GRUNDFOS DATA BOOKLET

TPE 100-240/2-S-A-F-A-BAQE 3X400 50HZ Grundfos Pump 99114589

Thank you for your interest in our productsPlease contact us for more information, or visit our websitehttps://www.lenntech.com/grundfos/TPE0S2/99114589/TPE-100-240-2-S-A-F-A-BAQE.html

info@lenntech.comtel. +31-15-261.09.00fax. +31-15-261.62.89

BE > THINK > INNOVATE

Printed from Grundfos Product Centre [2018.02.043]

Position Qty. Description1 TPE 100-240/2-S A-F-A-BAQE

Product No.: 99114589

Single-stage, close-coupled, volute pump with in-line suction and discharge ports of identical diameter.The pump is of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can beremoved for maintenance or service while the pump housing remains in the pipework.The pump is fitted with an unbalanced rubber bellows seal. The shaft seal is according to EN 12756.Pipework connection is via PN 16 DIN flanges (EN 1092-2 and ISO 7005-2).The pump is fitted with a fan-cooled, permanent-magnet synchronous motor. The motor includes afrequency converter and PI controller in the motor terminal box. This enables continuously variablecontrol of the motor speed, which again enables adaptation of the performance to a given requirement.The pump is fitted with a differential-pressure sensor.

Further product detailsThe pump is suitable for applications requiring pressure or temperature control and offers followingcontrol modes:

- AUTOADAPT. This function continuously adjusts the proportional-pressure curve andautomatically sets a more efficient curve without compromising comfort demands.

- FLOWADAPT. This control mode combines AUTOADAPT with a flow-limitting function. Thepump continuously monitors the flow rate to ensure the desired maximum flow is not exceeded.This will save the cost of a separate pump-throttling valve.

- Constant differential pressure. The pump head is kept constant, independent of the flow in thesystem.

- Proportional pressure. The head of the pump will increase proportionally to the flow in thesystem to compensate for the large pressure losses in the distribution pipes.

- Constant temperature. The return-pipe temperature is kept constant. Note: If the pump is intalledin the flow pipe, an external temperature sensor must be installed in the return pipe of thesystem.

- Constant differential temperature. The differential temperature can be measured by adifferential-temperature sensor or two separate temperature sensors.

- Constant curve. The pump can be set to run at a constant speed in the range of 25 to 100 % ofthe maximum speed.

A control panel enables setting of required setpoint as well as setting of pump to "Min." or "Max."operation or to "Stop". The control panel has indicator lights for "Operation" and "Fault".

Communication with the pump is possible by means of the Grundfos GO Remote (accessory). Theremote control enables further settings as well as reading out of a number of parameters such as"Actual value", "Speed", "Power input" and total "Power consumption".

PumpPump housing and pump head are electrocoated to improve the corrosion resistance.Electrocoating includes:1) Alkaline-based cleaning.2) Pretreatment with zinc phosphate coating.3) Cathodic electrocoating (epoxy).4) Curing of paint film at 200-250 °C.

Printed from Grundfos Product Centre [2018.02.043]

1: Pump housing2: Impeller3: Stub shaft4: Pump head/motor stool5: Wear rings

The pump housing is provided with a replaceable bronze neck ring to reduce the amount of liquidrunning from the discharge side of the impeller to the suction side. The impeller is secured to the shaftwith a nut.

The pump is fitted with an unbalanced rubber bellows seal with torque transmission across the springand around the bellows. Due to the bellows, the seal does not wear the shaft, and the axial movementis not prevented by deposits on the shaft.Primary seal:

- Rotating seal ring material: Carbon graphite, metal-impregnated- Stationary seat material: Silicon carbide (SiC)

This material pairing has a very good corrosion resistance and is especially suitable for water up to+120 °C. However, seal life will be reduced at temperatures above +90 °C. The material pairing is notrecommended for liquids containing particles as this will result in heavy wear on the SiC face.Secondary seal material: EPDM (ethylene-propylene rubber)EPDM has excellent resistance to hot water. EPDM is not suitable for mineral oils.

A circulation of liquid through the duct of the air vent screw ensures lubrication and cooling of the shaftseal.The flanges have tappings for mounting of pressure gauges.

The motor stool forms connection between the pump housing and the motor, and is equipped with amanual air vent screw for venting of the pump housing and the shaft seal chamber. The sealingbetween motor stool and pump housing is an O-ring.The central part of the motor stool is provided with guards for protection against the shaft and coupling.The pump stub shaft is fastened directly on the motor shaft with key and set screws.

MotorThe motor is a totally enclosed, fan-cooled motor with principal dimensions to IEC and DIN standards.Electrical tolerances comply with IEC 60034.

The motor is flange-mounted with free-hole flange (FF).Motor mounting designation in accordance with IEC 60034-7: IM B 5, IM V 1 (Code I) / IM 3001, IM3011 (Code II).

The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2.The motor requires no external motor protection. The motor control unit incorporates protection againstslow- and quick-rising temperatures, e.g. constant overload and stalled conditions.

The terminal box holds terminals for these connections:- one dedicated digital input- two analog inputs, 0(4)-20 mA, 0-5 V, 0-10 V, 0.5 - 3.5 V; the factory-fitted pressure sensor is

connected to one of these inputs- 5 V voltage supply to potentiometer and sensor- one configurable digital input or open-collector output- Grundfos Digital Sensor input and output- 24 V voltage supply for sensors- two signal relay outputs (potential-free contacts)

Printed from Grundfos Product Centre [2018.02.043]

Position Qty. Description- GENIbus connection- interface for Grundfos CIM fieldbus module.

Technical data

Liquid:Pumped liquid: WaterLiquid temperature range: 0 .. 120 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³

Technical:Speed for pump data: 2910 rpmRated flow: 94.5 m³/hRated head: 20.3 mActual impeller diameter: 137 mmPrimary shaft seal: BAQECurve tolerance: ISO9906:2012 3B

Materials:Pump housing: Cast iron

EN-JL1040ASTM A48-40 B

Impeller: Cast ironEN-JL1030ASTM A48-30 B

Installation:Range of ambient temperature: -20 .. 50 °CMaximum operating pressure: 16 barFlange standard: DINPipe connection: DN 100Pressure rating: PN 16Port-to-port length: 500 mmFlange size for motor: FF265

Electrical data:Motor type: 132SFIE Efficiency class: IE5Rated power - P2: 7.5 kWMains frequency: 50 HzRated voltage: 3 x 380-500 VRated current: 14,1-11,2 ACos phi - power factor: 0,93-0,89Rated speed: 360-4000 rpmEfficiency: 92,5%Enclosure class (IEC 34-5): IP55Insulation class (IEC 85): F

Others:Minimum efficiency index, MEI ≥: 0.58ErP status: EuP Standalone/Prod.Net weight: 110 kgGross weight: 129 kgShipping volume: 1.12 m³

Printed from Grundfos Product Centre [2018.02.043]

99114589 TPE 100-240/2-S 50 HzH

[m]

0

5

10

15

20

25

30

Q [m³/h]0 10 20 30 40 50 60 70 80 90 100 110 120

eta[%]

0

20

40

60

80

100

TPE 100-240/2-S, 3*500 V

110 %

100 %

90 %

80 %

70 %

60 %

50 %

40 %

25 %20 %

P[kW]

0

2

4

6

8

NPSH[m]

0

5

10

15

20P1 (motor+freq.converter)

P2

Printed from Grundfos Product Centre [2018.02.043]

H[m]

0

5

10

15

20

25

30

Q [m³/h]0 20 40 60 80 100

eta[%]

0

20

40

60

80

100

TPE 100-240/2-S, 3*500 V

110 %

100 %

90 %

80 %

70 %

60 %

50 %

40 %

25 %20 %

P[kW]

0

2

4

6

8

NPSH[m]

0

5

10

15

20P1 (motor+freq.converter)

P2

250

100

254.9

M16

Rp 1/4

237 237

237

173173

245

140

0

774

124156 500

144

3

15

8

26

23

25

24

7

21

20

22

B

Y

6

5

2

4

10

A

+24 V*

1

149

12

17

19

11

18+24 V*

OC DI

+24 V*

AI2

GDS RX

GDS TX

GND

GENIbus A

GENIbus B

+24 V

GND

GENIbus Y

GND

DI1

AI1

DI3/OC1

LiqTec

AI3

GND

DI2

LiqTec

GND

AO

Pt100/1000

Pt100/1000

DI4/OC2

GND

+24 V*OC DIGND

NC

C2

NO

NC

C1

NO

+24 V*+24 V* +24 V*/5 V*

L2

L1

L3

PE

L3

L2

L1

+24 V* +24 V*/5 V*+24 V*

+24 V*/5 V*

+5 V*

+5 V

+24 V

+5 V

+5 V*

Description ValueGeneral information:

Product name: TPE 100-240/2-SA-F-A-BAQE

Product No: 99114589EAN number: 5712607032050Technical:Speed for pump data: 2910 rpmRated flow: 94.5 m³/hRated head: 20.3 mHead max: 240 dmActual impeller diameter: 137 mmPrimary shaft seal: BAQECurve tolerance: ISO9906:2012 3BPump version: AModel: AMaterials:Pump housing: Cast iron

EN-JL1040ASTM A48-40 B

Impeller: Cast ironEN-JL1030ASTM A48-30 B

Material code: AInstallation:Range of ambient temperature: -20 .. 50 °CMaximum operating pressure: 16 barFlange standard: DINConnect code: FPipe connection: DN 100Pressure rating: PN 16Port-to-port length: 500 mmFlange size for motor: FF265Liquid:Pumped liquid: WaterLiquid temperature range: 0 .. 120 °CLiquid temperature during operation: 20 °CDensity: 998.2 kg/m³Electrical data:Motor type: 132SFIE Efficiency class: IE5Rated power - P2: 7.5 kWMains frequency: 50 HzRated voltage: 3 x 380-500 VRated current: 14,1-11,2 ACos phi - power factor: 0,93-0,89Rated speed: 360-4000 rpmEfficiency: 92,5%Enclosure class (IEC 34-5): IP55Insulation class (IEC 85): FMotor protec: YESMotor No: 98971272Controls:Control panel: HMI300 - AdvancedFunction Module: FM300 - AdvancedOthers:Minimum efficiency index, MEI ≥: 0.58ErP status: EuP Standalone/Prod.Net weight: 110 kgGross weight: 129 kgShipping volume: 1.12 m³Config. file no: 99138649

250

100

254.9

M16

Rp 1/4

237237237

173173

124156500

Printed from Grundfos Product Centre [2018.02.043]

99114589 TPE 100-240/2-S 50 Hzcos phi

eta

0.0

0.2

0.4

0.6

0.8

P2 [kW]0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0

I[A]

0

4

8

12

16

TPE100-240/2-S + 132SF 7.5 kW 3*500 V, 50 Hz

eta

cos phi

I

n[rpm]

0

1000

2000

3000

4000

P1[kW]

0

2

4

6n

P1 (motor+freq.converter)

n = 109 %

Printed from Grundfos Product Centre [2018.02.043]

99114589 TPE 100-240/2-S 50 Hz

Note! All units are in [mm] unless others are stated.Disclaimer: This simplified dimensional drawing does not show all details.

250

100

254.9

M16

Rp 1/4

237 237

237

173173

245

140

0

774

124156 500

144

Printed from Grundfos Product Centre [2018.02.043]

99114589 TPE 100-240/2-S 50 Hz

Note! All units are in [mm] unless others are stated.

3

15

8

26

23

25

24

7

21

20

22

B

Y

6

5

2

4

10

A

+24 V*

1

14

9

12

17

19

11

18+24 V*

OC DI

+24 V*

AI2

GDS RX

GDS TX

GND

GENIbus A

GENIbus B

+24 V

GND

GENIbus Y

GND

DI1

AI1

DI3/OC1

LiqTec

AI3

GND

DI2

LiqTec

GND

AO

Pt100/1000

Pt100/1000

DI4/OC2

GND

+24 V*OC DIGND

NC

C2

NO

NC

C1

NO

+24 V*+24 V* +24 V*/5 V*

L2

L1

L3

PE

L3

L2

L1

+24 V* +24 V*/5 V*+24 V*

+24 V*/5 V*

+5 V*

+5 V

+24 V

+5 V

+5 V*

Disclaimer: The information about the Grundfos pump in this document may be outdated.Data may be subject to alterations without further notice.Please contact us to verify the data above is still accurate/up-to-date.

All information is copyright Grundfos.

info@lenntech.comwww.lenntech.comtel. +31-15-261.09.00fax. +31-15-261.62.89