Monthly Notifications Register - SUTN · 2011-11-07 · Information procedure Page 1 Monthly Notifications Register Notifications registered at CCMC from 2011-09-01 to 2011-09-30

Information procedure Page 1

Monthly Notifications Register

Notifications registered at CCMC from 2011-09-01 to 2011-09-30

Register issued on : 2011-10-07

A list of subsectors can be found at the end of this document.




Sector A : SERVICES


Page 3Subsector A01: TOURIST SERVICES

Subsector : A01 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024108/0001 Project EstablishedICS : 01.080.10, 45.100, 97.220.10National Ref : ÖNORM S 4610Title : Signs for use of ropeways, ski-lifts and other climbing aids - Requirements and designScope : The present Austrian Standard specifies requirements for and the design of signs used for

ropeways for transport of persons (funicular railways, cable railways with pendulum or circulation service, chair railways, chair lifts) and for ski-lifts. The specifications of this ÖNORM do not cover areas where the road traffic regulations are applicable or which concern occupational safety, transport of dangerous goods or fire protection. NOTE- For better emphasis within wide-area guiding systems, other writing systems or coloured background may be used for indications if this supports the orientation of the viewer and does not affect the legibility of the information. Crossed out symbols representing prohibition signs shall not impede the identification of these symbols

Relatedness :National : New

Subsector : A01 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024109/0001 Project EstablishedICS : 01.080.10, 97.220.10National Ref : ÖNORM S 4611Title : Signs for use in organised skiing areas - Requirements, design and classificationScope : The present Austrian Standard specifies requirements for and the design of signs used in

organised skiing areas. Furthermore, it represents the basis for the classification of the different levels of difficulty as well as for marking and labelling within the organised skiing area. The specifications of this ÖNORM do not cover areas where the road traffic regulations are applicable or which concern occupational safety, transport of dangerous goods or fire protection.


Subsector : A01 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024110/0001 Project EstablishedICS : 01.080.10, 97.220.10National Ref : ÖNORM S 4615Title : Signs for the use of cross country tracks and winter hiking trails - Requirements, design

and classificationScope : The present Austrian Standard specifies requirements for and the design of signs used for

cross country tracks and winter hiking trails. Furthermore, it represents the basis for the classification of cross country tracks in different levels of difficulty as well as for marking and labelling of cross country tracks and winter hiking trails. At present, a classification of cross country tracks and winter hiking trails is not scheduled in the present ÖNORM (see 6.2). The specifications of this ÖNORM do not cover areas where the road traffic

Page 4

Scope : regulations are applicable or which concern occupational safety, transport of dangerous goods or fire protection For better emphasis within wide-area guiding systems, other writing systems or coloured background may be used for indications if this supports the orientation of the viewer and does not affect the legibility of the information. Crossed out symbols representing prohibition signs shall not impede the identification of these symbols.


Subsector : A01 Registration Date : 2011-09-13Organization : AENORCountry : SpainProject ID : P0038237/0001 Project EstablishedICS :National Ref : PNE 167013Title : Hospitality. Catering services. Service provision requirementsScope : This standard establishes the requirements for the quality provision of the service in all

catering modalities

Relatedness :

National :REV/AMD UNE 167001:2006, UNE 167002:2006, UNE 167003:2006, UNE 167005:2006, UNE 167007:2006, UNE 167008:2006, UNE 167009:2006, UNE 167010:2006, UNE 167011:2006

Subsector : A01 Registration Date : 2011-09-13Organization : AENORCountry : SpainProject ID : P0038238/0001 Project EstablishedICS :National Ref : PNE 167014Title : Hospitality. Food safety requirements and procedures for core units of production and

distribution in full cook and chill.Scope : This standard establishes food safety requirements and procedures for production units in

cook and chill industry.


** End of Subsector **

Subsector A99: UNDETERMINED

Subsector : A99 (Secondary Subsector)

Registration Date : 2011-09-01

Organization : BSICountry : United KingdomProject ID : 01102109/0001 Project EstablishedICS :National Ref : BS 8900Title : Guidance for managing sustainable development


Page 5** End of Subsector **

** End of Sector **




Sector B : BUILDING AND CONSTRUCTION


Page 7Subsector B01: FIRE PROTECTION

Subsector : B01 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024104/0001 Project EstablishedICS : 13.220.20, 13.320National Ref : ÖNORM F 3052Title : Fire detection and fire alarm systems - Alarm transmission systemsScope : This ÖNORM defines requirements for alarm transmission systems for fire detection and

fire alarm systems and the components for alarm transmission systems which are at least necessary.


Subsector : B01 Registration Date : 2011-09-01Organization : PKNCountry : PolandProject ID : 00244185/0001 Project EstablishedICS : 13.220.10National Ref : prPN-M-51501Title : Fire-fighting equipment -- Fire axesScope : Division for two types was determined - lightweight and heavyweight. The dimensions were

delivered on the inserted drawings. There were settled requirements, packing, preserving and transport, examinations, proceeding with the lot (fire axes) admitted as out of line with the requirements of the norm


Subsector : B01 Registration Date : 2011-09-28Organization : UNICountry : ItalyProject ID : 70001650/0001 Project EstablishedICS : 13.220.20National Ref : U70001650Title : Initial verification and maintenance of gaseous fire-extinguishing systemsScope : This standard specifies the procedures the procedures for initial verification, surveillance,

regular control and maintenance for gaseous fire extinguishing systems.

Relatedness :National : REV/AMD UNI 11280:2008


Subsector B02: STRUCTURES

Subsector : B02 Registration Date : 2011-09-21Organization : SNV Draft Issue Date : 2011-09-20Country : Switzerland Latest Date for Comments : 2011-11-18Project ID : CH110021/0001 Draft for public enquiryICS : 91.060.10National Ref : SIA 329

Page 8

Title : Curtain walling

Relatedness :National : REV/AMD SIA 329 (2008)


Subsector B03: CONCRETE

Subsector : B03 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175662/0001 Project EstablishedICS :National Ref : XP P18-463Title : Concrete - Testing gas permeability on hardened concrete


Subsector : B03 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175740/0001 Project EstablishedICS :National Ref : PR NF P18-513Title : Pozzolanic addition for concrete - Metakaolin - Definitions, specifications and conformity

criteria


Subsector : B03 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175798/0001 Project EstablishedICS :National Ref : NF P18-509Title : Additions for concrete - Siliceous additions - Specifications and conformity criteria


Subsector : B03 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038269/0001 Project EstablishedICS :National Ref : PNE 83994-1INTitle : Durability of concrete. Strategy on the assessment of durability by levels. Part 1:

Assessment methodsScope : This technical report describes the methods for the assessment of durability in concrete

structures, classifying them in implicit and explicit methods.

Page 9



Subsector B08: DOORS AND WINDOWS

Subsector : B08 Registration Date : 2011-09-21Organization : SNV Draft Issue Date : 2011-09-20Country : Switzerland Latest Date for Comments : 2011-11-18Project ID : CH110022/0001 Draft for public enquiryICS : 91.060.50National Ref : SIA 331Title : Windows and door height windows

Relatedness :National : REV/AMD SIA 331 (2008)

Subsector : B08 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175741/0001 Project EstablishedICS :National Ref : PR NF DTU 36.2 P2Title : Building work - Interiors wood joinery - Part 2 : Contract bill of special administrative

model clauses


Subsector : B08 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175742/0001 Project EstablishedICS :National Ref : PR NF DTU 36.2 P1-2Title : Building works - Interiors wood joinery- Part 1-2 : General criteria for selection of

materials


Subsector : B08 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175743/0001 Project EstablishedICS :National Ref : PR NF DTU 36.2 P1-1Title : Building works - Interiors wood joinery - Part 1-1 : Contract bill of technical model

clauses


Page 10


Subsector B09: THERMAL MATTERS

Subsector : B09 Registration Date : 2011-09-13Organization : SFS Draft Issue Date : 2011-04-14Country : Finland Latest Date for Comments : 2011-06-20Project ID : 0000E271/0001 Draft for public enquiryICS :National Ref :Title : Insulation of pipes, vessels and equipment. Test methods of insulating and covering

materials


Subsector : B09 Registration Date : 2011-09-13Organization : SFS Draft Issue Date : 2011-04-14Country : Finland Latest Date for Comments : 2011-06-20Project ID : 0000E272/0001 Draft for public enquiryICS :National Ref :Title : Insulation of pipes, vessels and equipment. Cold insulation


Subsector : B09 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024103/0001 Project EstablishedICS : 91.120.10National Ref : ÖNORM B 8110-7Title : Thermal insulation in building construction - Part 7: Recommended thermal insulation

calculation valuesScope : The present Austrian Standard provides default values as well as optimum values for

technical thermal insulation calculation values for (building) products. They can either be used as existing default values within the framework of the establishment of an energy certificate for existing buildings and default values for new buildings for the preparation of an energy certificate for the new building without further evidence, or as optimum values for enabling of building methods with minimized building part thicknesses for the establishment of an energy certificate for the new building with additional evidence.



Subsector B14: GEOTECHNICS

Subsector : B14 Registration Date : 2011-09-13Organization : DIN Draft Issue Date : 2011-05-16Country : Germany Latest Date for Comments : 2011-07-31

Page 11

Project ID : 00515739/0001 Draft for public enquiryICS : 93.020National Ref : DIN SPEC 18140Title : Application document to DIN EN 1536:2010-12 - Execution of special geotechnical

works - Bored piles



Subsector B18: SCAFFOLDING

Subsector : B18 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175669/0001 Project EstablishedICS :National Ref : PR NF P 93-354/A1Title : Building site equipment - Individual mobil plateform- Product specification and test

methods


Subsector : B18 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175670/0001 Project EstablishedICS :National Ref : PR NF P93-355/A1Title : Building site equipement - Temporary peripheral protection for water-resistance works in

roof - Product specification, test methods

Relatedness :National : REV/AMD NF P93-355:201010 (P93-355)


Subsector B22: WALLCOVERINGS

Subsector : B22 Registration Date : 2011-09-06Organization : SNV Draft Issue Date : 2011-08-31Country : Switzerland Latest Date for Comments : 2011-10-28Project ID : CH110018/0001 Draft for public enquiryICS : 91.180National Ref : SIA 242Title :

Plastering and dry construction works

Relatedness :National : REV/AMD SIA V242/1 (1994)

Subsector : B22 Registration Date : 2011-09-06Organization : SNV Draft Issue Date : 2011-08-31

Page 12

Country : Switzerland Latest Date for Comments : 2011-10-28

Project ID : CH110019/0001Draft for public

enquiryICS : 91.180National Ref : SIA 118/242Title : General conditions for Plastering and dry construction works

Relatedness :National : REV/AMD SIA V242/1 (1994)


Subsector B25: GAS DISTRIBUTION INSTALLATION AND RELATED EQUIPMENT

Subsector : B25 Registration Date : 2011-09-28Organization : UNICountry : ItalyProject ID : 01169233/0001 Project EstablishedICS : 91.140.40National Ref : E01169233Title : Gas measurement systems - Hourly based gas metering systems - Part 3: CTR ProtocolScope : This technical specification describes the characteristics of the CTR protocol, defined by

UNI TS 11291-1. The protocol is designed to function date transport with efficiency and safety, considering that it is implemented on devices with limited alphanumeric and / or special communication systems such as GSM-SMS plots that require the use of limited in length.

Relatedness :National : REV/AMD UNI/TS 11291-3:2010

Subsector : B25 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038239/0001 Project EstablishedICS :National Ref : PNE 60402-1:2008/1MTitle : Gaseous fuels. Pressure regulator with an inlet MOP up to 0,4 bar and an outlet MOP

up to 0,05 bar. Part 1: Regulators with an incorporated low pressure cut-off safety valve with an equivalent flow rate up to 4,8 m3 (n)/h of air.

Scope : This standard establishes the technical requirements for the design and operation, as well as for testing and marking of the pressure regulators with an inlet MOP up to 0,4 bar and an outlet MOP of 0,05 bar with an incorporated low pressure cut-off safety valve with an equivalent flow rate up to 4,8 m³ (n)/h of air to be used in gas receiving installations supplied with natural gas or LPG.

Relatedness :National : REV/AMD UNE 60402-1:2008

Subsector : B25 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038240/0001 Project EstablishedICS :National Ref : PNE 60402-2:2008/1M

Page 13

Title : Gaseous fuels. Pressure regulator with an inlet MOP up to 0,4 bar and an outlet MOP up to 0,05 bar. Part 2: Regulator with a MOP greater than 150 mbar, with an incorporated minimum low pressure cut-off safety valve, with a maximum pressure safety valve and an equivalent flow rate up to 4,8 m3 (n)/h of air.

Scope : This standard establishes the technical requirements for the design and operation, as well as for testing and marking of the pressure regulators with an inlet MOP greater than 150 mbar, with an incorporated low pressure cut-off safety valve, with a maximum pressure safety valve and an equivalent flow rate up to 4,8 m³ (n)/h of air to be used in receiving installations supplied with natural gas.

Relatedness :National : REV/AMD UNE 60402-2:2008


Subsector B26: ROAD BUILDING AND MAINTENANCE

Subsector : B26 Registration Date : 2011-09-28Organization : UNICountry : ItalyProject ID : 71021791/0001 Project EstablishedICS : 93.080.10National Ref : U71021791Title : Construction and maintenance for infrastructure civil building - Criteria for materials use

- Part 1: Soils and mixtures of loose aggregatesScope : The standard contains the useful instructions for the application in Italy of UNI EN ISO

14688, UNI EN 13242, UNI EN13285 and gives information of the soil classification, the aggregates designation and their unbound misture, and the criteria related to the evaluation of conformità. The standard show the technical characteristics common values relatively to the single end use.


Subsector : B26 Registration Date : 2011-09-23Organization : SNV Draft Issue Date : 2011-09-15Country : Switzerland Latest Date for Comments : 2011-10-27Project ID : CH110020/0001 Draft for public enquiryICS : 59.080.70National Ref : SN 670090Title : Geosynthetics, basic standard

Relatedness :National : REV/AMD SN 670090 (2010)


Subsector B27: WATERPROOFING MATERIALS

Subsector : B27 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175587/0001 Project EstablishedICS :

Page 14

National Ref : PR NF X46-035Title : Lead diagnosis - Lead search before works


Subsector : B27 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175588/0001 Project EstablishedICS :National Ref : PR NF X46-024Title : Abestsos survey - Evaluation of the risks of exposure to inhalation of asbestos fibers

and decision-making support



Subsector B99: UNDETERMINED

Subsector : B99 (Secondary Subsector)


Organization : BSICountry : United KingdomProject ID : 01102109/0001 Project EstablishedICS :National Ref : BS 8900Title : Guidance for managing sustainable development


Subsector : B99 Registration Date : 2011-09-15Organization : SIS Draft Issue Date : 2011-09-15Country : Sweden Latest Date for Comments : 2011-11-15Project ID : 04604866/0002 Project EstablishedICS :National Ref : 46004866Title : Vibration and shock - Guidance levels for blasting-induced vibration in buildingsScope : The standard gives guidance for the expected blast-induced vibrations in buildings. Remove

different guidance values on type of construction, type of building, type of soil, distance between building and blast holes. The risk analysis will be revised and harmonised to state of the art of blast technology.


Subsector : B99 Registration Date : 2011-09-08Organization : NENCountry : NetherlandsProject ID : 50001680/0001 Project Established

Page 15

ICS : 27.010National Ref : NPR 8799:2011 Concept nlTitle : Substations for electrical power distribution situated at specific locationsScope : This document focus on the electrical power distribution on specifici locations and is

primarily applicable for the use with property development and / or environmental planning


Subsector : B99 Registration Date : 2011-09-08Organization : NENCountry : NetherlandsProject ID : 50001682/0001 Project EstablishedICS : 91.060.10National Ref : NTA 8344:2011 Concept nlTitle : Site curtains - SafetyScope : This technical agreement contains safety requirements for site curtains to reduce the

possibility of accidents.


Subsector : B99 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175664/0001 Project EstablishedICS :National Ref : PR NF DTU 60.11 P3Title : Building works - Calculation rules for sanitary installations and rainwater draining off -

Part 3 : Rain water draining


Subsector : B99 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175665/0001 Project EstablishedICS :National Ref : PR NF DTU 60.11 P2Title : Building works - Calculation rules for sanitary installations and rainwater draining off -

Part 2 : Waste and black water draining


Subsector : B99 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175666/0001 Project EstablishedICS :

Page 16

National Ref : PR NF DTU 60.11 P1-2Title : Building works - Calculation rules for sanitary installations and rainwater draining off -

Part 1-2 : design and calculation for looped networks


Subsector : B99 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175667/0001 Project EstablishedICS :National Ref : PR NF DTU 60.1 P1-1-3Title : Building works - Sanitary plumbing in residential buildings - Sanitary equipments and

sanitary warm water production equipments - Part 1-1-3 : Contract bill of technical model clauses


Subsector : B99 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175668/0001 Project EstablishedICS :National Ref : PR NF DTU 60.1 P1-1-2Title : Building works - Sanitary plumbing in residential buildings - water draining networks -

Part 1-1-2 : Contract bill of technical model clauses



** End of Sector **




Sector C : CHEMICALS, CHEMICAL ENGINEERING AND FOOD PRODUCTS


Page 18Subsector C01: Food products

Subsector : C01 Registration Date : 2011-09-13Organization : AENORCountry : SpainProject ID : P0038131/0001 Project EstablishedICS :National Ref : PNE 195004Title : Trazability of fishery products in the whole chain.Scope : This project provides guidance to comply with correct identification requirements of fishery

products aiming at complying with legal requirements on trazability through the whole chain, from fishing to commercialization.



Subsector C02: PAINTS AND RELATED PRODUCTS

Subsector : C02 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038337/0001 Project EstablishedICS :National Ref : PNE 48315-2Title : Paints and varnishes. Determination of anticorrosive properties of organic coatings by

the accelerated cyclic electrochemical technique (ACET). Part 2: Examples of spectra and relaxation plots of polymer-coated specimens

Scope : This standard refers to the determination of anticorrosive properties of organic coating by means of the electrochemical accelerated cyclic technique (ACET). The technology is based on the application of cycles consisting of sequences of EIS measures, cathode polarizations and potential relaxation on the tested systems accelerating its degradation.



Subsector C03: CHEMISTRY

Subsector : C03 Registration Date : 2011-09-12Organization : SFS Draft Issue Date : 2011-04-14Country : Finland Latest Date for Comments : 2011-06-20Project ID : 0000E273/0001 Draft for public enquiryICS :National Ref :Title : Dangerous chemicals. Labelling of tanks



Subsector C06: ESSENTIAL OILS

Page 19

Subsector : C06 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038282/0001 Project EstablishedICS :National Ref : PNE 84655Title : Cosmetic raw materials. Plant extracts. Hedera hydroglycolic extract (Hedera helix L.).Scope : This standard determines the specifications required by the Hedera helix L. Hydroglycolic

Extract in cosmetic uses.

Relatedness :National : REV/AMD UNE 84655:2006

Subsector : C06 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038283/0001 Project EstablishedICS :National Ref : PNE 84656Title : Cosmetic raw materials. Plant extracts. Green tea hydroglycolic extract (Camellia

sinensis L.).Scope : This standard determines the specifications required by the Green tea Hydroglycolic Extract

in cosmetic uses.


Subsector : C06 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038286/0001 Project EstablishedICS :National Ref : PNE 84657Title : Cosmetic raw materials. Plant extracts. Ginkgo biloba hydroglycolic extract (Ginkgo

Biloba L.).Scope : This standard determines the specifications required by the Ginkgo Biloba Hydroglycolic

Extract in cosmetic uses.



** End of Sector **




Sector F : FUNDAMENTAL STANDARDS


Page 21Subsector F02: UNITS & SYMBOLS

Subsector : F02 Registration Date : 2011-09-12Organization : SFS Draft Issue Date : 2011-08-31Country : Finland Latest Date for Comments : 2011-11-01Project ID : 0000E274/0001 Draft for public enquiryICS :National Ref :Title : Quantities and units. Mass and force

Relatedness :National : REV/AMD SFS 3991 (1991)

Subsector : F02 Registration Date : 2011-09-12Organization : SFS Draft Issue Date : 2011-08-31Country : Finland Latest Date for Comments : 2011-11-01Project ID : 0000E277/0001 Draft for public enquiryICS :National Ref :Title : Quantities and units. Temperature


Subsector : F02 Registration Date : 2011-09-12Organization : SFS Draft Issue Date : 2011-08-31Country : Finland Latest Date for Comments : 2011-11-01Project ID : 0000E278/0001 Draft for public enquiryICS :National Ref :Title : Quantities and units. Pressure



Subsector F05: MEASURING INSTRUMENTS

Subsector : F05 Registration Date : 2011-09-28Organization : UNICountry : ItalyProject ID : 79000360/0001 Project EstablishedICS : 07.060National Ref : U79000360Title : Hydrometry - Measurement of rainfall intensity (liquid precipitation) - Metrological

requirements and test methods for catching type gaugesScope : This standard defines the metrological requirements for rainfall intensity (liquid

precipitation) gauges and establishes classification criteria based on the evaluation of measurement accuracy. This standard is applicable irrespective of the measurement principle (i.e. physical principle on which measurement is based) and the technical and technological characteristics of the specific gauge. The description of test procedures and equipment for calibration and metrological confirmation both in the laboratory and on-site, under steady flow conditions are provided

Page 22

Scope : for the catching type gauges only.



Subsector F07: DOCUMENTATION AND INFORMATION

Subsector : F07 Registration Date : 2011-09-27Organization : SIS Draft Issue Date : 2011-09-27Country : Sweden Latest Date for Comments : 2011-11-27Project ID : 00010701/0001 Draft for public enquiryICS :National Ref : 10701Title : Student information - Information Model Secondary Education AdmissionScope : Quality assurance and management of use of secondary education admission data in

Sweden



Subsector F13: ENVIRONMENTAL TESTS

Subsector : F13 Registration Date : 2011-09-12Organization : SFS Draft Issue Date : 2011-08-31Country : Finland Latest Date for Comments : 2011-11-01Project ID : 0000E275/0001 Draft for public enquiryICS :National Ref :Title : Standard atmospheres for conditioning and testing


Subsector : F13 Registration Date : 2011-09-12Organization : SFS Draft Issue Date : 2011-08-31Country : Finland Latest Date for Comments : 2011-11-01Project ID : 0000E276/0001 Draft for public enquiryICS :National Ref :Title : Preferred test temperatures



Subsector F14: GRAPHICAL TECHNOLOGY, SIGN-BOARDS AND NAMEPLATES

Subsector : F14 Registration Date : 2011-09-13

Page 23

Organization : AENORCountry : SpainProject ID : P0038093/0001 Project EstablishedICS :National Ref : PNE 54131-1Title : Requirements for technical characteristics formalization of the printed graphic product,

by type, during the design process. Part 1: General requirementsScope : This standard specifies the method for the formalization of the technical parameters that

define the printed graphic product, from the design process.


Subsector : F14 Registration Date : 2011-09-13Organization : AENORCountry : SpainProject ID : P0038125/0001 Project EstablishedICS :National Ref : PNE 54131-2Title : Requirements for technical characteristics formalization of the printed graphic product,

by type, during the design process. Part 2: Methods used in advertising and communications printed products

Scope : This standard specifies the method for the formalization of the technical parameters that define the printed graphic product, from the design process.



by type, during the design process. Part 3: Methods used in printed publishing productsScope : This standard specifies the method for the formalization of the technical parameters that




by type, during the design process. Part 4: Methods used in printed industrial productsScope : This standard specifies the method for the formalization of the technical parameters that


Relatedness :

Page 24

National : New


Subsector F19: OPTICS

Subsector : F19 Registration Date : 2011-09-16Organization : DINCountry : GermanyProject ID : 02702312/0001 Project EstablishedICS : 33.180.10National Ref : DIN 58141-3Title : Measurement of fiber optic elements - Part 2: Determination of acceptance angle of light

guides; Text in German and English



Subsector F23: ENERGY

Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891201/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for construction of nuclear facility components. Part 0: General Requirements for

Divisions 1, 2, and 3

Relatedness :National : REV/AMD MSZ 27003-0

Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891202/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for construction of nuclear facility components. Part 1-1: Class 1 Components

Relatedness :National : REV/AMD MSZ 27003-1-1


Relatedness :

Page 25

National : REV/AMD MSZ 27003-1-2



Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891205/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for construction of nuclear facility components. Part 1-5: Component Supports


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891206/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for construction of nuclear facility components. Part 1-6: Core Support Structures


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891207/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for construction of nuclear facility components. Part 1-8: Appendices

Mandatory to series MSZ 27003


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : Hungary

Page 26

Project ID : 34891208/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for construction of nuclear facility components. Part 1-9: Appendices

Nonmandatory to series MSZ 27003


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891209/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for Inservice Inspection of Nuclear Power Plant Components. Part 1: General

Requirements


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891210/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for Inservice Inspection of Nuclear Power Plant Components. Part 2:

Requirements for Class 1 Components







Page 27



Requirements for Class MC and Metallic Liners of Class CC Components



Requirements for Class 1, 2, 3, and MC Component Supports



Requirements for Class CC Concrete Components


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891216/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for Inservice Inspection of Nuclear Power Plant Components. Part 8: Appendices

Mandatory to series MSZ 27011


Page 28

Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891217/0001 Project EstablishedICS : 27.120National Ref :Title : Rules for Inservice Inspection of Nuclear Power Plant Components. Part 9: Appendices

Nonmandatory to series MSZ 27011


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891218/0001 Project EstablishedICS : 27.120National Ref :Title : Code for Operation and Maintenance of Nuclear Power Plants. Part 1: General

Requirements


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891219/0001 Project EstablishedICS : 27.120National Ref :Title : Code for Operation and Maintenance of Nuclear Power Plants. Part 2: Inservice Testing

of Pumps in Light-Water Reactor Nuclear Power Plants



of Valves in Light-Water Reactor Nuclear Power Plants


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891221/0001 Project Established

Page 29

ICS : 27.120National Ref :Title : Code for Operation and Maintenance of Nuclear Power Plants. Part 4: Preservice and

Inservice Examination and Testing of Dynamic Restraints (Snubbers) in Light-Water Reactor Nuclear Power Plants



of Pressure Relief Devices in Light-Water Reactor Nuclear Power Plants


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891223/0001 Project EstablishedICS : 27.120National Ref :Title : Code for Operation and Maintenance of Nuclear Power Plants. Part 6: Check Valve

Condition Monitoring Program


Subsector : F23 Registration Date : 2011-09-28Organization : MSZT Draft Issue Date : 2012-12-27Country : HungaryProject ID : 34891224/0001 Project EstablishedICS : 27.120National Ref :Title : Code for Operation and Maintenance of Nuclear Power Plants. Part 7: Nonmandatory

Appendix



Subsector F99: UNDETERMINED

Subsector : F99 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038288/0001 Project EstablishedICS :

Page 30

National Ref : PNE 166008Title : R&D&i management. Technology transfer.Scope : This standard giver a methodology for the correct realization of technology transfer coming

from, or needed to, R&D&i activities.



** End of Sector **




Sector H : PRODUCTS FOR HOUSEHOLD AND LEISURE USE


Page 32Subsector H06: HOROLOGY

Subsector : H06 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175790/0001 Project EstablishedICS :National Ref : NF S81-551-2Title : Horology - Movements for quartz watches - Part 2: Method for inspection of the

reliability



Subsector H07: SPACE HEATING

Subsector : H07 Registration Date : 2011-09-15Organization : BDSCountry : BulgariaProject ID : BG008001/0001 Project EstablishedICS : 97.100.30National Ref : BDS EN 13240:2006/prNATitle : Roomheaters fired by solid fuel - Requirements and test methodsScope : This national annex supplements BDS EN 13240:2006 and contains national provisions to

this standard taking into account established national traditions and experience in the manufacture and application of the domestic roomheaters fired by solid fuel. It shall be applied in Bulgaria jointly with BDS EN 13240:2006. This national annex contains only those clauses of BDS EN 13808:2006 which make national additions on roomheaters classes as required for carbon monoxide (CO) emissions released in exhaust gasses, efficiency of the appliance, etc.

Relatedness :National : REV/AMD BDS EN 13240:2006


Subsector H23: LADDERS

Subsector : H23 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024134/0001 Project EstablishedICS : 97.145National Ref : ÖNORM Z 1515Title : Trailer ladders - Terms and definitions, types, functional sizes, requirements, testingScope : This Austrian Standard shall be applied to mobile ladders equipped with wheels, rollers, etc.

in order to change position, operated exclusively by human power. This ÖNORM is not applicable to ladders conducted on rails (ladders on casters, shelf ladders, aerial ladders), to automotive ladders or ladders mounted on locomotive vehicles as well as to fire ladders. The ladders are designed for a static vertical maximum load in operating position of 150 kg and shall not exceed a maximum platform size of 400 mm x 400 mm.


Page 33


Subsector H31: DEDICATED LPG APPLIANCES

Subsector : H31 Registration Date : 2011-09-27Organization : DINCountry : GermanyProject ID : 03200521/0001 Published StandardICS : 43.100, 97.200.30National Ref : DIN EN 1949Title : Specification for the installation of LPG systems for habitation purposes in leisure

accommodation vehicles and accommodation purposes in other vehicles; German version EN 1949:2011

Relatedness :National : NewEuropean : Identical to EN 1949:2011-02

Subsector : H31 (Secondary Subsector)


Organization : DINCountry : GermanyProject ID : 03200521/0001 Published StandardICS : 43.100, 97.200.30National Ref : DIN EN 1949Title : Specification for the installation of LPG systems for habitation purposes in leisure

accommodation vehicles and accommodation purposes in other vehicles; German version EN 1949:2011

Relatedness :National : NewEuropean : Identical to EN 1949:2011-02


Subsector H99: UNDETERMINED

Subsector : H99 Registration Date : 2011-09-28Organization : UNICountry : ItalyProject ID : 01089410/0001 Project EstablishedICS : 23.040.70National Ref : E01089410Title : Gas appliances for domestic use - Non-metallic flexible hoses for gas appliances and

similarScope : This Standard definies the design requirements and test methods for non-metallic flexible

hoses for gas appliances and similar with a nominal heat input up to 35 kW, using natural gas and LPG with a pressure up to 25 bar and a range of temperatures between -20°C to 90°C, to be installed in domestic premises and in external parts of buildings.

Relatedness :National : REV/AMD UNI 7140:1993+A1:1995


** End of Sector **




Sector I : MECHANICAL ENGINEERING


Page 35Subsector I02: FASTENERS

Subsector : I02 (Secondary Subsector)


Organization : BSICountry : United KingdomProject ID : 01102187/0001 Project EstablishedICS :National Ref : BS 6SP 4:2000+A3Title : Pins headed, plain shank, drilled, steel alloy and corrosion resisting steel with a strength

class 880/1080 MPa. Amendment


Subsector : I02 (Secondary Subsector)


Organization : BSICountry : United KingdomProject ID : 01102330/0001 Project EstablishedICS :National Ref : BS 4A 116Title : Steel pan head bolts (unified threads) for aircraft. Specification



Subsector I04: ROLLING BEARINGS

Subsector : I04 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024105/0001 Project EstablishedICS : 01.040.21, 21.100.10National Ref : ÖNORM ISO 4378-1Title : Plain bearings - Terms, definitions, classification and symbols - Part 1: Design, bearing

materials and their propertiesScope : This part of ISO 4378 gives the most commonly used terms relating to design, bearing

materials and their properties of plain bearings with their definitions and classification. For some terms and word-combinations, their short forms are given, which can be used where they are unambiguous. Self-explanatory terms are given without definitions.



Subsector I19: NUCLEAR ENERGY

Subsector : I19 Registration Date : 2011-09-28Organization : UNICountry : ItalyProject ID : 54010000/0001 Project Established

Page 36

ICS : 01.040.13National Ref : U54010000Title : Nuclear energy - Glossary of radioprotectionScope : This document establishes and defines the terms used in radioprotection to facilitate the

communication and foster the common understanding


Subsector : I19 Registration Date : 2011-09-28Organization : UNICountry : ItalyProject ID : 54032200/0001 Project EstablishedICS : 13.030.30National Ref : U54032200Title : Solid Materials from nuclear facilities - Radiological methods and procedures for the

clearanceScope : The standard defines the methods and procedures for measuring low levels of radioactivity

in solid materials from nuclear installations, for their removal from regulatory control



Subsector I22: VACUUM TECHNOLOGY

Subsector : I22 Registration Date : 2011-09-16Organization : DINCountry : GermanyProject ID : 06002996/0001 Project EstablishedICS : 01.040.23National Ref : DIN 28400-3Title : Vacuum technology - terms and definitions - Part 3: Vacuum gauges



Subsector I40: INDUSTRIAL PIPING NETWORKS

Subsector : I40 Registration Date : 2011-09-08Organization : LVS Draft Issue Date : 2011-09-15Country : Latvia Latest Date for Comments : 2011-10-17Project ID : 00100026/0001 Draft for public enquiryICS : 75.200National Ref : prLVS 364Title : Operation, maintenance and repair of natural gas storage in aquafier and transmission

pipelines systemScope : The standard defines main requirements for all legal entities and individual persons who

owns or governs natural gas storage and transmission system, as well as for persons who carry out the operational management of these systems and equipment adjustment, technical inspection, exploitation, repair and training for gas specialist.

Page 37

Relatedness :National : REV/AMD LVS 364


** End of Sector **




Sector M : METALLIC MATERIALS


Page 39Subsector M05: WELDING

Subsector : M05 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024106/0001 Project EstablishedICS : 25.160.50National Ref : ÖNORM M 7826-1Title : Soldering and brazing of copper pipes used for installation purposes - Part 1: Filler

metals and fluxesScope : This ÖNORM is applicable for the selction of filler metals and fluxes for the soldering of

copper pipes by soldering or brazing. The performance and testing of soldered and brazed joints are defined in ÖNORM M 7826-2.


Subsector : M05 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024107/0001 Project EstablishedICS : 25.160.50National Ref : ÖNORM M 7826-2Title : Soldering and brazing of copper pipes used for installation purposes - Part 2:

Performance and testing of soldered and brazed jointsScope : This ÖNORM is applicable for the performance and testing of soldered and brazed joints on

copper pipes. Filler metals and fluxes are defined in ÖNORM M 7826-1.



** End of Sector **




Sector N : NON-METALLIC MATERIALS


Page 41Subsector N03: PETROLEUM PRODUCTS

Subsector : N03 Registration Date : 2011-09-01Organization : BSI Draft Issue Date : 2011-08-12Country : United Kingdom Latest Date for Comments : 2011-09-30Project ID : 01102144/0001 Draft for public enquiryICS :National Ref : BS 2869:2010+A1Title : Fuel oils for agricultural, domestic and industrial engines and boilers. Specification.

Amendment



Subsector N06: RUBBER

Subsector : N06 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175511/0001 Project EstablishedICS :National Ref : PR XP T47-764Title : T1 End of life tyres (ELT) T2 Physico-medical and ecotoxicological characterization of

eluates T3 Method(s) of measurement and test protocol(s


Subsector : N06 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175512/0001 Project EstablishedICS :National Ref : PR XP T47-763-2Title : T1 End of life tyres (ELT) T2 Determination of density, porosity and void ratio of tyres

constrained in the abounded state with the aim of their use in Public works and Civil engineering applications T3 ??



Subsector N09: PLASTICS

Subsector : N09 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038265/0001 Project EstablishedICS :National Ref : PNE 53275Title : Plastics. Specifications and test methods for PE shrink films and their copolymers.Scope : This standard specifies characteristics and test methods of thermo-shrink PE films and their

copolymers use in packaging

Page 42



Subsector N14: PLASTICS PIPES

Subsector : N14 Registration Date : 2011-09-02Organization : ASICountry : AustriaProject ID : 00024055/0002 Project EstablishedICS : 23.040.20, 91.140.40National Ref : ÖNORM EN 1555-1/ATitle : Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1:

General (Amendment)Scope : The national amendment of EN 1555-1 ist related to the national Foreword and National

Annex. Because of the publication of EN 1555-4, which is a reference document for the National Foreword and National Annex of EN 1555-1, this revision is necessary.



** End of Sector **




Sector S : HEALTH, ENVIRONMENT AND MEDICAL EQUIPMENT


Page 44Subsector S08: AIR QUALITY

Subsector : S08 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024111/0001 Project EstablishedICS : 21.260National Ref : ÖNORM Z 1263Title : Classification of mist separators for cooling lubricantsScope : This Austrian Standard applies to planar filter media of mist separators for cooling

lubricants. The filter media are classified according to their filtration performance. This Standard is only applicable to water-miscible cooling lubricants (emulsions or solutions) in the concentrations intended for their application, not exceeding 15 vol % of cooling lubricant concentrate in water. This Standard excludes the applicability to non-water-miscible cooling lubricants (cutting oils or bore oils) or to water-miscible cooling lubricants of concentrate over 15 vol % because of possible fire and explosion hazard. This ÖNORM specifies requirements for filter media of mist separators for cooling lubricants. It describes test methods, test bench, the production of test aerosol as well as the methodology for the measurement of filtration performance. The result of the performace measurement according to this ÖNORM cannot be used as direct evidence for the output behaviour during subsequent operation. To achieve results for comparison and classification purposes, the filter media are tested with an atmospheric aerosol. This ÖNORM applies to filter media tested by a volumetric flow within a specified range. Total mist separators for cooling lubricants using these filter media are not dealt with by this ÖNORM. Electrostatic separators, mass force separators, washers and adsorption filters (such as activated charcoal filters) are not covered by this ÖNORM.



Subsector S09: WATER QUALITY AND WATER SUPPLY

Subsector : S09 Registration Date : 2011-09-28Organization : UNICountry : ItalyProject ID : 87045760/0001 Project EstablishedICS : 91.140.60National Ref : U87045760Title : Hot and cold water supply and distribution installations - Design, testing and

management criteriaScope : This standard specifies technical aspects and parameters to be considered for sizing

drinking water systems piping, for calculation of hot water production, storage and distribution, specification for systems operation and non drinking water applications including its limitation. This standard applies to new installations and to repairs or modifications of existing installations. This standard is to be used in conjunction with EN 806 series

Relatedness :National : REV/AMD UNI 9182:2010


Subsector S12: GAS ANALYSIS

Page 45

Subsector : S12 Registration Date : 2011-09-08Organization : NENCountry : NetherlandsProject ID : 50001678/0001 Project EstablishedICS : 13.100, 13.300, 71.100.20National Ref : NTA 7496-2:2011 Concept nlTitle : Toxic gases in shipping containers - Part 2: Medium level training requirements for the

investigation of shipping containersScope : This NTA describes the training requirements for a medium level gas measurement expert

for the release of shipping containers. Training requirements for high level and low level gas measurement experts are described in NTA 7496-1 and NTA 7496-3 respectively.


Subsector : S12 Registration Date : 2011-09-08Organization : NENCountry : NetherlandsProject ID : 50001681/0001 Project EstablishedICS : 13.100, 13.300, 71.100.20National Ref : NTA 7496-3:2011 Concept nlTitle : Toxic gases in shipping containers - Part 3: Low level training requirements for the

investigation of shipping containersScope : This NTA describes the training requirements for a lower level gas measurement expert for

the release of shipping containers.



Subsector S26: ENVIRONMENTAL MANAGEMENT

Subsector : S26 Registration Date : 2011-09-27Organization : SIS Draft Issue Date : 2011-09-26Country : Sweden Latest Date for Comments : 2011-11-26Project ID : 00895400/0001 Draft for public enquiryICS :National Ref : 895400Title : Environmental managementsystems - Guidelines for Green IT use


Subsector : S26 Registration Date : 2011-09-01Organization : BSICountry : United KingdomProject ID : 01102109/0001 Project EstablishedICS :National Ref : BS 8900Title : Guidance for managing sustainable development


Page 46


Subsector S99: UNDETERMINED

Subsector : S99 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024094/0001 Project EstablishedICS : 03.080.30, 03.120.10, 11.020National Ref : ONR 116200-1Title : Quality management in nursing - Part 1: Invasive measures (assistance in punctures)Scope : This ONR determines the process of invasive measures such as preparation and assistance in

punctures.


Subsector : S99 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024095/0001 Project EstablishedICS : 03.080.30, 03.120.10, 11.020National Ref : ONR 116200-2Title : Quality management in nursing - Part 2: Enterale tube feedingScope : This ONR determines the process of achievements in the context of enterale tube feeding,

care of the enterale tube and change of dressing.


Subsector : S99 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024096/0001 Project EstablishedICS : 03.080.30, 03.120.10, 11.020National Ref : ONR 116200-3Title : Quality management in nursing - Part 3: Management of decubitus - Decubitus

prophylaxis and treatmentScope : This ONR determines measures for decubitus prophylaxis and nursing care by present

decubitus.


Subsector : S99 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024097/0001 Project EstablishedICS : 03.080.30, 03.120.10, 11.020National Ref : ONR 116200-4Title : Quality management in nursing - Part 4: Mobilisation

Page 47

Scope : This ONR determines the process to support the patient to move, position change and mobilisation.


Subsector : S99 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024098/0001 Project EstablishedICS : 03.080.30, 03.120.10, 11.020National Ref : ONR 116200-5Title : Quality management in nursing - Part 5: Nursing wound managementScope : This ONR determines the process with diverting systems (Drain) and a general standard

how to change the dressing.


Subsector : S99 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024099/0001 Project EstablishedICS : 03.080.30, 03.120.10, 11.020National Ref : ONR 116200-6Title : Quality management in nursing - Part 6: Diverting systems (drains with suction effect)Scope : This ONR determines the process with diverting systems (Drain) with suction effect.


Subsector : S99 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024100/0001 Project EstablishedICS : 03.080.30, 03.120.10, 11.020National Ref : ONR 116200-7Title : Quality management in nursing - Part 7:Administration of medicationScope : This ONR determines the administration of medication.


Subsector : S99 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024101/0001 Project EstablishedICS : 11.180.30, 91.200National Ref : ÖNORM V 2104Title : Technical aids for blind, visually and mobility impaired persons - Safety devices for

construction and dangerous sites

Page 48

Scope : This ÖNORM is for "work up or next to the street" in accordance to § 90 StVO 1960 for the business of construction site exclusions, construction site safety scaffoldings, roof avalanche exclusions (snow slat) and for transparent obstacle, glass doors, glass areas and that sort of things


Subsector : S99 Registration Date : 2011-09-12Organization : ASICountry : AustriaProject ID : 00024102/0001 Project EstablishedICS : 11.180.30National Ref : ÖNORM V 2103Title : Technical aids for visually impaired and blind persons - Portable transmitters for the

activation of auxiliary equipment for disabled personsScope : This ÖNORM is to be used for portable transmitters for activation of auxiliary equipment at

traffic signal installation and in further consequence also to call of other functions and informations (for example regular service announcements for bus, train and announcements in elevator, acoustic way descriptions in buildings).


Subsector : S99 Registration Date : 2011-09-08Organization : NENCountry : NetherlandsProject ID : 50001679/0001 Project EstablishedICS : 13.200National Ref : NEN 8112:2011 Concept nlTitle : Guidance on evacuation schemes for buildingsScope : This standard is ment as.an instrument for organizations to be prepared on incidents and

calamities. A policy is developed on the basis of risk analysis. This standard contains criteria for setting up a guidance on evacuation schemes.


Subsector : S99 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175577/0001 Project EstablishedICS :National Ref : PR NF X30-024Title : Verification of non-financial data



** End of Sector **




Sector T : TRANSPORT, MECHANICAL HANDLING AND PACKAGING


Page 50Subsector T02: AEROSPACE

Subsector : T02 Registration Date : 2011-09-01Organization : BSICountry : United KingdomProject ID : 01102187/0001 Project EstablishedICS :National Ref : BS 6SP 4:2000+A3Title : Pins headed, plain shank, drilled, steel alloy and corrosion resisting steel with a strength

class 880/1080 MPa. Amendment


Subsector : T02 Registration Date : 2011-09-01Organization : BSICountry : United KingdomProject ID : 01102330/0001 Project EstablishedICS :National Ref : BS 4A 116Title : Steel pan head bolts (unified threads) for aircraft. Specification



Subsector T03: ROAD VEHICLES

Subsector : T03 Registration Date : 2011-09-26Organization : AFNORCountry : FranceProject ID : FA175504/0001 Project EstablishedICS :National Ref : PR NF S61-554Title : Firefighting and rescue service vehicles - Ladder on a carrier and towable ladder

Relatedness :

National :REV/AMD NF S61-554:198311 (S61-554), NF S61-555:197205 (S61-555), NF S61-555/A1:197307 (S61-555/A1)


Subsector T14: PACKAGING

Subsector : T14 Registration Date : 2011-09-30Organization : AENORCountry : SpainProject ID : P0038268/0001 Project EstablishedICS :National Ref : PNE 53206Title : Plastics. Large plastic bags made with plastic films. Characteristics and test methodsScope : This standard specifies the characteristics and test methods for large plastic bags

Relatedness :

Page 51

National : REV/AMD UNE 53206:1983


Subsector T19: ROAD SAFETY

Subsector : T19 Registration Date : 2011-09-30Organization : ASRO Draft Issue Date : 2011-09-30Country : Romania Latest Date for Comments : 2011-12-05Project ID : 18481211/0001 Project EstablishedICS : 93.080.01National Ref : SR 1848-1:2011Title : Road signalisation. Road traffic signs and signalisation tools. Part 1: Classifications,

symbols and locationsScope : This standard establishes the forms, symbols, writtings, colours and placing conditions of

the road traffic signs, conform to actual regulations.

Relatedness :National : REV/AMD SR 1848-1:2008

Subsector : T19 Registration Date : 2011-09-30Organization : ASRO Draft Issue Date : 2011-09-30Country : Romania Latest Date for Comments : 2011-12-05Project ID : 18482211/0001 Project EstablishedICS : 93.080.01National Ref : SR 1848-2:2011Title : Road signalisation. Road traffic signs and signalisation tools. Part 2: Technical

requirementsScope : This standard establishes the technical requirements for road traffic signs and other

signalisation means (dimensions, execution details, packaging and storing, installation, quality conditions and quality control).


Subsector : T19 Registration Date : 2011-09-30Organization : ASRO Draft Issue Date : 2011-09-30Country : Romania Latest Date for Comments : 2011-12-05Project ID : 18483211/0001 Project EstablishedICS : 93.080.01National Ref : SR 1848-3:2011Title : Road signalisation. Road traffic signs and signalisation tools. Part 3: Design and

descriptionScope : This standard establishes the technical conditions for the design and inscriptioning for road

traffic signs mentionned in SR 1848-1:2011, includind inscriptions, graphics, installation schemes.



** End of Sector **




Sector Z : INFORMATION TECHNOLOGY


Page 53Subsector Z99: UNDETERMINED

Subsector : Z99 Registration Date : 2011-09-27Organization : SIS Draft Issue Date : 2011-09-27Country : Sweden Latest Date for Comments : 2011-11-27Project ID : 00011900/0001 Draft for public enquiryICS :National Ref : 11900Title : Cloud computing - TerminologyScope : Terms and definitions - Cloud computing

Relatedness :National : NewInternational : Not Equivalent to Ongoing work in JTC1 SC 38 SGCC


** End of Sector **

2011-06

List of non-electrotechnical subsectors

Sector A: Services

Subsector Title ISO/TC CEN/TC

reference reference

A01 Tourist services / 329; CEN/WS ETO

A02 Cleaning services / 328

A03 Postal services / 331

A04 Transportation services / 320; CEN/WS 016; CEN/WS SCUTUM

A05 Maintenance services / 319

A06 Building and construction services / 330

A07 Translation services /

A08 Funeral services / CEN/BT/TF 139

A09 Facility management / 348

A10 Services of Real Estate Agents / CEN/BT/TF 180; 373

A11 Security Services / CEN/BT/TF 167; 391; 384; 370; CEN/WS 044; CEN/CLC/TC 4

A12 Consultancy Services / 395; 381

A13 Expertise Services / 405

A14 Aesthetic Services / 403;409

A99 Undetermined / CEN/WS 002; CEN/WS 004; CEN/WS 037; CEN/WS 039; CEN/WS 041; CEN/WS 051; 375; 374; 376; 385; 404

Sector B: Building and construction


reference reference

B01 Fire protection 21 70; 72; 191; 192

B02 Structures 59; 98 166; 167; 250; 277; 346; 349; 284; 288; 297; 340

B03 Concrete 71 104; CEN/WS 009

B04 Cement 74; 77 51

B05 Fire tests 92 127

B06 Gypsum / 241

B07 Glass 160 129

B08 Doors and windows 162 33

B09 Thermal matters 163 88; 89; 371; CEN/BT WG 173; CEN/WS 036

B10 Timber structures 165 124

B11 Metal structures 167 135

B12 Masonry 179; 196 125; 246

B13 Solar energy 180 312

B14 Geotechnics 182 341; 396

B15 Sanitary appliances / 163; 7

B16 Taps / /

B17 Lighting equipment and lighting / 50; 169 application technology

B18 Scaffolding / 53

B19 Ceramic tiles 189 67

B20 Drainage equipment / 165

B21 Baths / /

B22 Wallcoverings / 99

B23 District heating / 107

B24 Auxiliary and handicraft work / /

B25 Gas distribution installation and / 234; 235; 282 related equipment

B26 Road building and maintenance / 178; 227

B27 Waterproofing materials / 128; 254; 361; 314

B28 Floor coverings 38/SC 12 134

B29 Aggregates / 154

B30 Floor and surfacing / 217; 303; 323; 390

B31 Heating systems in buildings / 228; 247

B32 Precast concrete products / 177; 229

B33 Building design 205 315; 325; 388

B34 Building and construction – Environmental aspect 350; 351

B99 Undetermined / /

Sector C: Chemicals, chemical engineering and food products


reference reference

C01 Food products 34 174; 275; 302; 360; 307; 327; 338; 387; CEN/WS 008; CEN/WS 018; CEN/WS 054

C02 Paints and related products 35 139; 298; 173

C03 Chemistry 47 317; 363

C04 Laboratory glassware 48 332

C05 Lac / /

C06 Essential oils 54 /

C08 Pesticides 81 /

C09 Surfactants 91 276

C10 Starch 93 /

C11 Tobacco 126 401

C12 Glass plant / /

C13 Fertilizers 134 223; 260

C16 Wood preservatives / /

C17 Trees and plants / /

C18 Adhesives / 193

C19 Chemical analysis 201; 202 382; 347

C20 Explosives and firework / 212; 321

C21 Cosmetics 217 392

C22 Bio-Based products / 411

C99 Undetermined / 386

Sector F: Fundamental standards


reference reference

F01 Technical drawings 10 /

F02 Units & symbols 12 /

F03 Preferred numbers 19 /

F04 Sieves 24 /

F05 Measuring instruments 30; 113 92; 171; 176; 237;

294; 318; 244; 367; 141; CEN/WS 011

F06 Terminology principles 37 /

F07 Documentation and information 46 304; CEN/WS 024 CEN/WS 010 CEN/WS 023 CEN/WS 028 CEN/WS 014 CEN/WS 050 CEN/WS 006 368

F08 Surfaces / 290

F09 Banking 68 /

F10 Statistics 69 /

F12 Information processing systems 204 224; 225; 251; 278; CEN/WS CPF CEN/WS CIS CEN/WS ODR CEN/WS CID 287; 311; 365

F13 Environmental tests / /

F14 Graphical technology, 130 / sign-boards and nameplates

F15 Material testing in general 135 138; CEN/WS 007 CEN/WS 021 CEN/WS 033

F16 Graphical symbols 145 /

F17 Administrative documents 154 CEN/WS MMU

F18 Micrographics 171 /

F19 Optics 172; 187 123; 170

F20 Quality assurance 176 CEN/CLC/TC1 CEN/CLC/WG QS CEN/WS 030 362

F21 Value analysis and project / 279 network

F22 Logistics / 379; 273

F23 Energy 203 CEN/CLC/JWG 1; CEN/CLC/JWG 2;

CEN/CLC/JWG 3; CEN/CLC/JWG 4; CEN/WS 027

F99 Undetermined / 389; CEN/WS 057; CEN/WS 058; CEN/WS 060

Sector H: Products for household and leisure use


reference reference

H01 Cinematography 36 372

H02 Photography 42 /

H03 Consumer questions / 291

H04 Sports equipment 83 136

H05 Oil and gas burners / 47; 131

H06 Horology 114 /

H07 Space heating 116 62; 110; 130; 179; 180

H08 Sizing systems 133; 137 /

H09 Furniture 136 207

H10 Sewing machines 148 /

H11 Heater controls 161 58

H12 Ceramic and glass-ware for food 166 /

H13 Jewellery 174 CEN/WS 047

H14 Caravans 177 245

H15 Toys 181 52

H17 Oil stoves / 46

H18 Central heating boilers / 48; 57; 109; 269

H19 Non-electric cookers and barbecues / 49; 281; 295

H22 Smokers’ lighters and matches / 355; 87

H23 Ladders / 93

H24 Tactile danger warnings / /

H25 Large gas appliances / 106; CEN/CLC/JWG FCGA

H26 Sealing materials / 108; 208

H27 Educational equipment / /

H28 Hunting 191 /

H29 Heat pumps / 113

H30 Equipment for children / 252

H31 Dedicated LPG appliances / 181

H32 Culinary utensils 186 194

H33 Footwear (excluding protective / 309 footwear)

H34 Child safety / CEN/BT/WG 117 398

H99 Undetermined / 299; 364; 369; 402

Sector I: Mechanical engineering


reference reference

I01 Screw threads 1 /

I02 Fasteners 2 185

I03 Limits & fits / /

I04 Rolling bearings 4 /

I05 Iron pipes 5 203

I06 Pressure vessels 11 54

I07 Shafts 14 /

I08 Agricultural machines 23 144, 334

I09 Small tools 29 213

I10 Splines / /

I11 Machine tools 39 142; 143; 145; 255

I12 Pulleys & belts 41 188

I13 Gas containers 58 23; 286

I14 Gears 60 /

I15 Equipment for petroleum industry 67 12

I16 Internal combustion engines 70; 192 270

I17 Machinery in general 72; 199 114; 153; 214; 313 (including safety) 271, 337; 399; 397 CEN/WS 025

I18 Mining 82 196

I19 Nuclear energy 85 /

I20 Refrigeration 86 44; 182

I21 Chains and chain wheels 100 /

I22 Vacuum technology 112 /

I23 Pumps 115 197

I24 Industrial fans 117 356

I25 Compressors 118 232

I26 Plain bearings 123 /

I27 Earth moving and construction 127; 195 151 equipment

I28 Fluid power 131 /

I29 Gas cleaning / 195

I30 Air distribution / 156

I31 Valves 153; 185 69; 236; 105

I32 Flanges / 74

I33 Information processing in 184 310 automation

I34 Non-ferrous metallic pipes / /

I35 Leisure and recreational machines / 152

I36 Thermoprocessing technology / 186

I37 Printing and paper machines / 198

I38 Leather production, tannery and / 200; 201 related machinery

I39 Machines for metal processing / 202; 322

I40 Industrial piping networks / 267

I41 Membrane filters / 272

I42 Potentially explosive atmospheres / 305

I43 Hydrogen energy 197 /

I44 Nanotechnologies 229 352

I99 Undetermined / CEN/CLC/JTF PE; CEN/CLC/TC 2; 65, 157; CEN/WS 059

Sector M: Metallic materials


reference reference

M01 Steel 17 CEN/TC 342; 344; ECISS/TC 6 ECISS/TC 7 ECISS/TC 9 ECISS/TC 10 ECISS/TC 11 ECISS/TC 12 ECISS/TC 13 ECISS/TC 15 ECISS/TC 19 ECISS/TC 20 ECISS/TC 21 ECISS/TC 22 ECISS/TC 23 ECISS/TC 24 ECISS/TC 26 ECISS/TC 27 ECISS/TC 28 ECISS/TC 29 ECISS/TC 5 ECISS/TC 14 ECISS/TC 100 ECISS/TC 102 ECISS/TC 103 ECISS/TC 104 ECISS/TC 105 ECISS/TC 106 ECISS/TC 107 ECISS/TC 108 ECISS/TC 109 ECISS/TC 110

M02 Zinc / 209

M03 Foundry technology, 25 190; ECISS/TC 31 ECISS/TC 111 including cast iron

M04 Copper 26 133

M05 Welding 44 121

M06 Dimensions of wrought products / /

M07 Manganese and chromium 65 /

M08 Light alloys 79 132

M09 Iron ores 102 /

M10 Metallic coatings 107 240

M11 Powder metallurgy 119 /

M12 Aluminium ores 129 /

M13 Ferroalloys 132 /

M14 Nickel 155 /

M15 Metallic corrosion 156 262; 219

M16 Mechanical tests for metals 164 ECISS/TC 1 ECISS/TC 2 ECISS/TC 101

M17 Heavy metal ores 183 /

M18 Metal wire products / ECISS/TC 30; CEN/BT/TF 196; 378; 407

M20 Tin and tin alloys / 220

M21 Precious metals / 283

M22 Lead and lead alloys / 306

M99 Undetermined / /

Sector N: Non-metallic materials


reference reference

N01 Paper and board 6 172

N02 Solid fuels 27 335; 343;383; CEN/WS 019

N03 Petroleum products 28 19; 336; CEN/WS 038; CEN/WS 061

N04 Refractories 33 187

N05 Textiles 38 189; 248

N06 Rubber 45 218; 366 CEN/WS 003

N07 Sawn timber 55 38; 175

N08 Mica / /

N09 Plastics 61 249

N10 Cork 87 /

N11 Wood-based panels 89 112

N12 Timber products 99 /

N13 Leather 120 289

N14 Plastics pipes 138 155

N17 Fluorspar 175 /

N18 Glass-fibre reinforced plastics / /

N19 Tapes / 253

N20 Ceramics 206 184

N21 Gaseous fuels and combustible gas 158; 193 238; 408

N22 Feather and related materials / 222

N23 Diamond / 410

N99 Undetermined / /

Sector S: Health, environment and medical equipment


reference reference

S01 Acoustics and sound 43 126; 211 insulation

S02 Transfusion equipment 76 /

S03 Syringes 84 /

S04 Protective clothing and equipment 94 85; 158; 159; 160; 161; 162; CEN/WS 026; CEN/WS 043

S05 Dentistry 106 55

S06 Vibration & shock 108 231

S07 Anaesthetic and respiratory 121 215 equipment

S08 Air quality 146 137; 243; 264; CEN/CLC/JWG CMI

S09 Water quality and water supply 147 164; 230; CEN/WS 001 CEN/WS 034

S10 Surgical implants 150 285; CEN/CLC/JWG AIMD

S11 Contraceptives 157 /

S12 Gas analysis / /

S13 Ergonomics 159 122

S14 Prosthetics 168 /

S15 Surgical instruments 170 /

S16 Aids for the disabled 173 293

S17 Respiratory protective devices / 79

S18 Sterilization of equipment 198 102; 204

S19 First aid equipment and rescue systems / 239

S20 Waste collection, handling and / 183 transportation

S21 Laboratory medicine, clinical 194 140; 206; 233; pathology and biosafety 257; 258; 316; CEN/CLC/TC 3; CEN/WS 031; CEN/WS 053; CEN/WS 055

S22 Energy saving / CEN/WS 005 CEN/WS 015

S23 Personal & property protection against aggression/Burglary protection / 263

S24 Soil quality 190 345; CEN/WS 032

S25 Chemical disinfectants and / 216 antiseptics

S26 Environmental management 207 CEN/TC 406; CEN/WS 040

S27 Waste - Characterization, treatment / 292; 308; and streams CEN/BT/TF 120

S28 Demining / CEN/WS 029 CEN/WS 013

S99 Undetermined / 205; CEN/BT/TF 127 394; 259; 357; 358; 359; 380; 400; CEN/WS PCEC CEN/WS 012 CEN/WS 020

Sector T: Transport, mechanical handling and packaging


reference reference

T01 Shipbuilding and maritime 8; 188 15; 300 structures

T02 Aerospace 20 274; AECMA; ECSS ;377

T03 Road vehicles 22 301; 326 CEN/WS IMA

T04 Tyres 31 /

T05 Pallets 51 /

T06 Metal and plastic containers 52 210; 221; 265; 266; 268; 296 393

T07 Glass containers 63 /

T08 Cranes 96 147

T09 Materials handling and 101 148; 149 storage equipment

T10 Freight containers 104 119; 280

T11 Steel wire ropes 105 /

T12 Industrial trucks 110 150; 324

T13 Lifting chains, hooks and ropes 111 168

T14 Packaging 122 261; 120

T15 Cycles 149 333

T16 Lifts & escalators 178 10; 242

T17 Builders hoists / /

T18 Elevating platforms / 98

T19 Road safety / 226; 339

T20 Tram- and railway engineering / 256; / CEN/CLC/WG FPR

T21 Packaging machines / 146

T22 Off-road vehicles / 354

T99 Undetermined / CEN/WS TAF

Sector Z: Information technology


Z01 Radiocommunication for IT / /

Z02 Telephony, telegraphy for IT / CEN/CLC - ETSI

Z03 Common O.S.I. activities / CEN/CLC - EWOS

Z99 Undetermined / 353; CEN/WS ADN; CEN/WS AUT; CEN/WS BII; CEN/WS CAT; CEN/WS CST; CEN/WS CTC; CEN/WS DFA; CEN/WS DIR; CEN/WS DIS; CEN/WS DPA; CEN/WS DPP; CEN/WS EBE; CEN/WS ECH; CEN/WS ECO; CEN/WS EFI; CEN/WS EMD; CEN/WS ESI; CEN/WS ESR; CEN/WS EUR; CEN/WS FAS; CEN/WS FIN; CEN/WS FS2; CEN/WS FUN; CEN/WS GEN; CEN/WS HIC; CEN/WS ICT; CEN/WS IEC; CEN/WS IHM; CEN/WS INV2; CEN/WS ISD; CEN/WS JXF; CEN/WS KMA; CEN/WS LCT; CEN/WS LTS; CEN/WS MDC; CEN/WS MEE; CEN/WS MES; CEN/WS MET; CEN/WS MLX; CEN/WS MMI; CEN/WS NEA; CEN/WS NOM; CEN/WS ORC; CEN/WS POR; CEN/WS QIS; CEN/WS SAN; CEN/WS SCE; CEN/WS TEX; CEN/WS TWE; CEN/WS UDP; CEN/WS URI; CEN/WS WAC;

CEN/WS XFS; CEN/WS XML; CEN/WS eGo; CEN/WS eIN; CEN/WS ePR

Documents

Monthly Notifications Register - SUTN · 2011-11-07 · Information procedure Page 1 Monthly Notifications Register Notifications registered at CCMC from 2011-09-01 to 2011-09-30