ADL Uplink

User Guide

2

WelcomeCongratulations on your purchase of the ADL Uplink rebroadcaster, the simplest and most versatile way to extend the range of Internet-based RTK corrections. Use the ADL Uplink program to connect to the Internet via the internal cellular or Wi-Fi modems. Th en seamlessly stream RTK corrections to any Pacifi c Crest ADL or PDL radio for rebroadcast into poor coverage zones, built-up areas, valleys or anywhere cellular coverage is not 100% reliable.

NOTE: Not all the features discussed in this manual will apply to every unit, as some of the features are off ered as options. If the feature described does not apply to your unit, please disregard that section.

Limited Warranty & Liability LimitationsTh is product is limited warranted against defects in materials and workmanship for twelve (12) months from the original date of purchase. ADL Uplink accessories and peripherals are limited warranted against defects in materials and workmanship for ninety (90) days from the original date of purchase. If notice is received of such defects during the limited warranty period, the proven defective product(s) will either be repaired or replaced, at the manufacturer’s option. Replacement products may be either new or like new.

Th e manufacturer does not warrant that the operation of the products will be uninterrupted or error free. If the product is not, within a reasonable time, repaired or replaced to a condition as limited warranted, the customer will be entitled to a refund of the purchase price upon prompt return of the product.

Limited warranty does not apply to defects resulting from (a) improper or inadequate maintenance or calibration, (b) software, interfacing, parts, or supplies not supplied by manufacturer, (c) unauthorized modifi cation, or misuse, (d) operation outside of the published environmental specifi cations for the product, or (e) physical damage due to external causes, including accident, abuse, misuse or problems with electrical power. Water damage caused by improper installation of the Expansion Caps or I/O Boots is not covered by warranty. Removal of the back case voids the limited warranty. Th ere are important seals that will break and the ADL Uplink will no longer be waterproof.

To the extent allowed by local law, the above limited warranties are exclusive and no other warranty or condition, whether written or oral, is expressed or implied, specifi cally disclaiming any implied warranties or conditions of merchantability, satisfactory quality, and fi tness for a particular purpose.

To the extent allowed by local law, the remedies in this limited warranty statement are the customer’s sole and exclusive remedies. Except as indicated above, in no event will the manufacturer or its suppliers be liable for loss of data or for direct, special, incidental, consequential (including lost profi t or data), or other damage, whether based in contract, tort, or otherwise.

3

ContentsWelcome 2

Limited Warranty & Liability Limitations 2

Device Hardware 4

Unit Setup 5

Working with the Unit and the Battery 7

Status indicators 10

Settings on your Unit 10

Working with the Cellular Modem 11

Connecting to a PC 13

Working with Bluetooth 13

Working with Wi-Fi (802.11) 14

Working with ADL Uplink Software 15

Reconnecting to the RTK Server 21

Installing ADL Uplink program upgrades 21

Installing additional software on your unit 21

Working with the GPS 21

Using SatViewer 23

Troubleshooting 28

Caring for your Unit 29

Environmental Considerations 29

Environmental Specifi cations 30

Hardware Specifi cations 30

Regulatory Information 31

Declaration of Conformity 32

Safe Use of your Unit 32

4

Device Hardware

Front View Numeric Data Keypad

Expansion Cap

Backspace*

Enter*

Application Soft Key*

Notification LED

OK*

Today*

Number pad and Navigation keys For more information about the function key,

see page 17

Tab*

Power

Application Soft Key*

Start*

Function Key*

Battery LED

Back View with hand strap

BatteryDoor

HandStrap

Expansion Cap

lus

BatteryDoorScrews

I/O Boot

Bottom View

USB I/O Boot

Mini-USB

Client

USBHost

AudioJack

ExternalPower

Bottom View

Serial I/O Boot

SerialMini-USB

Client

ExternalPower

Cellular OptionExpansion Cap (GPS Antenna)

CellularAntenna

Top ViewStandard

Expansion Cap

SDslot

CF type IIor USB

An Extended Cap, sold as an accessory, can be used for oversized CompactFlash (CF) and Secure Digital (SD) cards.

NOTE: Be sure to read the warranty and safety information in this manual prior to using your unit.

5

Unit Setup1. Install the battery

Th e Lithium-Ion (Li-Ion) battery and battery cover are shipped detached from the unit. Insert the battery into the compartment so the connectors on the battery mate with the pins in the battery compartment. Press fi rmly. Place the battery door over the battery, with the fl at side of the battery door at the top.

Remove the rubber cap from the end of the stylus to expose a Philips screwdriver, or use a small #1 Philips head screwdriver to fi nger-tighten the four screws in the battery door.

NOTE: DO NOT use the screwdriver part of the stylus on the touchscreen or it will scratch your screen. Only use the spring-tip end of the stylus.

IMPORTANT: Fully charge the battery once it’s installed in the unit. Th e battery gauge may not be accurate until it has been fully charged at least one time, which should take approximately 4 ½ hours. Th e battery LED (right side of unit) will turn green once it’s fully charged.

2. Charge the battery

Th e AC adapter that ships with your unit has multi-national plugs that fi t almost every electrical outlet in the world. Connect the AC plug for your country to the AC adapter. Plug into an electrical outlet and plug the barrel end of the AC adapter into the unit.

Warning! Be sure to only use the AC adapter included with your unit. Use of other adapters may void the product warranty.

3. Attach the hand strap

Attach the hand strap to the back case, as shown.

4. Install the screen protector

To keep the touchscreen clean and protected, install the screen protector following the instructions provided in the screen protector package. Unprotected screens become scratched and scuff ed over time. Screen protectors extend the life of the display by providing a protective and replaceable barrier between abrasive grit and the surface of the display.

Screen damage associated with failure to use a screen protector may not be covered under warranty.

5. Turning your unit on and off

Th e unit should boot up when the battery is installed. If not, press and release the green Power key on the keypad. To turn your unit off , press and release the Power key again.

One of the most convenient features of your unit is “instant on” and “instant off ” (also known as “suspend/resume”). Th ere is no waiting for the unit to boot up every time it is turned on. “Instant on” does not occur on the fi rst boot-up.

When the unit fi rst turns on, the message “Tap the screen to set up your Windows Mobile-based device” will appear.

6. Align screen

Th e align screen message will display a series of targets to tap in sequence on the screen. Use the stylus to tap the targets fi rmly and accurately. Sometimes you need to repeat the alignment procedure more than once to provide a satisfactory alignment.

7. Location – time zone

Select your time zone location, set the time and date to the correct values and tap Next.

8. Password – lock (optional)

You do not have to provide a password unless you are concerned about unauthorized use. To eliminate using a password, tap Skip.

If you opt for password protection the password must be entered every time the unit is turned on or the Power key is pressed to resume operation.

WARNING: BE CERTAIN TO REMEMBER THE PASSWORD. Th e only way to recover from a forgotten password is to perform a Clean Boot and you will LOSE all application software, licenses, settings and data on your unit. See page 15 on how to perform a Clean Boot.

6

9. Using the expansion ports

To access the expansion ports, use the Philips screwdriver end of the stylus or a small #1 Philips head screwdriver to rotate the two quarter-turn fasteners counter-clockwise and remove the Expansion Cap.

Under the Expansion Cap is a Secure Digital (SD) expansion slot. Depending upon the confi guration of your unit, it may contain a CompactFlash (CF) type II slot, USB port, a camera and/or a scanner. Th e scanner and camera units have a clear window in the cap.

Gently insert cards into the slot and release; the card should catch in the slot. Make sure the front of the card faces the display side of the unit. Push the cards in straight, never at an angle or forced.

To eject an SD card, gently press the top of the card to release it. To eject a CF card, press the eject button next to the CF card.

NOTE: DO NOT use the unit without reattaching the cap and the boot. Th e unit is NOT sealed when the cap or boot is off and water damage can occur, possibly voiding the warranty.

10. Th e Today Screen

Th e Today screen provides information that you need for the day. Tap an item to view or edit details. To customize which items are shown on the Today screen, tap Start / Settings / Today / Items.

SD slot CF slottype II

Tap to change owner information

Tap to change time settings Tap to change WLAN &

Bluetooth settings Assisted GPS improves the time of locating satellites.

Tap to set up many useful features

Tap to view power settingsTap to change or mute volume

Tap to view and change connection settingsTap to go toa program

11. Getting Started

Th e Getting Started menu on the Today screen has a number of helpful features in setting up your unit. Th e Getting Started icon can be removed from the Today screen, if desired.

12. I/O Boots

Th ere are two types of boots available. Th e boots can be swapped by loosening the screws pointed out in the picture below.

Both boots have a mini-USB client that uses a standard USB cable (included with the unit). Th e mini-USB port can be used to connect to a personal computer (PC).

USB I/O Boot: Th is boot has a mini-USB client, a USB host port (to connect to USB client devices) and an audio jack that is wired for a headset with a mono speaker and microphone combination.

(It is not for stereo headsets.)

USB I/O Boot Serial I/O BootScrews to swap boot Screws to swap boot

Mini-USB

Client

USBHost

AudioJack

ExternalPower

Mini-USB

Client

ExternalPowerSerial

Pin 1Pin 6 Pin 9

Pin 5

7

NOTE: Many USB host peripheral devices supported on personal computers are not supported by this unit. Th ere are two classes of USB devices that have native support in the OS:

1. USB Human Interface Devices (HID). Examples include keyboards and some barcode scanners.

2. USB Mass-Storage devices. Examples include memory sticks, hard disks, some digital cameras and memory card readers.

Before purchasing a USB peripheral, check with the manufacturer to ensure that it will operate with one of these natively supported USB classes. Some devices have no applicability in Windows Mobile. For example, mice do not make sense to use with your unit because it is designed to be touchscreen or keypad operated.

Serial I/O Boot: Th is boot has a mini-USB client and an RS-232 connector for use with serial devices.

NOTE: COM1 is always reserved in software for the 9-pin port, even if you don’t have a unit with a serial boot.

Working with the Unit and the BatteryBattery life: Th e Lithium-Ion (Li-Ion) battery life is dependent upon the application and operating environment.

Tips for extending the battery life• Keypad backlight: Th e default is OFF. Using this backlight could reduce your battery life by up to 25%. For information on changing the backlight settings, see page 18.

• Display backlight: Tap Start / Settings / System / Backlight to minimize the amount of time the backlight stays on and dim it to only as bright as required to view the display.

• Wi-Fi, camera, or barcode scanner: If your unit comes with any of these options installed, use ONLY when necessary. Turn off when not needed. Minimize the Flash intensity and the use of the fl ashlight.

• Cold temperatures: Keep the unit as warm as possible. If feasible, keep it inside your coat or a vehicle when not in use.

• GPS: Ensure that the GPS-aware applications that communicate with the GPS are closed when not in use. Th e Today screen indicates if the GPS is running.

• Expansion ports: Select low-power consumption CF and SD cards and use them only when necessary.

• Auto features: Tap Start / Settings / System / Power / Advanced. To conserve battery power, specify your unit to turn off in a short time if not in use.

Other factors that may have some impact on battery life include heavy usage of the Bluetooth radio and heavy processing by the CPU, but these factors are typically less signifi cant.

Charging the batteryTh e battery can be charged in the unit or apart from the unit with an external battery charger (sold separately, as an accessory). Connect the AC plug for your country to the AC adapter. Plug into an electrical outlet and plug the barrel end of the AC adapter into the unit. Th e unit will be charged in about 4.5 hours.

A full charge is indicated by the battery LED (right side of the unit) turning green. Th e recommended temperature range for charging is between +32 °F and +113 °F (0 °C and +45 °C). If the battery temperature is outside of this range, the battery will not charge.

Warning! Be sure to only use the AC adapter included with your unit. Use of other adapters may void the product warranty.

8

Changing the battery Th e battery is designed to be quickly changed. Th e unit saves enough power that if you swap the battery within approximately one minute, it will not trigger a reset. If the saved power runs out before the new battery is installed, the unit will reset. Th is will not impact saved data, programs or confi guration, however unsaved data will be lost and the time settings will need to be reset.

To change a battery, perform the following steps:

1. Close open applications and save data in case the battery exchange takes too long.

2. Remove the hand strap from the unit.

3. Enter the Replace Battery mode (ensures that alarms will not wake up the unit while changing the battery). Press and hold the Power key and tap Replace Battery. See page 14.

4. Use the supplied stylus or a small #1 Philips head screwdriver to loosen the four screws in the battery door.

5. Remove the battery from the unit.

6. Quickly insert the replacement battery onto the unit.

7. Place the battery door over the battery, with the fl at side of the battery door at the top of the unit. Use the stylus or screwdriver to fi nger-tighten the four screws.

8. Replace the hand strap.

9. Turn on the unit to resume operation.

Calibrating the batteryTh e battery has an internal gauge that provides an estimate of the amount of energy in the battery as it charges and discharges. If your battery is showing inaccuracy in the power gauge or large jumps in capacity, (i.e. the power is reading 50% and goes dead shortly thereafter) it may need calibration.

Tap Start / Settings / System / Power / Calibration to see if the message reads Calibration recommended or Calibration not necessary. If calibration is recommended or the battery is reporting inaccurately, perform the following:

1. Plug in the AC adapter. Th e unit MUST stay plugged in during the calibration or you may need to restart the process.

2. Ensure the temperature is between +32 °F and +113 °F (0 °C and +45 °C) while charging.

3. Tap Start Calibration.

4. During the calibration process, the Power key is disabled temporarily and the backlight is turned up to 100%.

It takes up to 25 hours to complete the calibration. When fi nished, a notifi cation will state Calibration is complete. It is recommended to not use your unit during the calibration process. To stop the calibration process, tap Start / Settings / System / Power / Calibration / Stop Calibration.

Possible error messages that can occur during calibration:

Error Message Solution

Battery is not charging, aborting Battery temperature may be out of range. Wait until battery temperature settles and try again.

Discharge became invalid, restarting Calibration will restart itself.

AC power is in an unknown or uncontrolled state; aborting

Plug in unit and restart calibration. Try a diff erent AC adapter and restart calibration. If it continues to fail, have the unit serviced.

Notifi cation LEDsAt the top of the ADL Uplink are two LEDs that provide status information. Th e LED states are shown in the following tables.

Right LED Function

Off On battery power

Solid yellow Charging on AC adapter

Solid green Fully charged on AC adapter

Blinking yellow Battery problem during charging (temperature out of range, defective or missing battery)

9

Left LED Function

Off No notifi cations & phone off

Blinking yellow Microsoft notifi cations

Blinking green – short blink Phone on - network available

Blinking green – long blink Phone on - data transfer in progress

NOTE: If the left LED is blinking green, battery power is being consumed due to the cellular modem being turned on, even when the device is suspended.

Speaker and microphoneYour unit comes with an integrated speaker and a microphone. It also has an audio jack that is wired for a headset with a mono speaker and microphone combination. It is not for stereo headsets.

To record, tap Start / Programs / Notes. If you do not see the Recording toolbar, tap Menu / View Recording Toolbar. Tap the round record symbol on the screen. Th e unit will record until Stop is pressed. Th e recorded fi le will be saved in the Notes folder.

Power key featuresTh e Power key turns the unit on and off and performs a number of additional functions.

Turn backlight on/off : To toggle the backlight on or off , hold down the Power key for approximately 1 second. Once toggled off , the backlight will stay off until it is toggled back on. Screen taps and key presses will not cause it to turn on.

Power menu: Hold down the Power key for about 3 seconds to display a countdown. Continuing to press the Power key will cause a reset when the countdown reaches zero. If you release the Power key while the countdown is proceeding, you access the following menu. Tap an option or OK to exit.

Clean Screen: Disables the touchscreen for cleaning. Press the enter key to re-enable the touchscreen.

Align Screen: Repeats the alignment procedure.

Replace Battery/SIM: Ensures that alarms will not wake up the unit while changing the battery or the SIM.

Shutdown: Intended for long term storage to put the unit in its lowest power mode. Running application state, unsaved data, and real-time clock settings will be lost. Internal GPS parameters will be reset to their default settings. To take the unit out of the shutdown mode, press the power key and the unit will boot up.

NOTE: While in shutdown mode, the battery LED does not work, but if the AC adapter is plugged in, it will still charge.

Reset: Stops all running programs and restarts the unit. No fi le system data is lost, only open or unsaved fi les will be lost. All registry settings, control panel, personal information, GPS settings and databases are preserved.

NOTE: if the countdown or the Power menu does not appear when the power button is held down, continue to hold down the power button for at least 20 seconds to reset it.

Perform a Clean Boot WARNING: All application software installed by the factory and the customer, plus licenses, settings and user data will be cleared if this function is performed!

Hold down the Power key and press the right soft key to display a countdown. Continue to hold down both keys until it counts down to zero, followed by a brief appearance of the boot screen. Continue to hold both keys down until a screen appears warning that if you continue, this operation will clear the persistent store. Follow the instructions on the screen ONLY if you want to completely clear your unit.

NOTE: ScanAgent, SatViewer and CellStart ( found on the documentation CD) and any other applications installed will need to be reinstalled using ActiveSync. Certain confi guration parameters of the internal GPS receiver (baud, parity, etc.) will remain unchanged.

Storage memoryUnlike many handhelds which can lose data if they lose power, all your data is always stored in non-volatile persistent storage memory. Losing power will not impact saved data or confi gurations other than the real-time clock. Th is means that you do not have to use a RAM backup utility to protect your data. However, you can lose data by accidentally deleting or overwriting it. As with any computer system, we recommend that you regularly backup your data to removable media or to a PC.

Accessing storage memory using File ExplorerFile Explorer (Start / Programs / File Explorer) lets you browse the contents of folders on your unit. To easily delete, rename, or copy an item, touch and hold the item.

NOTE: Unlike PC’s, Windows Mobile does not support a Recycle Bin. Once a fi le is deleted, it cannot be recovered.

10

Status indicators Following are some of the status indicators seen on your unit.

Icon Description Icon Description

Battery power is low

Indicates that one or more networks are present. Tap to access an available network

Battery power is very low

Wireless LAN connected

Battery communication error

Active connection, but not currently synchronizing

Battery charging

Inactive connection to computer or wireless network

Battery level

Synchronizing

Battery calibration in progress

Synchronizing error

Instant messages received

E-mail has been received

Speaker is on

Pending alarm

Speaker is off (or in mute position)

Phone is turned on and signal strength

SIM card missing

Phone is turned off. To turn it on, tap this icon

Faulty SIM card

No signal

New voice mail

No service. Phone connection unavailable or network error.

Tap to view more notifications

Lost signal. The unit is searching for a signal.

Data call is in progress

EDGE available

New Instant message received

EDGE connected

Roaming mode GPRS available

GPRS connected

Settings on your Unit Tap Start / Settings. Tap any of the icons on the Personal, System or Connections tabs to customize the unit settings to your own preferences. Tap OK to exit the settings. Some of the more useful settings are described below.

Lock (password)If you want password protection from unauthorized use of your unit, tap Personal / Lock. Th e password must be entered every time you turn the unit on or resume operation.

WARNING: BE CERTAIN TO REMEMBER THE PASSWORD. Th e only way to recover from a forgotten password is to perform a Clean Boot. However, you will LOSE all application software, licenses, settings and data on your unit. For instructions on how to perform a Clean Boot, see page 15.

Buttons (keys)Tap Personal / Buttons. You can assign your favorite programs to several of the keypad buttons. Th e list of assignable keys is shown on the left hand side with the program that is assigned by default on the right. To reassign a key, select the key you wish to change in section 1 and choose the

desired program or action from the pull-down list in section 2. By default, the key will take you to the Camera application and the Camera Focus. Th e left soft key is assigned to the Flashlight, if the camera is present and the right soft key is assigned to the laser scanner, if present.

On the numeric data keypads, the yellow function key (sticky FN) accesses the tasks in yellow, including the Navigation arrows. Several settings can be changed under Keyboard Options.

Auto release: Press and release the function key to access a yellow task for one use. It then goes back to the keytop tasks.

Manual release: Th is is the default. Press the function key to toggle it on and off . Yellow tasks remains active until the function key is pressed again to input the keytop tasks.

Disabled: Th e function key has to be held down while pressing any other key to access the yellow task.

Play Sticky Key Sounds: To disable sticky key sounds, remove the check in the box.

11

Backlight for display and keypadTap System / Backlight. Change the settings as follows:

Display backlight: Th e default is on. Tap Battery Power, External Power and Brightness tabs to change settings.

Keypad backlight: Make changes by tapping the Keypad Battery, Keypad External or Keypad Brightness tabs.

PowerTap System / Power to view the approximate battery power remaining. Tap the Advanced tab and choose the settings for automatically turning off the unit when not in use.

Tap System / Power / Calibration to see if calibration is recommended. For more information on calibration, refer to page 12.

MemoryTap System / Memory to see how much Storage memory (Flash) and Program memory (RAM) is available. If there are external cards installed, tap Storage Card to view the available memory on the card. If there is more than one card installed, tap the dropdown arrow to select the diff erent cards.

Flash SettingsTap System / Flash Settings. Th e Flashlight turns on automatically. You can change the intensity of the Flashlight and the intensity of the Flash used for the camera. To turn the Flashlight on and off , push the left soft key.

Task ManagerClosing programs still leaves them resident in RAM. Windows Mobile will close background programs to free up RAM if resources are low. To manually close programs, tap Start / Programs / Task Manager. Tap on the program and tap End Task or tap Menu / End all Tasks.

System informationTap System / System Information. Firmware version, serial number, processor speed, RAM and Flash size, wireless confi gurations, battery and card port information can be found here.

Working with the Cellular ModemAfter purchasing a data connection plan from your local GSM cellular provider, you can link the ADL Uplink to the Internet to download and rebroadcast RTK corrections or to communicate from fi eld to offi ce via e-mail and text messages.

NOTE: When browsing the Internet using the cellular connection, you must turn off the Wi-Fi (802.11) or the ADL Uplink will default to the Wi-Fi to browse.

CAUTION:

• DO NOT use your ADL Uplink while driving a moving vehicle.

• DO NOT remove the cellular antenna unless directed by support personnel.

• When you are on a plane, in a medical facility or at a gas station where wireless communication devices are not allowed, go to Wireless Manager to TURN OFF all wireless communications. Simply turning the Power key off does not turn off these communications.

Installing (or changing) the SIM card1. Hold down the Power key for about 3 seconds and release to display the power menu. Tap Replace Battery/SIM to ensure the alarms will not wake up the ADL Uplink.

2. Remove the hand strap.

3. Use a small #1 Philips head screwdriver or the screwdriver on the end of your stylus to loosen the 4 screws in the battery door.

4. Remove the battery from the unit.

5. Slide the silver SIM carriage to the unlocked position (to the right).

6. Gently open the hinged SIM carriage door, and place the SIM card (purchased from your cellular service provider) into the slot. Th e golden contacts should be facing down. Also ensure that the notched corner aligns with the angled corner on the SIM carriage.

7. Close the SIM carriage and then slide it to the locked position (to the left).

8. Place the battery into the unit.

9. Place the battery door over the battery, with the fl at side of the battery door at the top of the unit. Use the screwdriver end of the stylus or screwdriver to gently tighten the four screws.

10. Replace the hand strap.

Setting up the cellular data connection1. Tap Start / Programs / CellStart. Under Available Data Settings, tap the [+] by your country to expand carriers.

12

2. Tap the [+] by the carrier you have signed up with and select Typical and tap Add Settings.

3. Ensure the phone is turned on and test the settings by opening Internet Explorer and browsing to a web page.

4. Try other settings before calling the carrier technical support.

NOTE: If you use multiple confi guration settings, you can select the primary by tapping the setting and tapping Default.

Removing cellular data settings1. Tap Start / Programs / CellStart.

2. Tap Refresh to see the current list of confi gurations.

3. Select the confi gured data setting you wish to remove.

4. Tap Remove and OK.

NOTE: After removing a default confi guration, the top setting will become the new default.

To access the detailed settings for each confi guration, tap Menu / Open Connections Applet for the Connections Settings.

Customizing your phoneTap Start / Settings / Phone.

Phone Number: The ring for text messaging notifications can be changed. Tap Start / Settings / Sounds & Notifications / Notifications and select Messaging: New text message. Choose the sound you want. PIN Number: a PIN can be set to block unauthorized access to your data connection. NOTE: This device is data-only and dialing controls are not available. Under Services, voice calls to the ADL Uplink can be forwarded to another phone.

Starting a cellular data connectionTap Wireless Manager on the Today screen to turn on the phone. It will automatically establish a cellular connection when needed.

If you want to start the connection manually, tap Start / Settings / Connections tab / Connections. Tap Manage existing connections. Tap and hold on the newly created connection name and tap Connect.

NOTE: EDGE is a faster form of GPRS. E or G will automatically appear in the notifi cation bar and will depend on the network capabilities in that area. Some service providers may only provide GPRS.

Using the cellular featuresNOTE: Th e cellular features of this ADL Uplink are used only for data communication and do NOT have voice capability or the ability to send MMS messages (Multimedia Messaging Service). Voicemails left on this number can be retrieved only by using another phone, depending upon the plan you purchased from your service provider. It is recommended to request the data-only plan from your service provider and have a “voice restriction” placed on your line.

Use the Wireless Manager to turn on the phone and wait at least 30 seconds before using the phone. Th e ADL Uplink may say the phone is on, but it needs to register with your service provider before it works properly. To save battery power, turn off the phone feature when not in use.

Browsing the InternetTap Start / Internet Explorer, and enter the address of one of your favorite web sites.

Internet SharingTh e Internet service from your ADL Uplink can be shared with a computer. Tap Start / Programs / Internet Sharing. You can connect either through USB or Bluetooth.

IMEI: Unique number that identifies the phone module that is embedded in the ADL Uplink. IMSI and ICCID: Unique numbers embedded on the SIM card. NOTE: If you purchase a SIM card separately, the phone service provider may want your ADL Uplink IMEI number. It is located on this screen, as well as in the battery compartment. NOTE: Under Band settings, leave settings set to Auto Band Select unless there is a good reason to make these adjustments manually.

13

SMS messagesYou can send a SMS (short message service) in exactly the same way as a normal mobile telephone. Each SMS text message can contain a maximum of 160 characters or less, depending on your service provider.

Sending and receiving e-mailE-mail setup: Tap Start / Messaging / Setup E-mail. Follow instructions to set up the e-mail service. You can synchronize with a POP Mail server, or with a Microsoft Exchange server.

Sending and receiving messages: Tap Start / Messaging and select an e-mail account. Tap New to compose a message and tap Send. Input the contact information. Depending on your account settings, your unit will check for new e-mail periodically. You can force a download of new messages, by tapping Menu / Send/Receive.

Connecting to a PCConnecting your unit to a PC allows you to copy fi les, synchronize information, send and receive e-mail and install applications on your unit. Connectivity software is pre-installed on your handheld unit.

Windows XP SP3 or earlier: Microsoft ActiveSync 4.5 or greater is required. (Microsoft Offi ce Outlook 2000 and older is not supported by ActiveSync 4.5.) NOTE: If you have an earlier version of ActiveSync installed on your PC, you need to upgrade to version 4.5 prior to connecting to your unit. Go to www.microsoft.com and search for ActiveSync.

Windows Vista & Windows 7: Microsoft Windows Mobile Device Center may be pre-installed on your PC. If it is not on your PC, go to www.microsoft.com and search for Windows Mobile Device Center to install it. NOTE: It does not recognize the serial port. You must connect by either USB or Bluetooth.

IMPORTANT: Do not connect your unit to the USB port on the PC until after you install connectivity software to your PC. If you prematurely connect the unit to your PC, your PC USB drivers may get into a confused state and will not connect. If you suspect that something like this has happened, uninstall the connectivity software on your PC, reboot, and reinstall.

After the connectivity software is installed on the PC, connect the unit to the PC:

1. Connect the USB end of the synchronization cable to the PC.

2. Turn on your unit.

3. Connect the mini-USB end of the cable to your unit.

Troubleshooting connection problems1. Confi rm the unit is confi gured to communicate with the PC. Tap Start / Programs / ActiveSync / Menu / Connections. Confi rm the box Synchronize all PC’s using this connection is checked and USB is selected from the dropdown list.

2. Try disabling any personal fi rewall software running on the PC. TCP/IP ports need to be open.

3. Reset the unit.

4. If you have more than one unit, PC and/or cable, testing diff erent combinations of equipment can help isolate the cause of the problem.

5. If you suspect the unit may have been connected to the PC USB port before the connectivity software was installed, then uninstall, reboot the PC, and reinstall.

6. Confi rm the version of connectivity software used on your PC (Microsoft ActiveSync 4.5 or greater for Windows XP or Windows Mobile Device Center for Windows 7 and Vista).

7. Tap Start / Settings / Connections / USB to PC and change the check box Enable advanced network functionality.

Working with BluetoothAll units come with embedded Bluetooth capability—a short-range wireless communication technology. Devices with Bluetooth capabilities can exchange information (beam) over a distance of up to 30 feet (10 meters), without requiring a physical connection.

Bluetooth settings: tap Start / Settings / Connections / Bluetooth.

Mode: To enable Bluetooth, select the check box Turn on Bluetooth. If you want other Bluetooth devices to fi nd your unit, also select the check box Make this device visible to other devices.

Devices: Tap Add new device to search for other Bluetooth devices. For enhanced security, use passcodes.

COM Ports: Available only for Bluetooth-connected devices that support serial (COM) connections.

Power: Maintain Bluetooth connections when device is turned off . When this check box is selected, Bluetooth connections on your unit are not terminated when your unit is turned off (suspended). When the unit is turned back on, the Bluetooth connections are intact, provided the other Bluetooth device is still connected. (Th e other device may not have this feature and may disconnect.)

NOTE: Communication cannot occur with other Bluetooth devices while your unit is suspended.

Power: Allow Bluetooth activity to turn the device on. When this check box is selected, another Bluetooth device can send data and your unit will turn on and reply if necessary.

NOTE: It is recommended that your unit be confi gured to automatically turn off when not in use. (See the Power section on page 14.) Otherwise, another Bluetooth device could turn on your unit, transfer data and if it does not turn off again, drain the battery.

14

Creating a Bluetooth Partnership: Bluetooth partnerships are required for connections to some PC’s, printers, and headphones. Confi guring Bluetooth connections vary depending upon how each Bluetooth device works. Refer to all device documentation.

1. Tap Start / Settings / Connections / Bluetooth / Mode. Ensure that both devices have Bluetooth turned on in the Mode area, are visible and within close range.

2. Tap Devices / Add new device… Wait a few moments while your unit searches for Bluetooth devices.

3. Tap the name of the other Bluetooth device and tap Next. For enhanced security, use passcodes. Enter the same passcode on the other unit.

4. If desired, change the name of the other device and tap Finish.

Once a partnership has been created, the devices do not need to be confi gured as visible any more.

Bluetooth connection with a PC1. Ensure that your PC has connectivity software installed. See Connecting to a PC on page 18.

2. Set up a partnership between your unit and the PC. Refer to your PC documentation for instructions.

3. After a few moments, select the PC from the Device list.

4. Confi rm that ActiveSync service is available and place a check in the check box and tap Finish.

5. Tap Start / Programs / ActiveSync / Menu / Connect via Bluetooth.

Bluetooth connection with a printer: If the printer is Bluetooth-enabled via Bluetooth serial profi le, it is possible to establish a Bluetooth connection.

1. Set up a partnership between your unit and the printer. (If the printer asks to connect to your unit, tap No.) Refer to your printer documentation for instructions and to see if a passcode is required.

2. After a few moments, select the printer from the Device list.

3. Confi rm that serial port service is available and place a check in the check box and tap Finish.

NOTE: Windows Mobile operating system does not support printing without additional third-party software.

Bluetooth-enabled headphone: You can use a Bluetooth stereo A2DP headphone only. Bluetooth handsfree audio devices that are typically used with cell phones are not supported.

Troubleshooting Bluetooth connection problems: If your unit cannot fi nd another Bluetooth device, confi rm that the device is within range (less than 30 feet / 10 meters) and no large objects obstruct the path of other Bluetooth-enabled devices. Confi rm that the device is turned on and has been confi gured to be discoverable.

Working with Wi-Fi (802.11)Using the ADL Uplink’s built-in Wi-Fi (also called Wireless LAN (WLAN) or 802.11) capability, you can wirelessly transmit data to and from your unit by connecting to available access points or hot spots. To fi nd out if you have Wi-Fi installed in your unit, tap Start / Settings / System / System Information / Wireless.

Th e Wi-Fi is off by default; however the on/off state will persist after a reset. To turn the Wi-Fi on or off , tap Wi-Fi from the Today screen or tap Start / Settings / Connections / Wireless Manager and tap Wi-Fi. Turn it off when not in use to save battery power and possibly speed up other processes.

To confi gure Wi-Fi, tap Tap here for Wi-Fi confi guration on the Today Screen.

1. Wi-Fi by default is disabled. Tap Options / Enable Wi-Fi.

2. Tap Scan for Networks to see the available networks.

3. Tap the network you want to connect to. Th e networks with three or four bars provide a better connection. Tap Next.

4. Tap Finish to begin using an open network. If the network does not require passwords, no changes are required.

5. If the network requires authentication, a Network Authentication dialog will open. For networks that require network keys, enter the network key into the dialog box and tap Finish to begin using the network.

6. For advanced networks tap the Authentication and Data Encryption required for this network. Additional keys or certifi cates may be required.

Status: Shows the details of your current connection.

Tools: Test connectivity by entering in a known good URL and tap Start Ping. You can also manage confi guration fi les here.

Advanced: You can set specifi c Wi-Fi settings required by some networks. Administrators can also set a password to limit access to confi guration settings.

To confi gure many ADL Uplinks identically, use the following steps:

Saving the Wi-Fi confi g fi le:

1. Confi gure an ADL Uplink as desired and save the confi guration under Start / Settings / Connections / Wi-Fi Settings / Tools / Store Confi guration to File. Th e default save location is My Documents.

2. Create a folder called TRAUTOWLAN on an external storage device (SD card, CF card, or USB drive). Th is folder must be in the root directory of the storage device.

15

3. Copy the saved confi guration fi le to the TRAUTOWLAN directory.

Loading the saved Wi-Fi confi g fi le:

1. First ensure the Wi-Fi Confi g is closed on the ADL Uplink that you are loading the new confi g by tapping Options / Close.

2. Insert the external storage device into the ADL Uplink.

3. Tap Start / Settings / Connections / Wi-Fi Settings. A dialog will appear, asking if you would like to apply the confi g. Tap Yes.

NOTE: Th e admin password must be entered if one is set.

Exchange ActiveSync: Exchange ActiveSync, a component of Exchange Server, facilitates data synchronization between your unit and an Exchange server. Th is synchronization can occur over a network connection, allowing you to update calendars, contacts, tasks and the Inbox on your unit without directly connecting to a PC. Th e server must be running Exchange Server 2003 SP2 or later.

To use Exchange ActiveSync, confi rm with your system administrator that an Exchange Server is available. Th e administrator will provide you with a login name, password, server name, and domain name. To confi gure Exchange ActiveSync on your unit, tap Start / Programs / ActiveSync / Menu / Add Server Source. Enter the server address and confi rm with your administrator whether the Exchange server requires an encrypted (SSL) connection. Tap Next. Enter the user name, password and domain and tap Next. Choose the data types you want to synchronize and tap Finish.

Troubleshooting Wi-Fi connection problems: If the unit seems to be connected to the network, but you are having diffi culty using the network connection, tap Start / Settings / Connections / Wi-Fi Settings / Networks, highlight the connection being used and tap Options / Edit and confi rm that the connection is appropriately confi gured as either a Work or Internet connection.

Working with ADL Uplink SoftwareOnce you have either the cellular or the Wi-Fi modem activated on your unit, you are ready to run the ADL Uplink software program.

Downloading the ADL Uplink Software LicenseTh e license to run the program was created and placed on an Internet server when Pacifi c Crest received your order. To download this license, turn on the unit and either tap

Start>ADL Uplink:

Or Start>Programs>ADL Uplink:

16

On the next screen tap the Retrieve License button:

If the ADL Uplink is within cell or Wi-Fi range, it will automatically connect to the Internet, download your software license and display the…

Main ScreenTh e main screen of the ADL Uplink program includes status indicators for the cellular modem, battery, GPS receiver and the UHF rebroadcaster.

Radio status

GPS staus

Cellularsignal level

BatteryStatus

Th ere are two buttons for the RTK Repeater (described below) and Setup. Th ere also is an exit button. Th e fi rst time you run the ADL Uplink program you will need to setup the unit, so tap the Setup button to display the ...

Setup ScreenTh e setup screen contains three buttons for setting up the ADL Uplink modem, its Internet link and its radio link. Th ere is also a button in the lower left that returns you to the previous screen (in this case, the main program screen).

Tap the Modem button to display the…

17

Modem Setup ScreenYou can select from any number of modem connection confi gurations using the Modem Setup Screen by tapping the down arrow next to the Connection fi eld.

If you have not setup any cellular connections yet, tap the New button to display the …

Add new connection screen

Tap the Country more arrow to display a list of countries. Tap a country to display the…

Operator Screen

Tap the Operator down arrow to display a list of operators (service providers) in the specifi ed country. Select one and tap the OK button to return to the Setup screen again.

If your country or operator is not displayed on this screen, you may confi gure the ADL Uplink software for connecting to a custom

18

operator. To do this, tap Custom on the Country fi eld, then tap the Name, User, APN and Password fi elds and enter the proper information – given to you by your operator – using the soft keypad that appears when you tap any data input fi eld.

When you are done with the custom confi guration, tap the back-arrow to return to the main Setup screen.

Internet Setup ScreenTapping the Internet button on the main Setup screen lets you confi gure the ADL Uplink rebroadcaster to access Internet servers providing RTK corrections.

19

Tap the Add (or Edit) button to display …

Add/Edit Server Screen

You can give the server any name you want, but the Network RTK service provider needs to give you your user name, password, the server’s IP address and perhaps a port number. To enter this information, tap any fi eld to display the soft keypad. When all applicable fi elds are fi lled out, tap the OK button to return to the main Setup screen.

Radio Setup screenTh e ADL Uplink rebroadcaster is pre-confi gured for serial communication with any PDL or ADL radio. As soon as RTK corrections from the Internet server are received, they are automatically passed to the attached radio for broadcast. It makes no diff erence how the radio is confi gured for this broadcast. If you wish to change any of the radio’s confi guration parameters, tap the Radio button.

You can reconfi gure the radio to use a diff erent protocol, channel or baud rate. When you are done, tap the OK button and back-arrow to return to the Main screen.

20

RTK Setup screenSo far, you have set up the ADL Uplink cellular modem to connect fi rst to the Internet and then to the RTK server. Now you will setup the ADL Uplink unit to actually download the corrections and send them out the serial port to the radio. Tap the RTK Repeater button to display the RTK Setup screen.

Tap the List button to download a list of diff erent RTK correction types. It may take a minute to display all the types available on the selected server. If the service you have subscribed to off ers more than one type, the diff erence is typically in the format used: RTCM 2.X, RTCM 3.X, CMR+, CMRx, etc.

Select the type that your rover GNSS receivers are set up to us and tap the Start button to stream RTK corrections to the radio. Th ese corrections will be calculated by the RTK server for the GPS coordinates listed on the RTK Setup screen. If you do not have a GPS position or if you wish to input the coordinates of the rover GNSS receiver, tap the small button with three dots, at the lower right of the screen. Th is displays the Manual position screen.

21

Tap the Latitude, Longitude and Altitude fi elds and use the soft keypad to manually enter coordinates. When you are done, tap the back-arrow. If you know you will always want to enter coordinates manually, uncheck the Automatic positioning box at the lower left.

Th e RTK Setup screen also displays the amount of data “U” uploaded to and the amount of data “D” downloaded from the RTK server. (Uploaded data consists of the user name and password, the geographic coordinates and housekeeping data.)

NOTE: If the cellular or Wi-Fi connection is ever dropped, the ADL Uplink rebroadcaster will automatically redial and reconnect. If it cannot get another connection, you should fi rst move to another area. Use the cellular signal strength indicator (the “bars”) to see if you have an Internet link.

To disconnect from the RTK server, tap the Stop button, exit the ADL Uplink program or turn off the unit.

Reconnecting to the RTK ServerTh e next time you want to use the ADL Uplink rebroadcaster:

• Turn on the unit, preferably in an area with an open view of the sky

• Confi rm that you have a cellular or Wi-Fi connection

• Check that the unit has a GPS position

• Launch the program

Using the previous confi guration, the ADL Uplink unit will automatically connect to the RTK server, download corrections and pass them to the radio for rebroadcast.

To stop the data stream, simply close the program.

Installing ADL Uplink program upgrades1. Put the upgrade CAB fi le on your PC.

2. Run Microsoft ActiveSync on your PC

3. Turn on the ADL Uplink unit and attach it to your PC with the USB-to-USB cable.

4. When ActiveSync sees the ADL Uplink unit, click the Folders button on ActiveSync and copy the two cab fi les to some folder on the ADL Uplink unit.

5. Use the ADL Uplink unit’s File Explorer app to navigate to this folder and double tap the ADL Uplink upgrade CAB fi le.

Installing additional software on your unitTh ird-party software designed for Windows Mobile is installed by running a setup program on the PC while the unit is connected over ActiveSync or Windows Mobile Device Center. Follow the setup instructions that came with your software. If prompted, perform a reset to complete the installation.

Working with the GPS Tap Start / Settings / System / System Information / Wireless to see if your unit has built-in GPS. COM2 is the dedicated hardware port for the built-in GPS (COM1 is dedicated to the external 9-pin). Th e GPS is compatible with applications that accept the NMEA position information using a default setting of 9600 bps.

Using A-GPSIf the GPS has been used in the prior 72 hours, Assisted GPS (A-GPS) will retain a memory of the satellite paths. Th e A-GPS satellite data is stored in memory for the satellites visible in your current position. Th erefore the ADL Uplink can lock on the satellites quickly, in less than 20 seconds in an open sky.

GPS settings If you are using only one GPS-aware application, these settings do not need to be changed. However, to use multiple GPS-aware applications, tap Start / Settings / System / GPS and select the following tabs:

Access: Th e GPS Intermediate Driver allows multiple applications to access the GPS receiver (disabled by default). To enable the GPS Intermediate Driver, select the check box.

Hardware: COM2 is the hardware port dedicated for the built-in GPS. Verify that COM2 is selected. Th e internal GPS communicates at 9600 baud by default. If it has been modifi ed by a third party program, adjust to match the receiver baud rate.

Programs: Programs that use GPS need to know which port to use to access GPS data. Ensure that the COM port on the GPS-aware application is set to the same port as shown in the Programs tab of the GPS applet port as shown in the Programs tab of the GPS applet. Th e programs port must be a diff erent port than the hardware port.

NOTE: Some GPS-aware applications may not communicate over GPD ports.

A-GPS: While Assisted GPS can improve time-to-fi rst-fi x, it may reduce accuracy in some situations. Uncheck the box next to Enable Assisted GPS and reboot your unit if you wish to disable it.

22

If you are unable to connect to the GPS using the default GPS settings, you can restore it to factory default settings by performing a shutdown, and leaving it shut down for approximately 5 minutes. See Power key features on page 10.

Using SatViewerYour ADL Uplink may have SatViewer™ installed that is ONLY for use with units with built-in GPS. External GPS receivers, Bluetooth GPS receivers, GPS CF cards or other external GPS devices (including other SiRF II or SiRF III GPS receivers) are not supported and may not work correctly with SatViewer.

On your ADL Uplink, tap Start / Settings / System / System Information / Wireless to see if it has built-in GPS. If it does, COM2 is the dedicated hardware port for the built-in GPS (COM1 is dedicated to the external 9-pin). Your ADL Uplink GPS receiver is compatible with applications that accept the NMEA position information using a default setting of 9600 bps.

Quick Start: Th e following steps will allow you to quickly connect to the GPS with default settings:

1. Start SatViewer by tapping Start / Programs / SatViewer.

2. Tap on the GPS tab.

3. Make sure the COM setting is set to COM2.

4. Tap Connect to GPS. Th e fi elds Lat, Lon, Spd, Az and Ht will all read ? until SatViewer connects to the GPS and obtains a satellite fi x. If you are attempting to get a satellite fi x for the fi rst time, it may take several minutes and it is recommended to position your ADL Uplink unit outside with no overhead obstructions.

5. Tap Sky. Lat and Lon will change to current latitude and longitude when a satellite fi x has been completed.

Welcome to SatViewer Your on-board GPS receiver features a 20-channel SiRF III GPS receiver. Th e typical expected accuracy for this GPS receiver is about fi ve to fi fteen meters. It has the capability of receiving correction signals (Satellite-Based Augmentation System, SBAS) which may improve the accuracy of the GPS. However, these correction signals are not consistently available in all locations. Th e typical expected accuracy of the GPS receiver with the correction signals is about three to fi ve meters in an open sky. Your ADL Uplink GPS receiver updates its position once every second. It may take several minutes to start tracking the fi rst time you try to use it because it needs time to update its position and download current satellite information from the GPS satellites. Th is process will occur faster in a location with open sky.

After your ADL Uplink has downloaded the current satellite information, Assisted GPS (A-GPS) will retain a memory of the satellite paths up to 72 hours. Th erefore the ADL Uplink can lock on the satellites quickly, in less than 20 seconds in an open sky.

SatViewer provides a way to quickly start using the GPS functionality of the ADL Uplink, but it is not a stand-alone mapping, GIS or navigation program by itself. SatViewer is useful for checking the GPS confi guration and enabling advanced features of your ADL Uplink GPS receiver when these settings are not made available in other applications. When changing any GPS settings or other settings, it is important to wait a few moments after tapping on the desired option to allow time for your ADL Uplink GPS receiver to implement the requested change. SatViewer communicates with your ADL Uplink GPS receiver to compute your current position, speed, direction (azimuth) and height. Th is information is displayed at the top of the screen along with other information about the satellite signals. Speed and direction measurements are only useful when your ADL Uplink GPS receiver is in motion. Standing in one position with your ADL Uplink GPS receiver may result in inaccurate readings in direction and speed. If you are not moving, direction is reported as “?” and speed is reported as “0”. Height calculations from a GPS receiver are typically not very accurate. Vertical accuracy is about two to three times worse than the horizontal accuracy). Units of measurement are only displayed in U.S. feet and heights are only displayed in height above mean sea level (MSL).

Th e pages of the application are accessed by tapping the various tabs, which are laid out in index card format. Th e information in each tab is described on the following pages.

Sky Tab

Sky Plot Graphic: Th e Sky Plot is a graphical representation of where the satellites are positioned in the sky. Th e top of the circle represents north, the center is straight up, and the farthest right point is east. Th e outer blue circle represents the horizon and the red circle represents the elevation mask. Th e light gray circles radiating out from the center are the zenith angles in ten degree increments. Th e lines bisecting the light gray circles divide the circle into thirty degree azimuths.

23

Th e satellite icons are color coded to indicate if they are used, unused, or SBAS satellites. Each icon is labeled with the corresponding satellite’s ID number (PRN). If Leave satellite SNR trails is checked, the path of the satellites are also marked by a dotted line as each satellite moves across the sky.

Status Indicators: Th e following four messages are displayed around the sky plot to indicate the current settings confi gured on other pages:

• Corrections Disabled / SBAS Enabled: displays if Satellite Based Augmentation System (SBAS) is enabled or disabled. When SBAS is enabled, your ADL Uplink GPS receiver will attempt to locate, track and use correctional data supplied from an SBAS satellite in order to improve accuracy. Th ere are a limited number of SBAS satellites available, so they may not be readily accessible in your area. Th is setting is confi gured in the Type fi eld on the DGPS page.

• In SiRF Bin. Mode / In NMEA Mode: indicates which mode you are running in. Some applications may require GPS data to be sent to the application in the form of a NMEA message, where other applications require the GPS data be sent as a SiRF Binary message. Most mapping and navigation applications can use the NMEA message. Th is setting is confi gured with the NMEA/SiRF Binary radio buttons on the GPS page.

• Elev. Mask: displays the current elevation mask. Th is is the minimum angle above the horizon that a satellite must be located before it is used and is represented on the sky plot by a red circle. Th is setting is useful when using the GPS in areas where there might be obstructions to the view of low fl ying satellites (e.g. around buildings or trees). A typical elevation mask setting is between 5 and 15 degrees to eliminate those satellites from being used to calculate a position. Th e purpose for this setting is to increase the accuracy of the GPS. However, by using this setting, you are reducing the total number of satellites that can be tracked and used by your ADL Uplink GPS receiver. Th e idea is to eliminate those satellites that may degrade the accuracy of your ADL Uplink GPS receiver. Th is is confi gured in the Masks section of the GPS page.

• Masks: Displays the current PDOP and HDOP mask values as confi gured in the Masks section of the GPS page. If the measured Dilution of Precision (DOP) value exceeds the value set for the corresponding mask, the resulting calculated position will be ignored. In general, as the value of the DOP decreases, the accuracy of the GPS position increases. DOP values greater than six usually indicate the GPS position data is of poor quality (due to poor satellite geometry) and the resulting positions are less accurate.

NOTE: DOPs can not be displayed in Binary Mode, however, the DOP masks are still in eff ect.

Satellite Icons• Unused: A GPS satellite whose signal is being received, but not being used for position calculations.

• Used: A GPS satellite that is being used to calculate your current position.

• SBAS: A Satellite Based Augmentation System (SBAS) satellite, which can be used for error corrections. (See the DGPS page for more information.)

Leave SNR trails: Creates a dot on the screen for all previous satellite positions that form a trail on the sky plot over time as the satellite moves across the sky.

DOPs Bar Graph: displays the various Dilution of Precision (DOP) values as explained below. DOPs are not displayed when SiRF Binary is selected on the GPS page.

• PDOP: displays the Position Dilution of Precision, which is a combination of HDOP, VDOP and Time Dilution of Precision. It will always be larger than HDOP and VDOP.

• HDOP: displays the Horizontal Dilution of Precision, which is a measure of the calculated accuracy of the solution. DOP has no units and lower numbers indicate better solution geometry. In general, the lower the DOP value, the better confi dence you have in the position reading from your ADL Uplink GPS receiver.

• VDOP: displays the Vertical Dilution of Precision, which is a measure of the calculated elevation.

Each DOP bar is color coded to indicate the DOP quality as follows:

Green: Th e DOP is less than three (best).

Yellow: Th e DOP is greater than three, but less than six.

Orange: Th e DOP is greater than or equal to six, but less than twenty.

Red: Th e DOP is greater than or equal to twenty (worst).

Signal vs. Satellite Bar Graph: shows all the visible satellites and their corresponding ID numbers (PRN) ranging from 1 to 32. Also, the PRN for any currently tracked SBAS satellite (ranging from 122 to 138) is displayed in this graph. Tapping any bar will also display the signal to noise ratio (SNR) value for that satellite. Th e color of each bar indicates the following:

Green: Good satellite signal strength. Satellite is used with an SNR greater than or equal to thirty dB.

Yellow: Fair satellite signal strength. Satellite is used with an SNR less than thirty dB.

Red: No signal or the signal strength is below the minimum allowable threshold. Satellite is not used.

24

GPS Tab

Connect to GPS / Disconnect from GPS Th is button either tries to establish a connection with the GPS receiver chip or disconnects the connection.

COM: used to select the COM port for communication between SatViewer and your ADL Uplink GPS receiver. Your ADL Uplink GPS receiver port is set to COM2 and a baud rate of 9600. Th e default SatViewer settings shouldn’t need to be changed to connect.

NOTE: Before changing COM port or baud rate settings, you must fi rst disconnect from your ADL Uplink GPS receiver before making the changes. After you have changed the COM settings, then you can re-attempt to connect to your ADL Uplink GPS receiver, using the Connect to GPS button.

Enabling the Microsoft GPS driverIf you would like to connect two or more programs to your ADL Uplink GPS receiver at the same time (such as SatViewer and a navigation program) you will have to turn the Microsoft GPS driver on by performing the following steps:

1. Tap Settings / System / GPS.

2. Tap the Access tab.

3. Tap Manage GPS automatically. Th is will turn on the Microsoft GPS driver. Ensure that the GPS program port is COM3 (or any other port available in the Microsoft GPS driver screen) and the GPS hardware port is COM2 with baud rate of 9600.

4. Th e Microsoft GPS driver will now allow multiple applications to connect to your ADL Uplink GPS receiver at the same time. Th is can be helpful so that your ADL Uplink GPS receiver can be controlled with SatViewer while other applications are also using your ADL Uplink GPS receiver.

5. In SatViewer and any other program using your ADL Uplink GPS receiver, change the COM port to COM3 (or the COM port specifi ed in Step 3 above). Both applications will connect to your ADL Uplink GPS receiver through the Microsoft GPS driver.

Restore Defaults:When connected to your ADL Uplink GPS receiver: Tapping the Restore Defaults tab will result in the following settings being changed:

• GPS receiver output will be set to NMEA mode

• Static Navigation will be turned OFF

• Smooth Tracking will be turned OFF

• Elevation mask is set to fi ve

• PDOP mask is set to eight

• HDOP mask is set to eight

• GPS status voice prompt is turned OFF

• NMEA message settings under the Advanced page are changed as follows:

o GGA – 1 seco GSA – 1 seco GLL – off o VTG – off o GSV – 1 seco RMC – off

• DGPS settings under the DGPS tab are set back to their defaults of Usage: Auto, Type: SBAS ON and SBAS Sat. PRN: Auto

• No change to any COM settings

Each of the above settings (except for the GPS status voice prompt) are sent and applied to your ADL Uplink GPS receiver.

When disconnected from your ADL Uplink GPS receiver: Tapping the Restore Defaults tab will result in the following settings:

• GPS receiver output will be set to NMEA mode

• Static Navigation will be turned OFF

• Smooth Tracking will be turned OFF

• Elevation mask is set to fi ve

• PDOP mask is set to eight

• HDOP mask is set to eight

• GPS status voice prompt is turned OFF

25

• NMEA message settings under the Advanced page are changed as follows:

o GGA – 1 seco GSA – 1 seco GLL – off o VTG – off o GSV – 1 seco RMC – off

NMEA message settings (set to default or otherwise) will be sent to your ADL Uplink GPS receiver and applied the next time you connect to your ADL Uplink GPS receiver (with output set to NMEA).

• DGPS settings under the DGPS tab are set back to their defaults of Usage: Auto, Type: SBAS ON and SBAS Sat. PRN: Auto

Since you are not connected to your ADL Uplink GPS receiver, none of the above changes are actually applied to your ADL Uplink GPS receiver. To apply these settings, you will need to fi rst connect to your ADL Uplink GPS receiver and then tap on the Restore Defaults button.

• If the Microsoft GPS driver is not used, the COM port gets set to COM2.

• If the Microsoft GPS driver is used, the COM port gets changed to its assigned program port.

• Baud rate is set to 9600

• Data bits are set to 8

• Flow is set to None

• Parity is set to None

• Stop bit is set to 1

To completely restore your ADL Uplink GPS receiver back to the factory settings, perform a system shut down on your ADL Uplink for a minimum of fi ve minutes before turning the unit back on and attempting to reconnect with your ADL Uplink GPS receiver in SatViewer. In order to perform a system shut down, press down and hold the Power button for a few seconds and then release. A Power Menu is displayed with diff erent options. Tap on the Shutdown button to put your ADL Uplink into a system shutdown. Th is procedure is benefi cial when you are unable to connect your ADL Uplink GPS receiver to SatViewer due to a change in the communications settings caused by another software application. In most cases, the factory reset procedure only needs to be used when another application has changed the settings of the ADL Uplink GPS receiver and you would like to set them back to their original confi guration.

NMEA / SiRF Binary: is where you choose to set your ADL Uplink GPS receiver to NMEA mode or SiRF Binary mode. When in SiRF Binary mode, DOP values are not available in the Sky page. Th e mode you select here will also determine the format for the information that can be viewed from the Data View page. Most GPS applications require that your ADL Uplink GPS receiver be set to output NMEA messages. Th ere are some specialized GPS applications which require the SiRF Binary output mode. Please consult the documentation of your GPS application to see which output format you should use and then choose that option via this setting.

Static Navigation: Th is feature keeps your ADL Uplink GPS receiver from showing the normal erratic positions when standing still. When checked, small changes in your position are interpreted as GPS error and your computed position will remain unchanged. For applications where you will be mapping or navigating at walking speed or slower, it is recommended to disable this feature, so even small changes in position will be shown.

Smooth Tracking: Th is feature smoothes the track generated by your ADL Uplink GPS receiver. When checked, movement is smoothed mathematically to reduce the seemingly jagged movement resulting from GPS error. For unfi ltered, raw GPS readings, you should leave this box unchecked. However, if you want to see a smoother overall position (e.g. while navigating), then turn this feature on via the checkbox.

NOTE: Both the Static Navigation and Smooth Tracking features modify your true GPS positions mathematically so these features should not be used when you need the most accurate GPS positions available.

Masks: Th ese defi ne limits that determine when a satellite will be used or not used.

• Elevation: Th is is the minimum angle above the horizon that a satellite must be located before it is used. A value of zero would essentially turn off the elevation mask. A value of ninety would mask all satellites. A typical elevation mask setting is between fi ve and fi fteen degrees to block tracking of those satellites potentially aff ected by multipath error due to obstructions (e.g. buildings or trees). Multipath error is error to the GPS position from the satellite signal bouncing off of objects before reaching the GPS receiver.

• PDOP: Th is is the maximum allowable Position Dilution of Precision (PDOP), which is a combination of HDOP, VDOP and Time Dilution of Precision. While exceeded, the GPS data will not be used for position calculations. Th is setting is advantageous when quality and reliability of your position are of concern. Typically, PDOP values of six or greater are considered “suspect” and therefore resulting positions are less reliable.

• HDOP: Th is is the maximum allowable Horizontal Dilution of Precision (PDOP), which is a measure of the geometrical quality of the solution. While exceeded, the GPS data will not be used for position calculations.

NOTE: DOPs can not be displayed in Binary Mode, however, the DOP masks are still in eff ect.

GPS status voice prompt: When checked, changes in GPS quality will result in an audible message indicating the change.

Advanced: When tapped, opens the Advanced GPS screen described on the following page.

26

Advanced GPS Page Return to Default Settings:

When connected to your ADL Uplink GPS receiver: Tapping the Return to Default Settings button, the following settings are changed and applied to your ADL Uplink GPS receiver:

• Resets NMEA strings to defaults of:

o GGA – 1 sec o GSA – 1 sec o GLL – off o VTG – off o GSV – 1 sec o RMC – off

NOTE: Th e COM settings are grayed out and cannot be changed until you disconnect from your ADL Uplink GPS receiver.

When disconnected from your ADL Uplink GPS receiver: Tapping the Return to Default Settings button, the following settings are changed:

• Resets NMEA strings to defaults of:

o GGA – 1 seco GSA – 1 seco GLL – off o VTG – off o GSV – 1 seco RMC – off

NMEA message settings (set to default or otherwise) will be sent to your ADL Uplink GPS receiver and applied the next time you connect to your ADL Uplink GPS receiver (with output set to NMEA).

• If the Microsoft GPS driver is not used, the COM port gets set to COM2.

• If the Microsoft GPS driver is used, the COM port gets changed to its assigned program port.

• Sets baud rate to 9600

• Data bits are set to 8

• Flow is set to None

• Parity is set to None

• Stop bit is set to 1

Since you are not connected to your ADL Uplink GPS receiver, none of the changes are actually applied to your ADL Uplink GPS receiver.

COM: used to select the COM port for communication between SatViewer and your ADL Uplink GPS receiver. Th is fi eld is also available on the GPS page for convenience and changing it in one location will automatically change it in the other location.

Baud: sets the speed for communications between your ADL Uplink GPS receiver and SatViewer. Th e baud rate of your ADL Uplink GPS receiver is 9600 by default. Please note, if you have used another application to change the baud rate of your ADL Uplink GPS receiver to 4800, it will take longer for your ADL Uplink GPS receiver to respond to changes made within SatViewer. During this period, you may see menu items grayed out while SatViewer is sending the new settings to your ADL Uplink GPS receiver.

Data Bits: should match the data bit rate set in the device you are communicating with.

Flow: should match the fl ow control set in the device you are communicating with.

Parity: should match the parity set in the device you are communicating with.

Stop bit: should match the stop bit set in the device you are communicating with.

NMEA Msg: Th is section allows you to control which NMEA messages are output by your ADL Uplink GPS receiver and the rate at which they are output. Th e GGA NMEA message is automatically enabled by default and cannot be disabled. You may change the frequency of output for the GGA NMEA message, but you may not disable it. Other NMEA messages listed may be disabled as well as changing the frequency of output. Th e ability to change the frequency of output and to disable certain messages is useful when communicating at a very low baud rate to prioritize which NMEA messages are sent. Each fi eld allows you to select a value from one to fi ve (measured in seconds), or to select OFF. For example, selecting three instructs the receiver to output the corresponding NMEA message once every three seconds. Selecting OFF instructs the receiver to never output the corresponding message. Th is setting is only applicable when you need to specify your ADL Uplink GPS receiver to send out very specifi c NMEA messages at specifi c times for your GPS application. Most users will not need to change this as the default NMEA settings will work for most GPS applications trying to display common GPS information (e.g. position, velocity, direction).

27

DGPS TabDiff erential GPS (DGPS) positioning involves subtracting a combination of ranges measured to various satellites from two or more receivers measuring the same satellites simultaneously. When the signals are subtracted, the major error sources cancel each other out.

Th e GPS receiver used with SatViewer can provide DGPS through the Satellite Based Augmentation System (SBAS), which uses multiple ground stations and then broadcasts corrections to the end users via SBAS satellites.

Usage: confi gures the DGPS requirements as follows:

• Auto: will use DGPS when available, but continue to provide autonomous (uncorrected) positions when DGPS is not available.

• DGPS Required: will only provide positions when DGPS is available. Autonomous positions will not be available. When DGPS data is available, it can be applied to your GPS position to increase the accuracy of your position reading.

• Ignored: will not provide DGPS positions even when available.

NOTE: Due to the limited number and availability of SBAS satellites in the sky, DGPS coverage from SBAS satellites may not always be available. Th erefore, it is recommended that you use the Auto setting where the GPS will use and apply DGPS data when available, but will continue providing positions even when DGPS is not available.

Type: allows you to select SBAS ON or SBAS OFF. (Currently SBAS is the only DGPS service available, but other DGPS systems may be available in the future.)

SBAS Sat. PRN: confi gures which SBAS satellite to use. Selecting Auto instructs the GPS receiver to automatically make the selection.

Return to Default Settings: If connected to your ADL Uplink GPS receiver, the following settings are changed and applied to your ADL Uplink GPS receiver:

• Restores DGPS settings back to default state:

o Usage: Auto

o Type: SBAS ON

o SBAS Sat PRN: Auto

If disconnected from your ADL Uplink GPS receiver this button has no eff ect on DGPS settings.

Data View Tab Th e Data View page allows you to capture and view the GPS data being sent to SatViewer by your ADL Uplink GPS receiver over the COM port. Th ere are two formats for data that can be viewed from this screen depending on if you are running in NMEA or SiRF Binary mode, as confi gured in the GPS page. Th is feature is useful if you have a need to view or store the raw GPS messages as they come out from your ADL Uplink GPS receiver in a textual format. Th is feature is for advanced GPS users who need the ability to store the raw GPS information as ASCII text in one large LOG fi le. Th is feature is intended to collect up to several minutes of data. It is not intended for extended data collection sessions.

When in NMEA mode, the data displayed is simply the raw NMEA codes being sent over the COM port, which are displayed in their original ASCII format.

When in SiRF Binary mode, the data being sent over the COM port is in binary format and therefore must be converted to ASCII text before it can be displayed in a useable format. Th is involves converting each binary message to hexadecimal text and adding a text tag to each message that explains what type of message it is.

28

Chars: Lists the number of characters captured to the buff er. Th e maximum amount of characters that can be stored to the buff er is approximately 64,000 characters. A “% full” indicator for the used buff er is provided for your convenience.

Capture: Begins capturing the data passing over the COM port and storing it to a buff er.

Stop: Stops capturing data and outputs the contents of the buff er to the screen.

Clear: Clears the buff er and any data listed on the screen.

View: Outputs the contents of the buff er to the screen while capturing data.

Save: Opens a new screen where the contents of the Data View screen can be saved to a fi le.

TroubleshootingWhat do I do to keep my battery from failing during a job? Consider carrying a fully charged spare battery in the fi eld. Th e unit is designed so that battery replacement can be easily done.

How do I delete fi les? Open File Explorer and browse to the fi le to be deleted. Touch and hold on the fi le and tap Delete from the menu that appears. Unlike PC’s, Windows Mobile does not support a Recycle Bin. Once you delete a fi le, it cannot be recovered.

How can I see fi le extensions or fi le attributes? Windows Mobile File Explorer does not support viewing fi le extensions like Windows Explorer on a PC. You can connect the unit to your PC and browse from the PC to view fi le extensions. (Refer to Connecting to a PC on page 18 for details.) Th ird-party fi le management programs are available for Windows Mobile devices that may support a Recycle Bin, viewing fi le extensions and more.

How can I tell how much memory is available? Tap Start / Settings / System / Memory to view available free storage and program memory. Tap Storage Card to view available memory on memory cards that may be installed. If there is more than one card installed, tap the dropdown arrow to select the diff erent cards.

How can I make the display more viewable? Tap Start / Settings / System / Backlight / Brightness to adjust the display brightness; however, this will reduce battery life. You can also change the background theme found under Start / Settings / Personal / Today. Confi rm that you have only one screen protector in place.

Can I use my SDIO device with my unit? SDIO devices work as long as they are supported with Windows 6 drivers. An Extended Cap, sold as an accessory, can be used for oversized SD cards if your device does not have the camera or barcode scanner.

Can I work with Microsoft Offi ce fi les in Word Mobile and Excel Mobile? Offi ce Mobile applications are trimmed-down versions of the PC Microsoft Offi ce applications and do not support all of the features that are supported by the PC applications. You can view simple documents and make simple changes on your unit.

Can I use my USB memory stick (or mouse, keyboard, cell phone or other USB device) with my unit? Connecting peripheral devices via USB requires the USB I/O Boot. Many USB devices may work. Check with the device manufacturer to see if the device is supported under Windows Mobile. Special drivers may need to be installed.

29

Caring for your UnitCase vent hole: A Gore-Tex membrane is used at the vent hole to equalize the atmospheric pressure within the unit and to prevent dust, water, etc. from entering. Th e vent must remain clear of any obstruction. Damage to the touchscreen will occur if the vent is covered. Covering the vent with stickers and labels may void the warranty.

Cleaning the unitUse a soft, dampened cloth with either water or a diluted mild detergent. If a mild detergent is used, ensure all soap residue is removed. Do not use any chemical cleaners and do not put the unit in the dishwasher.

Care of the touchscreenUse only the included stylus or other devices specifi cally designed for use with touchscreens. DO NOT use the metal screwdriver end of the stylus on the touchscreen or it will scratch your screen. Only use the spring-tip end of the stylus.

Th e use of ballpoint pens, nails or other sharp objects to operate the touchscreen will scratch and/or damage the unit. Keep the touchscreen clean by gently wiping the display, using a soft, dampened cloth with either clean water or glass cleaner.

Do not use abrasive cleaners directly on the display. Doing so may void your warranty. Use the screen protectors included with the unit to keep the touchscreen clean and protected, following the instructions provided on the screen protector package.

Mechanical shockTh e unit is designed to resist damage for drops up to 4 ft (1.22 meters). However, you should protect the display from impact, pressure, or abrasive substances that can scratch it or crack it. Th e unit should not be dropped unnecessarily.

Environmental ConsiderationsTh e unit’s rugged design allows you to run your applications in harsh outdoor environments. Here are some considerations that will help you get the most out of your unit when working in very wet, hot or cold conditions.

WaterTh is unit is designed to withstand accidental immersion. To maintain the unit’s water resistant seal, it is important that the cap screws are fastened. Keep the bottom boot and its connectors as dry as possible. If the boot does get wet, dry off the contacts as much as possible. Removal of the back case torx screws or failure to reattach the cap or boot could cause leakage and may void your warranty.

Temperature range Th e operational temperature range is from -4 °F to +140 °F (-20 °C to +60 °C). Although the unit is designed to be rugged, do not leave it in direct sunlight or in a vehicle in the sunlight for extended periods.

Batteries perform best at room temperature. Th e battery has a stable capacity as temperatures rise; however, the colder the temperature, the greater the reduction in available battery life. Under very cold conditions (-4 °F / -20 °C and below), the battery life will be shortened. To improve the battery performance in very cold conditions, consider carrying a fully charged, spare battery in a warm place ( for instance, keeping them inside your coat). Th e unit is designed for battery replacement to be easily done.

Vent hole

30

Environmental Specifi cationsTEMPERATURE Operation: -4 °F to +140 °F (-20 °C to +60 °C)

Storage: -4 °F to +122 °F (-20 °C to +50 °C)

SHOCK MIL-STD-810F, Method 503.4

HUMIDITY MIL-STD-810F, Method 507.4

WATER IP67, sealed against accidental immersion (submersible to 1 meter for 30 minutes), MIL-STD 810F, Method 512.4, Procedure 1

DROP MIL-STD-810F, Method 516.5, Procedure IV26 drops @4 ft. (1.22 m) onto plywood over concrete; 6 drops @-22 °F (-30 °C), 6 drops @+140 °F (+60 °C)

SAND AND DUST IP67, sealed against dust, MIL-STD 810F, Method 510.3, Procedure I & II

VIBRATION MIL-STD 810F Method 514.5, Procedure I & II

ALTITUDE MIL-STD 810F, to 15,000 ft (4572 m) at a nominal temp. of +73 °F (+23 °C), Method 500.4, Procedures I, II, & III

EMI Meets FCC class B requirements

ROHS COMPLIANT Th is product complies with international RoHS regulations

Hardware Specifi cationsOS Windows Mobile 6.1

CPU Marvel PXA320 XScale 806 MHz

RAM (VOLATILE) 128 MB DDR SDRAM

FLASH STORAGE 512 MB to 6 GB of nonvolatile NAND Flash storage

DISPLAY 480 x 640 pixel (VGA) color TFT with LED backlight

KEYPAD PDA or Data Numeric

BATTERY LIFE 15 hours continuous room temperature operation with default settings and no use of embedded radios

BATTERY CHARGING 4 to 4.5 hours to full charge

BATTERY CAPACITY 5200 mAh Li-Ion rechargeable

POWER SUPPLY Cincon TR30RAM050. Output DC 5.0 V 4.0 A

POWER Input: DC 5.0 V 4.0 A

I/O BOOTS USB Boot: Mini-USB client, USB host, Audio Jack, Power Serial Boot: Mini-USB client, RS-232 serial (9-pin), Power

SOUND Integrated sealed speaker and microphone. Audio jack is for a headset with mono speaker and microphone

EXPANSION PORTS Standard: SD slot, CF Type II or USBColor Digital Camera: SD slot, Camera (5 megapixel)Barcode Scanner & Camera: SD slot, Scanner, Camera

INTEGRATED WIRELESS All units have Integrated BluetoothOptional cellular, Wi-Fi and GPS

31

Regulatory InformationU.S.A.Th is device complies with Part 15 of the FCC Rules. It is tested to comply with FCC standards for home or offi ce use. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Th is equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Th ese limits are designed to provide reasonable protection against harmful interference in a residential installation. Th is equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit diff erent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CanadaTh is digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada.

Exposure to Radio Frequency (RF) SignalsYour device contains a radio transmitter and receiver. Th e radiated output power is far below the international radio frequency exposure limits. Th ese limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. Th e guidelines are based on the safety standards previously set by international standards bodies:

• American National Standards Institute (ANSI) IEEE. C95.1-1992.

• National Council on Radiation Protection and Measurement (NCRP).

Report 86. 1986.

• Int’l Commission on Non-Ionizing Radiation Protection (ICNIRP) 1996.

• Ministry of Health (Canada), Safety Code 6. Th e standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.

Use of unauthorized or modifi ed antennas may impair call quality and damage the phone, causing loss of performance. To assure optimal phone performance and ensure human exposure to RF energy is within the guidelines set forth in the relevant standards; always use your device only in its normal-use position. Avoiding contact with the antenna area when the phone is IN USE optimizes the antenna performance.

Carrying the unitFor body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.

SAR Frequency (MHz) Highest Multiband SAR Value (1g mW/g)

824-849 1.290

1850-1910 0.521

2400-2483.5 0.099

32

Declaration of ConformityEuropeAccording to ISO / IEC Guide 22 and EN 450 14

Manufacturer’s Name: Trimble Navigation Limited.

Manufacturer’s Address: PO Box 947, Corvallis, OR 97339 USA

Declares, under our sole responsibility, that the product:

Product Name: Handheld Data Collector

Model Number: ADL Uplink

Product Options: ALL

Conforms to the following Product Specifi cations:

R&TTE Directive 1999/5/EC EN 61000-3-2 (2000)

ETSI EN 300 328 V1.6.1 (2004) EN 61000-3-3 (2001)

ETSI EN 301 489-1 V1.5.1 (2004) EN 61000-4-3 (2002)

ETSI EN 301 489-17 V1.2.1 (2002) EN 61000-4-2 (2001)

EN 55022 (1998) EN 61000-4-4 (2004)

CISPR 22 (2005) EN 61000-4-5 (2001)

EN 55024 (1998), Amendments A1:2001, A2:2003 EN 61000-4-6 (2004)

EN 60950-1 (2001) EN 61000-4-11 (2004)

CFR 47, Part 15, Subpart B

Supplementary InformationIn addition, the product is battery powered and the AC adapter provided with this product has been certifi ed to IEC 60950 +A1, A2, A3, A4, A11.

As manufacturer, we declare under our sole responsibility that the equipment follows the provisions of the Standards stated above.

Corvallis, OR USA

Importer of Record: Trimble European Regional Fulfi llment Center,

Logistics Manager, Meerheide 45, 5521DZ Eersel, Netherlands.

CAUTION: Only approved accessories may be used with this equipment. In general, all cables must be high quality, shielded, correctly terminated and normally restricted to two meters in length. AC adapters approved for this product employ special provisions to avoid radio interference and should not be altered or substituted.

Unapproved modifi cations or operations beyond or in confl ict with these instructions for use may void authorization by the authorities to operate the equipment.

Safe Use of your Unit

RepairDo not attempt to dismantle the unit for repair. Th ere are no user-serviceable parts inside. For service, use the contact details listed on the cover of this manual or contact your local dealer.

Battery safetyLithium-Ion batteries are classifi ed by the U. S. Federal Government as non-hazardous waste and are safe for disposal in the normal municipal waste stream. Th ese batteries contain recyclable materials and are accepted for recycling.

1) Do not disassemble or open, crush, bend or deform, puncture, or shred the battery. Th ere are no user-serviceable parts in the battery pack.

2) Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fi re, explosion, or other hazard. Do not expose to temperatures above +158 °F (+70 °C).

3) Use only the battery for the system for which it was specifi ed.

4) Only use the battery with a charging system that has been qualifi ed with the system per this standard. Use of an unqualifi ed battery or charger may present a risk of fi re, explosion, leakage, or other hazard.

33

5) Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.

6) Replace the battery only with another battery that has been qualifi ed with the system per this standard. Use of an unqualifi ed battery may present a risk of fi re, explosion, leakage, or other hazard.

7) Promptly dispose of used batteries in accordance with local regulations.

8) Battery usage by children should be supervised.

9) Non approved batteries will not function in the device.

10) Avoid dropping the unit or battery. If dropped, especially on a hard surface, and the user suspects damage to the battery, take it to a service center for inspection.

11) Improper battery use may result in a fi re, explosion, or other hazard.

12) In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the aff ected area with large amounts of water and seek medical advice.

13) Seek medical advice immediately if a battery has been swallowed.

AC adapter safetyUse only AC and vehicle adapters intended for the unit. Other external power sources may damage your product and void the warranty. Certifi cation of this Class III product is only valid with the power supply - Cincon TR30RAM050.

• Ensure the input voltage on the adapter matches the voltage in your location. Ensure the adapter has prongs compatible with your outlets.

• AC adapters are designed for indoor use only. Avoid using the AC adapter in wet areas.

• Unplug the AC adapter from power when not in use.

• Do not short the output connector.

Telecommunications & Internet Association (TIA) informationHearing Aids: Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may want to consult your service provider, or call the customer service line to discuss alternatives.

Pacemakers and Other Medical Devices: Th e Health Industry Manufacturers Association recommends a minimum separation of six inches be maintained between a handheld wireless phone and a pacemaker to avoid potential interference with the pacemaker. Th ese recommendations are consistent with the independent research by and recommendations of Wireless Technology Research. Persons with pacemakers should use the ear opposite the pacemaker to minimize the potential for interference. If you have any reason to suspect that interference is taking place, turn the phone OFF immediately.

If you use any other personal medical device, consult the manufacturer of your device to determine if they are adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information.

Turn the phone OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.

34

Part Name Lead (Pb)

Mercury (Hg)

Cadmium (Cd) Hexavalent Chromium (Cr6+)

Poly-brominated biphenyls (PBB)

Poly-brominated diphenyl ethers (PBDE)

Printed Circuit Assemblies

X O O O O O

Display

X O O O O O

Keypad

X O O O O O

Housing

O O O O O O

Hardware

O O O O O O

Product Period does not include these items

BatteryX O O O O O

AC adapter X O O O O O

cable

O O O O O O

Manual

O O O O O O

Hand strap

O O O O O O

Stylus pkg. O O O O O O

Companion CD

O O O O O O

Toxic and Hazardous Substances and Elements

Environmental HazardsTh e product complies with international RoHS regulations.

35

NOTICE for Our European Union CustomersFor product recycling instructions and more information, please go to: www.trimble.com/env.

Recycling in Europe:

To recycle WEEE (Waste Electrical and Electronic Equipment products that run on electrical power), call +31 497 53 24 30 and ask for the “WEEE Associate.”

Or

Mail a request for recycling instructions to:

Trimble Europe BV

c/o Menlo Worldwide Logistics

Meerheide 45

5521 DZ Eersel, NL

Th is product complies with international regulations for Restriction on Hazardous Substances Directive (RoHS)

Windows Mobile:

www.microsoft.com/windowsmobile/default.mspx

Section 508 Support: Download accessibility templates for our products.

www.Trimble.com/section508

©2011, Pacifi c Crest. All rights reserved. ADL Uplink, Trimble and the Globe & Triangle logo are trademarks of Trimble Navigation Limited, registered in the United States Patent and Trademark Offi ce and in other countries.

ActiveSync, Microsoft, Outlook, Windows, the Windows logo, and Windows Mobile are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Microsoft products are licensed to OEMs by Microsoft Licensing, Inc., a wholly owned subsidiary of Microsoft Corporation.

All other brand names and trademarks are property of their respective owners.

Display images shown may vary slightly from actual display. Specifi cations and data subject to change.

Pacifi c Crest

510 DeGuigne Drive

Sunnyvale, CA 94085

USA

+1.408.481.8070

www.Pacifi cCrest.com 71888-21 Rev A

September 2011