ‘acility: Browns Ferry NPP Scenario No.: NRC —7 Op-Test No.:
Examiners:_____________________ Operators: SRO:______________________
________________
ATC:_______________
________________
BOP:________________
Initial Conditions: Reactor Power is 23%, Unit startup is in progress lAW 3-G0I-lO0-1A. EECW A3 andSteam Packing Exhauster 3A.
Turnover: Inert the Primary Containment in accordance with 3-01-76 starting at step 47. Commence apower increase with Control Rods to 30% in accordance with Reactivity Control Plan.
Event Maif. No. Event Type* Event DescriptionNo.
N-BOP1 Inert the Primary Containment in accordance with 3-01-76
N-SRO
R-ATC2 Power increase with Control Rods 30%
R-SRO
I-ATC3 rd25r5035 Failed RPIS position indication on rod 50-3 5 at position 36
I-SRO
C-ATC4 cuo 1 RWCU Leak with failure to Auto isolate
TS-SRO
dg03b C-BOPLoss of EECW C3 Pump through loss of 4KV SID Board 3EB
TS-SRO
C-BOP6 ms0 1 Loss of Condenser Vacuum
C-SRO
7 edO 1 M-ALL Loss of Offsite Power
8 dgola C DG 3EA Fails to Auto start
9 th2l M-All LOCA
10 hpO4 C HPCI Steam Supply Valve fails to auto open.
* (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor
Appendix D Scenario Outline Form ES-D-1
Critical Tasks - Five
With a primary system discharging into the secondary containment, take action to manually isolate the break.
1. Safety Significance:Isolating high energy sources can preclude failure of secondary containment and subsequent radiationrelease to the public.
2. Cues:Procedural compliance.Area temperature indication.
3. Measured by:With the reactor at pressure and a primary system discharging into the secondary containment, operatortakes action to manually isolate the break.
4. Feedback:Valve position indication
RPV Level maintained above -162 inches, HPCI has been manually initiated.
1. Safety Significance:Maintaining adequate core cooling
2. Cues:RPV level indication
3. Measured by:HPCI injecting at required flow rate
4. Feedback:RPV level trendHPCI injection valve open
Appendix D Scenario Outline Form ES-D-1
Critical Tasks — Five
With RPV pressure below the Shutoff Head of the available Low Pressure system(s), operate availableLow Pressure system(s) to maintain or restore RPV water level above T.A.F. (-162 inches).
1. Safety Significance:Maintaining adequate core cooling.
2. Cues:Procedural compliance.Pressure below low pressure ECCS system(s) shutoff head.
3. Measured by:Operator manually starts initiates available low pressure ECCS systems and injects into theRPV to maintain or restore water level above -162 inches.
4. Feedback:Reactor water level trend.Reactor pressure trend.
To prevent an uncontrolled RPV depressurization when Reactor level cannot be restored and maintainedabove -162 inches, inhibit ADS.
1. Safety Significance:Maintain adequate core cooling, prevent degradation of fission product barrier.
2. Cues:Procedural compliance.
3. Measured by:ADS logic inhibited prior to an automatic initiation.
4. Feedback:RPV pressure trend.RPV level trend.ADS “ADS LOGIC BUS A/B iNHIBITED” annunciator status.
\
Appendix D Scenario Outline Form ES-D-1
Critical Tasks — Five
When Suppression Chamber Pressure exceeds 12 psig, initiate Drywell Sprays while in the safe regionof the Drywell Spray Initiation Limit (DSIL) curve and prior to exceeding the PSP limit.
1. Safety Significance:Precludes failure of containment
2. Cues:Procedural complianceHigh Drywell Pressure and Suppression Chamber Pressure
3. Measured by:Observation - US directs Drywell Sprays lAW with EOI Appendix 1 7B
ANDObservation - RO initiates Drywell Sprays
4. Feedback:Drywell and Suppression Pressure loweringRHR flow to containment
OR
Before Drywell temperature rises to 280°F, initiate Drywell Sprays while in the safe region of theDrywell Spray Initiation Limit (DSIL) curve.
1. Safety Significance:Precludes failure of containment
2. Cues:Procedural complianceHigh Drywell Pressure and Suppression Chamber Pressure
3. Measured by:Observation - US directs Drywell Sprays JAW with EOI Appendix 17B
ANDObservation - RO initiates Drywell Sprays
4. Feedback:Drywell and Suppression Pressure loweringRHR flow to containment
Appendix D Scenario Outline Form ES-D-1
Events
1. BOP will continue with Inerting Primary Containment lAW 3-01-76
2. ATC will commence to raise power with control rods to 30%.
3. Failed RPIS position indication on rod 50-3 5 at position 36, crew will refer to 3-AOI-85-4.Inserting the rod one notch will restore position indication.
4. The crew will respond to RWCU alarms indicating a leak and RWCU valve 3-FCV-69-1will fail to automatically isolate. The ATC will isolate RWCU and take actions lAW3-A0I-64-2A. The SRO will enter E0I-3 on High Secondary Containment Temperatures,evaluate Tech Spec 3.6.1.3, and determine Condition A must be entered. Also, TRMTechnical Surveillance Requirement 3.4.1.1 to monitor Reactor Coolant Conductivitycontinuously cannot be met and samples must be drawn every 4 hours.
5. The crew will respond to a loss of 4KV Shutdown Board 3EB. This will result in a loss of therunning EECW pump C3. The operator will take action to start EECW pump Cl. The SRO willrefer to Tech Specs and initially determine TS 3.7.2 Condition A. Once the Cl EECW pump hasbeen aligned the SRO will determine TS 3.7.1 Condition A now applies.
6. Condenser Vacuum will begin to degrade the SRO will initially enter 3-AOI-47-3 and then whenthe main turbine is tripped the SRO will enter 3-AOI-47-1. Condenser Vacuum will continue todegrade.
7. Prior to the SRO directing a Reactor Scram on vacuum a Loss of Offsite Power will occur. Thecrew will respond to the Reactor Scram lAW 3-AOI-100-1 and 0-AOI-57-1A.
8. During the LOOP DG 3EA will fail to automatically start and will have to be manually started.
9. Sometime after the LOOP a LOCA will develop requiring the crew to utilize systems to maintainReactor Level and Containment parameters.
10. The HPCI Steam Supply Valve, 3-FCV-73-16, will fail to OPEN on an automatic HPCIinitiation signal.
Terminate the scenario when the following conditions are satisfied or upon request of Lead Examiner:
Drywell Sprays initiated
Reactor Level is maintained above TAF
\\1
Appendix D Scenario Outline Form ES-B-i
C SCENARIO NUMBER: 7
10 Total Malfunctions Inserted: List (4-8)
2 Malfunctions that occur after EOI entry: List (1-4)
4 Abnormal Events: List (1 -3)
2 Major Transients: List (1-2)
3 EOI’s used: List (1-3)
1 EOI Contingencies used: List (0-3)
75 Validation Time (minutes)
5 Crew Critical Tasks: (2-5)
0 YES Technical Specifications Exercised (Yes/No)
Appendix D Scenario Outline Form ES-D-1
Scenario Tasks
TASK NUMBER K/A RO SRO
Inert Primary Containment
RO U-076-NO-0l
Raise Power with Control Rods
223001 A4.03
RO U-085-NO-07SRO S-000-NO-3 1
RWCU Leak with Failure to Auto Isolate
223002 A3.02 3.5 3.5
Control Rod 50-35 Position failure
214000 A2.01 3.1 3.3
Loss of Condenser Vacuum
RO U-047-AB-03SRO S-047-AB-03
LOOP
295002 AA1.05
RO U.-57A-AB-01RO U-082-AL-07SRO S-57A-AB-01
LOCA
295003 AA1.03
RO U-000-EM-01RO U-000-EM-02RO U-000-EM-05RO U-000-EM-3 1RO U-000-EM-32RO U-000-EM-80SRO S-000-EM-0lSRO S-000-EM-02
295024 EA1.11295031 EA2.04
SRO S-000-EM-05
3.4 3.4
2.2.2
RO U-069-AL-10SRO S-000-EM-12
4.6 4.1
RO U-085-AL-14SRO S-085-AB-04
3.2 3.2
4.4 4.4
4.2 4.24.6 4.8